When does the Eris enter production?
-
- ULTIMATE 3D JEDI
- Posts: 1409
- Joined: Sun May 11, 2014 6:18 pm
Re: When does the Eris enter production?
Will it be using the stock, SeeMeCNC nozzles?
R-Max V2
Eris
Folger Tech FT-5 R2
Eris
Folger Tech FT-5 R2
Re: When does the Eris enter production?
Our HE280 is a new design using a single 30mm blower and single heating resistor. The accelerometer is under the blower. The blower blows up. The valve can be turned to control air flow part either on or off. The intake of the blower pulls air across the heat sink to cool the hot end.
~PartDaddy
SeeMeCNC Owner & Founder
Blackpoint Engineering is SeeMeCNC
Since 1996
SeeMeCNC Owner & Founder
Blackpoint Engineering is SeeMeCNC
Since 1996
Re: When does the Eris enter production?
Is it possible to mount the new hot end assembly below the effector plate?
The main reason I have my current hot ends below the plate is to make the nozzle more visible to a time lapse camera. It also generally makes it easier to remove stray filaments wit forceps, without having the effector, ball ends and arms so close to the nozzle.
The gains of having a sensor may very well outweigh these other advantages.
The main reason I have my current hot ends below the plate is to make the nozzle more visible to a time lapse camera. It also generally makes it easier to remove stray filaments wit forceps, without having the effector, ball ends and arms so close to the nozzle.
The gains of having a sensor may very well outweigh these other advantages.
Last edited by AlanZ on Tue May 03, 2016 9:21 am, edited 1 time in total.
Re: When does the Eris enter production?
you'd have to make an adapter, we haven't done that
~PartDaddy
SeeMeCNC Owner & Founder
Blackpoint Engineering is SeeMeCNC
Since 1996
SeeMeCNC Owner & Founder
Blackpoint Engineering is SeeMeCNC
Since 1996
Re: When does the Eris enter production?
I added a few notes to my previous post.
I would be happy to make an adapter, if you don't see any reason that one would not work.
Thanks for your insights.
I would be happy to make an adapter, if you don't see any reason that one would not work.
Thanks for your insights.
-
- ULTIMATE 3D JEDI
- Posts: 1561
- Joined: Wed Sep 23, 2015 2:55 pm
Re: When does the Eris enter production?
Will you guy's be publishing the board size soon? I would like to figure out what sort of mount would be needed to get it working with an E3D (No slight intended towards you guy's hotends, but with the sunk costs of my hotend set, and the desire to keep PT100's, I'm not planning to use the new one with it (I may work with getting the old stock one to play nice with it)). Presuming of course that you make the board available separately from the hotend.
Machines:
Rostock Max V2, Duet .8.5, PT100 enabled E3D V6 and volcano, Raymond style enclosure
Automation Technology 60W laser cutter/engraver
1m X-carve router
Sic Transit Gloria Mundi
01-10011-11111100001
Rostock Max V2, Duet .8.5, PT100 enabled E3D V6 and volcano, Raymond style enclosure
Automation Technology 60W laser cutter/engraver
1m X-carve router
Sic Transit Gloria Mundi
01-10011-11111100001
Re: When does the Eris enter production?
Here you go. This is literally work I just finished today. Have fun, happy hacking.
https://github.com/seemecnc/eris_delta/ ... 0hot%20end
Note the push to connect is not in there. It's pressed in john guest PTC fitting. The circuit board and components are perfect because they are the actual part files used to make everything. Also, all of these Solidworks files are 100% accurate to the current production model. Note the tiny height difference under the No.4 sheet metal screws. This is to pinch the circuit board firmly in place. We are making the very last mold tomorrow. Nathan will be machining the middle section of the blower ducting. The first fully functional Eris will be running Friday (what could possibly go wrong?).
BTW, we will machine another aluminum heat sink for groove mounting our new hot end.
https://github.com/seemecnc/eris_delta/ ... 0hot%20end
Note the push to connect is not in there. It's pressed in john guest PTC fitting. The circuit board and components are perfect because they are the actual part files used to make everything. Also, all of these Solidworks files are 100% accurate to the current production model. Note the tiny height difference under the No.4 sheet metal screws. This is to pinch the circuit board firmly in place. We are making the very last mold tomorrow. Nathan will be machining the middle section of the blower ducting. The first fully functional Eris will be running Friday (what could possibly go wrong?).
BTW, we will machine another aluminum heat sink for groove mounting our new hot end.
~PartDaddy
SeeMeCNC Owner & Founder
Blackpoint Engineering is SeeMeCNC
Since 1996
SeeMeCNC Owner & Founder
Blackpoint Engineering is SeeMeCNC
Since 1996
-
- ULTIMATE 3D JEDI
- Posts: 1409
- Joined: Sun May 11, 2014 6:18 pm
Re: When does the Eris enter production?
And Y'all are going on vacation on Monday?
R-Max V2
Eris
Folger Tech FT-5 R2
Eris
Folger Tech FT-5 R2
Re: When does the Eris enter production?
Hah! Mac. Vacation? Not so much, well not monday Steve's headed out next week to drive the PartDaddy and the Eris machines out to the Bay Area MakerFaire, JJ and I are flying out on the 18th, then i'm driving back with the trailer, and JJ is flying back the following monday. Plenty of work left to do, like, the DropLit v2 drops next week too
-
- ULTIMATE 3D JEDI
- Posts: 1409
- Joined: Sun May 11, 2014 6:18 pm
Re: When does the Eris enter production?
"Out for Delivery" WOOT!!!!
R-Max V2
Eris
Folger Tech FT-5 R2
Eris
Folger Tech FT-5 R2
-
- ULTIMATE 3D JEDI
- Posts: 1409
- Joined: Sun May 11, 2014 6:18 pm
Re: When does the Eris enter production?
Ooooh, a box with a handle... now that's good design!
Mine won't get here until later this week, it's still in transit.
Mine won't get here until later this week, it's still in transit.
-
- ULTIMATE 3D JEDI
- Posts: 1409
- Joined: Sun May 11, 2014 6:18 pm
Re: When does the Eris enter production?
I'll have plenty of visitors in my work area today!
R-Max V2
Eris
Folger Tech FT-5 R2
Eris
Folger Tech FT-5 R2
-
- ULTIMATE 3D JEDI
- Posts: 1409
- Joined: Sun May 11, 2014 6:18 pm
Re: When does the Eris enter production?
So I'm dredging this one up from a year ago. I have # 32. A year has gone by and I'm curious what has changed with the Eris production? What sort of running changes have been made?
R-Max V2
Eris
Folger Tech FT-5 R2
Eris
Folger Tech FT-5 R2