Delta Arm Blues?? Or something else??
Delta Arm Blues?? Or something else??
So I've printed 10 of these z-calibration test and there seems to be no improvement. All of them are printed in the center of the glass plate.
Before printing out the next Z-calib i tweeked the filament diameter and extrusion widths to test which would be the best. I thought that at one point Id finally get a perfect print.
I've tried differnt temperatures for the extruder and bed as well.
My question has to do with #9 and #10
I printed out the just the first layer of #9 and it came out perfectly. But when i did the print again without changing anything the infill wasnt correct. And then i tried the same for #10 and had different errors.
Im aware of delta arm blues are but I have the tricklaser arms. I always thought that the D.R.B had to to with the friction of the arms due to improper sanding. Could it be possible that my tricklaser bands are too tight causing too much friction?
Does anyone know why I cant infill correctly? Any advice?
[img]http://i.imgur.com/dkQ7Gq2.jpg[/img]
[img]http://i.imgur.com/Yq4crxw.jpg[/img]
[img]http://i.imgur.com/SlECBXm.jpg[/img]
[img]http://i.imgur.com/K9jj3vO.jpg[/img]
Before printing out the next Z-calib i tweeked the filament diameter and extrusion widths to test which would be the best. I thought that at one point Id finally get a perfect print.
I've tried differnt temperatures for the extruder and bed as well.
My question has to do with #9 and #10
I printed out the just the first layer of #9 and it came out perfectly. But when i did the print again without changing anything the infill wasnt correct. And then i tried the same for #10 and had different errors.
Im aware of delta arm blues are but I have the tricklaser arms. I always thought that the D.R.B had to to with the friction of the arms due to improper sanding. Could it be possible that my tricklaser bands are too tight causing too much friction?
Does anyone know why I cant infill correctly? Any advice?
[img]http://i.imgur.com/dkQ7Gq2.jpg[/img]
[img]http://i.imgur.com/Yq4crxw.jpg[/img]
[img]http://i.imgur.com/SlECBXm.jpg[/img]
[img]http://i.imgur.com/K9jj3vO.jpg[/img]
Re: Delta Arm Blues?? Or something else??
You might be under extruding, have you properly calibrated your extruder?
Re: Delta Arm Blues?? Or something else??
Mike, your avatar is deeply disturbing.
g.
g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Re: Delta Arm Blues?? Or something else??
What, you afraid of rainbow dash? a lil MLP scare you? >:)
Re: Delta Arm Blues?? Or something else??
AAAAAAUUUUUUGGGGHHHH!!!!!
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Re: Delta Arm Blues?? Or something else??
Someone is a lil over dramatic
Re: Delta Arm Blues?? Or something else??
..says the guy with the dangerous psycho-pony as his avatar...
g.
g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Re: Delta Arm Blues?? Or something else??
Are you using KISSlicer or something else?
(It's probably not the bands)
(It's probably not the bands)
Questions? Ask in a thread - PMs are off.
AI Calibration | Dimensional Accuracy Calibration | Hand-Tune your PID | OctoPi + Touchscreen setup | My E3D hot end mount, Z probe, fan ducts, LED ring mount, filament spool holder, etc.
AI Calibration | Dimensional Accuracy Calibration | Hand-Tune your PID | OctoPi + Touchscreen setup | My E3D hot end mount, Z probe, fan ducts, LED ring mount, filament spool holder, etc.
- Eaglezsoar
- ULTIMATE 3D JEDI
- Posts: 7185
- Joined: Sun Apr 01, 2012 5:26 pm
Re: Delta Arm Blues?? Or something else??
As disturbing as bubbasnow's? His gives me an epileptic seizure.geneb wrote:Mike, your avatar is deeply disturbing.
g.
Re: Delta Arm Blues?? Or something else??
Rainbow Dash isn't dangerous.... D:
Re: Delta Arm Blues?? Or something else??
i represent that comment..Eaglezsoar wrote:As disturbing as bubbasnow's? His gives me an epileptic seizure.geneb wrote:Mike, your avatar is deeply disturbing.
g.
- Eaglezsoar
- ULTIMATE 3D JEDI
- Posts: 7185
- Joined: Sun Apr 01, 2012 5:26 pm
Re: Delta Arm Blues?? Or something else??
You're Welcome.bubbasnow wrote:i represent that comment..Eaglezsoar wrote:As disturbing as bubbasnow's? His gives me an epileptic seizure.geneb wrote:Mike, your avatar is deeply disturbing.
g.