Welcome to the SeeMeCNC Community

ok so how do I know which place in the pins menu to change the TEMP_0 to pin 8??? I see multiple arduino mega lists that all look the same... I changed the tempsensor to the 100 value, and havnt yet wired it bc what good is that when it isn't goin to read correctly to know if I wired it correctly ...

this is support isn't it ... also my lcd is all solid blocks?

new Rambo, uploaded repetier file into arduino, and then into eeprom... why does the bed auto turn on upon powering up the printer? what file do I need to look at to change this. the last time I was using this printer, I would manually turn the bed on from my manual control...

ordering it tomorrow, will be back with some more questions sooner or later! im still foggy where I change the thermistor reading to the thermocouple reading, it talked about the 100 value, but I couldn't find that list in my repetier arduino file when I looked last night... seems I understand how ...

so this is what im trying to get? http://www.mouser.com/ProductDetail/Analog-Devices/AD597AH/?qs=sGAEpiMZZMuH431S2KcKU0CNH6mMvT4A3q5GHzstGHg%3d or I found this talkin a little about the thermocouple extensions... http://reprap.org/wiki/Rambo_development#Thermocouple_and_additional_thermistors even ...

this might also redirect others, http://forum.seemecnc.com/viewtopic.php ... 7&start=10
it helps to read thru others comments first, but I missed it till earlier...

that's the adafruit board I looked at? knew I shoulda got that one... and i seen ur thread nosing around, i'll just stay tuned to that one, thanks

alright so I got a new Rambo, its getting power and I have this I2C with the +/- from the thermocouple into the blue connector, and I have 3.3 going into pin1 along with its - to pin2 (on the 10pin connector) just rubber banded for now... these two white leads are from T0 on the Rambo, I need to ...

this is the board and the link shows firmware and stuff pins assingments but still might enjoy some assistance!
i know i have to give 3.3 to pin1 and ground pin2. pin 5 and 6 are data lines, SCL and SDA that form the I2C line, from what i know from a short reply from oilmex support.

hey guys, looking for some assistance. I had shorted something on my board a while back having to do with the hotend, but was wanting to upgrade it to get more heat out of her anyways. I got the inDimension3 hotend and have seen over 700F degrees with just hooking the same power to the dual ...

i need to switch from E1 back to E0, but don't know what tab in the aurdino to find it in... also i think i blew my fuse for the extruder, its in the heat0 position, is the heat1 run off the same fuse, or can i swtich to heat1 and im good again? if so i don't know where to change that in my repetier ...

Thermistor is reading right, one of my fuses is not reading. I like your idea to soldier one over the top of it, thanks for that! how do I change E1 back to E0?

I desperately need to remember how to change my feed motor from E1 where it is position now, to E0. it'd been running good while printing red, and then I switched to black, and it started bogging again... I'd tried tuning my temp and flow settings a bit bc it kept boggin and backing up, and you can ...

sry, forgot, the pic shows the unfinished part in the foreground, and im holding the previous part to show the height that this part should have ended up. and what was printed of the part looks good, and is to spec, so im curious what causes a freeze error, and also it doesn't describe anything in ...

what could cause the printer to freeze in the middle of a 2.3 hr print, second time its done it to me. otherwise my rostock has been working according to my printer settings, which im honing! I haven't messed with anything besides my print settings since it started printing. it is running at 45mm at ...

I use alibre as much as I hate to plug them, but I think It had to do with m "feature pattern" which was the support material I built in the groove, I take those supports fins and its ok, so ive found another way to modle my support without using the cirular feature pattern! thanks foor the info!

this is the file im trying to print...

im having a problem getting retetier to slice a part, but its telling me in my log, that the object is non-manifold. im curious what section of my part it is referencing? ive changed the part a few times now, it was previously talkin about there was a hole too close to an edge or something along ...

definitely a bad E0 on the board, john was kind enough to help me switch the settings of E0 to E1 and it now feeds! you don't know how Fu King happy I am! I just cant wait to get printing and order s'more stuff. you guys may not like me now, but I will assure you, this is how most of my first ...

there has to be a g-code I can manually input to control the motor besides pressing the button right? I just want to further eliminate that aspect before I have to call them again, wouldn't want to waste anybody's time, if its NOT the board I mean... I really just wanted to print some stuff like a ...

ya that's what these arrows were for huh? id hit them a couple times without anything happening prior to me running this check that you instructed me to do, and I neve knew what they did bc nothing happened... so when I check, nothing happened, I opened the zip and extracted to a new folder and ...

I am currently trying to extrude abs and it will hold at 240, and yes repetier host is what I am using for the time being, till I can print something and make the distinction if I will continue to use repetier host. I can hand feed the hot end, and a blockage isn't the problem as much as the motor ...

where can i find a list of codes that might tell me how to manually control this feed stepper. im sick to death of this thing not working! i paid my money, i assembled this MF, and it's calibrated, what else do i have to do to get it to spit out a print? the only thing i "haven't" done is sweet-talk ...

I have the regular extruder setup, not the EZ, requardless, when I unplugged my X,Y,and Z from Rambo and plugged the feed stepper into the x it worked fine, so motor is not messed up, my board isn't messed up either, and I don't know how to manually move the feed stepper with it plugged into it E0 ...

It gets up to and holds strong at 240, nothing smoking or anything, heatbed was also steady at 60, the feed motor isn't pushing and filament, this looks nothing like a cube, ha... but I am serious that I want this thing to work... my speed in the slic3r printer setting is 60 like it shows. what am I ...