Welcome to the SeeMeCNC Community

The leads were not tinned I checked when I took it apart. I cut the burnt part of the connector off and soldered the wire to the back of the board.
Good news it works not pretty but its not getting hot anymore. The bed temp seems to climb higher and faster now.

We're can I buy one of those?

Hi guys,

Looking to add the probe to my rostock v2 currently using 713 mount and e3d v6. How hard is it to wire up?

any tips would be great.

my board melted looking to buy a used one.

Noticed my extruder motor was making funny noises. Then I smelled burning took the Rambo out and it was melting. [img]http://i11.photobucket.com/albums/a182/deadpool2099/IMG_0192_zpstgwc7zjb.jpg[/img] Can I just resolder the heated bed wire to the back of the board? Hopefully the capacitor wasn't ...

Adjusted my alpha rotation 1 degree from 330 to 229 and it worked extrusion remains tight to the bed between towers.

After nailing the z height I was able to get the gaps to fill in using a circle calibration print prints out perfectly. Then I tried a large print surface and I'm getting lift between y and z and x and z. I've been reading about alpha rotation but it gives me a headache lol. Any further suggestions ...

Well on the bag it did say 300.15 rod length which is what I plugged into the eeprom setting. I'm going to hit it hard when I get home.

I ran the alternate calibration routine to set horizontal radius took about 40 runs before it was close 145.33 Radius if anyone else is using the 300 mm carbon fiber arms. When I added the trucks I ran the routine again and it was still good all points dragging on a 009 feeler gauge. It seems like I ...

What would be the best way to tighten up the belts the gaps have gotten wider since I upgraded to trick trucks.

Well I feel like Im getting closer and farther away at the same time. Installed the trick trucks and ran a calibration print can somone tell me what the hell is going on with the low spot. Sorry pic was taken from my netcam [img]http://i11.photobucket.com/albums/a182/deadpool2099/NetCam1-12.15.04 ...

So after going through putting the old arms back on figuring that had to be the issue I think one of my carriages is messed up. Doing the alternate calibration routine I realized one of the towers will be good and then when I run the routine it will be high again. Checked it out and the leveling ...

Using the alternate calibration method I can get every point correct except between the towers upper right. Not sure what the hell is wrong

If I hadn't just bought the 713 mount and e3d Inwould just get the 280 with probe.

Hi everyone, The struggle is real with my preowned romax v2. I have slowly been upgrading, fixing, and calibrating. I have everything dialed in but keep having an issue with a high point between the x and y tower as well as filament not going to the edges in and around the same spots. I noticed the ...

well to my surprise 3 more rounds and every point was dragging on the feeler gauge.

Hi guys, I have been struggling to calibrate my printer and based off of another thread I thought I would try another method. I bought a set of feeler gauges and went to town and did about 25 rounds based on the flow chart. I'm using appendix b http://download.seemecnc.com/rostockmax ... dition.pdf ...

Watching my print and I noticed a slight click on the z axis. Noticed the bearing covers look torn up in spots.

Maybe part of the issue?

The extrusion multiplier is set to 95% by default what should it be set to 100%?

Maybe Ill give cura or kiss a shot and see if that fixes it. I would very much like the printer to be as accurate as possible its been a pain but Im not going to give up.

Ill give the filament measurement a shot to.

i did switch the nozzle to .40 as soon as I replaced it

I tried adjusting the widths to no avail tried 40 .48 .50

Gaps around buttons tried adjusting overlap no dice seems to make no difference. Just upgraded to e3d v6 and 300mm carbon fiber arms [img]http://i11.photobucket.com/albums/a182/deadpool2099/20170207_145139_zpsmg5h9kpi.jpg[/img] Im using simplify 3d current settings top layer 4 bottom layers 4 outer ...

Its a v2 with the most recent firmware.

Hi guys, Sorry for all the posts but Im dead set on getting my printer dialed in after upgrading arms,e3d,ect. My issue is I have a point between y and z were the filament wont stick to the bed. Every time I adjust and reset z height it seems like it throws all the points off. They will be to low ...

care to share the coupon code?

well I assume I would just adjust it out to 300mm but what about horizontal radius?

just ordered the trick laser arms. Have a quick question fo I need to adjust firmware values?

upgrading from the factory ballcup arms.