Hi
i have installed E3D and i don't know where to start to increase the temp limit on the hot end. searched for a guide with no luck.
can i change it from EEPROM configuration in repetier host?
how to increase the max hot end temp
- Eaglezsoar
- ULTIMATE 3D JEDI
- Posts: 7185
- Joined: Sun Apr 01, 2012 5:26 pm
Re: how to increase the max hot end temp
There is a max temp setting in the configuration.h of your firmware which you would need to increase then upload the firmware to themrbdrm wrote:Hi
i have installed E3D and i don't know where to start to increase the temp limit on the hot end. searched for a guide with no luck.
can i change it from EEPROM configuration in repetier host?
Rambo board using Arduino.
“ Do Not Regret Growing Older. It is a Privilege Denied to Many. ”
Re: how to increase the max hot end temp
ok
is there something i need to do before that? backup? or simply modify the maxtemp value then upload?
is there something i need to do before that? backup? or simply modify the maxtemp value then upload?
- Eaglezsoar
- ULTIMATE 3D JEDI
- Posts: 7185
- Joined: Sun Apr 01, 2012 5:26 pm
Re: how to increase the max hot end temp
You should just modify the setting in configuration.h then upload. Make sure that the maxtemp value you are changingmrbdrm wrote:ok
is there something i need to do before that? backup? or simply modify the maxtemp value then upload?
is for the extruder.
“ Do Not Regret Growing Older. It is a Privilege Denied to Many. ”
Re: how to increase the max hot end temp
thank youEaglezsoar wrote:You should just modify the setting in configuration.h then upload. Make sure that the maxtemp value you are changingmrbdrm wrote:ok
is there something i need to do before that? backup? or simply modify the maxtemp value then upload?
is for the extruder.
i have done it and everything is good
what layer fan mount you guys recommend with this mount http://www.thingiverse.com/thing:137140" onclick="window.open(this.href);return false; from 626Pilot
the stock one is lower than the nozzle now.
- Eaglezsoar
- ULTIMATE 3D JEDI
- Posts: 7185
- Joined: Sun Apr 01, 2012 5:26 pm
Re: how to increase the max hot end temp
That is one of the problems with going to the E3D and I don't know if anyone ever created a layer fan that works withoutmrbdrm wrote:thank youEaglezsoar wrote:You should just modify the setting in configuration.h then upload. Make sure that the maxtemp value you are changingmrbdrm wrote:ok
is there something i need to do before that? backup? or simply modify the maxtemp value then upload?
is for the extruder.
i have done it and everything is good
what layer fan mount you guys recommend with this mount http://www.thingiverse.com/thing:137140" onclick="window.open(this.href);return false; from 626Pilot
the stock one is lower than the nozzle now.
sticking out so far it could risk banging on the uprights. If anyone knows what works best as a layer fan after installing
an E3D please step in and let us know.
“ Do Not Regret Growing Older. It is a Privilege Denied to Many. ”
Re: how to increase the max hot end temp
how about this http://www.thingiverse.com/thing:304011" onclick="window.open(this.href);return false;
- Eaglezsoar
- ULTIMATE 3D JEDI
- Posts: 7185
- Joined: Sun Apr 01, 2012 5:26 pm
Re: how to increase the max hot end temp
That one looks great! I don't know how I missed that one but I'm glad you did not.mrbdrm wrote:how about this http://www.thingiverse.com/thing:304011" onclick="window.open(this.href);return false;
Thanks for finding it and sharing with us! I am printing one out as soon as I can.
GREAT FIND!
“ Do Not Regret Growing Older. It is a Privilege Denied to Many. ”