Welcome to the SeeMeCNC Community

... ordered and installed the wrong part. (and it continued to fail with the bed leveling) I received the needed SMD part a few days after the new board (which corrected the stress gauge sensing issues resulting in successful bed leveling). And with the correct part I was able to repair and verify the old ...

... it died of - the probe results being "inconsistent". When I try to do the bed leveling it moves down, towards the back then immediately after first probe (moving down) it seems to slip(?) further out then it does the same type of stutter on most of the rest of the probe points. One or two seeming ...

... is I can see that there was something mounted there before.. And since bed leveling/probing was hit or miss the part had weak solder joints and got knocked off the board at some point and is lost to me.. I am a new 3d hobbyist that got lucky and found an Artemis for $100 cant really afford to buy a ...

You'll get that if the heat bed is on during probing or if the nozzle is dirty.

g.

... d/1IQf191FP7EgV8IRpa__jZviF_lfd1jcKVwHD2J7U9pw/edit my problem now is the G29 Error: Z probe readings are not consistent when I do calibration... do I need to change something in the config file? post that I asked about it in duet3d forum https://forum.duet3d.com/topic/34345/bed-level/5 thank you!

What parameters do you need?

g.

hello, I want to calibrate and level the bed on printer ROSTOCK MAX V3.2 the seemecnc manual that I used for the update said not to use G29 run mash and I cannot see the bed map. Page 12 said to do some configuration on the config file, but I don't know the parameters... also, I have a z probe problem ...

... M666 X0 Y0 Z0 ; endstop adjustment (this is set by autocalibration leveling) ; Network ;M540 P0xF0:0xE1:0xD2:0xC3:0x11:0x11 ; Set your own MAC ... value, offset and trigger height M557 R130 S30 ; define mesh grid ; Bed Heater M308 S0 P"bedtemp" Y"thermistor" T100000 B4725 C7.06e-8 ...

The plugin may need to be updated for the latest Octoprint. I don't have the time to do it, sorry.

g.

... on the latest version of octoprint? Gene's work has been fantastic and the only reason i still have my RMv2.5. Bed leveling is a problem for me. thanks!

... layers), etc - to the point I realized that I now have to run the leveling script pretty much before every single print. It seems to always have a ... have happened to the printer to make this the case now? No matter what other issues I've had with my SeeMe deltas, the bed level was never one of them.

... probe_radius 127 # where to probe zprobe.probe_height 74 # how much above bed to start probe switch.servo.enable true switch.servo.input_on_command ... servo.pwm_period_ms 20 # Set Period to 20ms (50Hz) - Default is 50Hz leveling-strategy.three-point-leveling.tolerance 0.05 # the probe tolerance in ...

... version. Maybe I should measure the distance between the effector and the bed to see if it's parallel. Another idea is to make the leveling screws exactly the same height before trying to auto-level. Here are the details of auto-leveling on the Smoothieboard: http://smoothieware.org/zprobe GcodeV31.png ...

... It has Smoothieboard 32-bit electronics. I've been trying to get auto-leveling to work. Adjusting the screws on each tower doesn't work well enough anymore. I added a bltouch v3.1 to the Smoothieboard and have the process working. However, it does not level the bed. G28; #home to max endstops M280 S3 ...

Thanks for all the tips. So the smart effector allows for auto bed leveling? It looks good, and I would buy the whole hotend setup, but my problem is that I want to be able to print high temp filaments like nylon and nylon mixed with carbon fiber and that hotend assembly doesn't look like it can do that ...

... were super tightened down warping- tried using painters tape, turning up bed temps, keeping room printer is in warm and staying away from temp ... 1000 Thermistor Phaetus Dragon 70W 500C Heaters blTouch Automatic bed leveling sensor Maybe new carriages? Not sure on if there is a better ...

... on my printer and after starting it back up, I attempted to map the bed for a test print. But, while leveling, the settings appeared to be way off. I still ran a test print and while the center appeared correct, but the print head rose progressively higher the more it travels from the center. I ...

... M666 X0 Y0 Z0 ; endstop adjustment (this is set by autocalibration leveling) ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ... value, offset and trigger height M557 R130 S30 ; define mesh grid ; Bed Heater M308 S0 P"bedtemp" Y"thermistor" T100000 B4725 C7.06e-8 ...

... M666 X0 Y0 Z0 ; endstop adjustment (this is set by autocalibration leveling) ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ... value, offset and trigger height M557 R130 S30 ; define mesh grid ; Bed Heater M308 S0 P"bedtemp" Y"thermistor" T100000 B4725 C7.06e-8 ...

... I can strap a smart effector on there and get the functionality of mesh bed leveling? but 713 Maker's adapter is not good? Just to be clear, the smart effector you are referring to is the smart effector kit from duet? https://e3d-online.com/products/smart-effector-kit-for-delta-printer thank you, -Rev

Those self-inflicted wounds hurt the most.

Glad you got it sorted!

g.

Pully grub screws!!! Apparently I forgot to lock tight the threads.

... I noticed my belts where a little loose. So I tightened them a little and I made the mistake of running the first probe instead of just probe and now I can't get the bed level. I try the same benchy and just the foot print of the benchy has almost 1mm of deviation. I have no idea how to proceed.

... up my Rostock Max v1 from the original Indiegogo campaign in 2012. The bed isn't flat. I adjusted the leveling screws to get it as level as possible. There are still some odd high and low spots on the bed. Could it be that the wood under the heated bed has warped? Is there a metal alternative? Is ...

... Smart Effector setup will save you some cash if all you need is an easy bed leveling sensor. This is the setup I'm using with E3D hotends and I'm very happy. Another alternative is to go ahead and sell the old Rostock and buy/build a 300x300x400 (or larger) coreXY... :D Edit 4/2021 : If you have the ...