Smart LCD Adapter - draft
Smart LCD Adapter - draft
I have some difficulties to adapt the Smart LCD adapter for the Rambo. I decide to begin with the pinout diagram. In this first rush the schematics will be made by hand (with mspaint, I know, but it's rapid).
The ISP is correct, I think (on the right side, 2x4 pins)
For the EXT2 (1x18 pins), the nbr of pin is 20 and on the smart adpater 18. I'll post later after testing all needed infos.
Don't hesitate to say if this type of doc already exists in the forum (fater multiple search I cannot find info).
Attached to this message, the draft. Sorry for my poor english, I'm french speaking.
Regards
The ISP is correct, I think (on the right side, 2x4 pins)
For the EXT2 (1x18 pins), the nbr of pin is 20 and on the smart adpater 18. I'll post later after testing all needed infos.
Don't hesitate to say if this type of doc already exists in the forum (fater multiple search I cannot find info).
Attached to this message, the draft. Sorry for my poor english, I'm french speaking.
Regards
Owned a Rostock Max acrylic version with Onyx heater bed.
Re: Smart LCD Adapter - draft
The simpliest operation is to create a new pcb design larger but with a direct connection to the EXT2 and SPI (and the connectors will be the same as main board : 2x4 connector and 2x10) , we have have the needed space for that!
Owned a Rostock Max acrylic version with Onyx heater bed.
Re: Smart LCD Adapter - draft
I used these kind of connectors:
and it took me about 15 minutes to complete the full adapter-cable. With preparing and double-checking.Re: Smart LCD Adapter - draft
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Re: Smart LCD Adapter - draft
Geneb,
I've already read this thread and the PDF too .
But I want to connect the wires on the adapter provided with the LCD and not directly on LCD.
Or we can also add a column in the connexion table for the adapter ?
I've already read this thread and the PDF too .
But I want to connect the wires on the adapter provided with the LCD and not directly on LCD.
Or we can also add a column in the connexion table for the adapter ?
Owned a Rostock Max acrylic version with Onyx heater bed.
Re: Smart LCD Adapter - draft
If I recall correctly, the RAMPS 1.4 adapter board doesn't even come close to fitting the RAMBo properly. That's why I built and documented it the way I did.
g.
g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Re: Smart LCD Adapter - draft
Nope, doesn't fit RAMBo.
However! We got the adapters in last week in qty
Here they are!
http://www.shop.seemecnc.com/LCD-to-RAM ... 2RAMBO.htm
However! We got the adapters in last week in qty
Here they are!
http://www.shop.seemecnc.com/LCD-to-RAM ... 2RAMBO.htm
Re: Smart LCD Adapter - draft
Needs a photo John!
g.
g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Re: Smart LCD Adapter - draft
Could someone who has this new adapter up a photo, so that the new people such as myself can be sure of which one they have. It's kinda confusing, oh, and thanks in advance!
"Now you see why evil will always triumph! Because good is dumb." - Spaceballs
Re: Smart LCD Adapter - draft
Flateric wrote:Could someone who has this new adapter up a photo, so that the new people such as myself can be sure of which one they have. It's kinda confusing, oh, and thanks in advance!
there is one in my build log
My rostock build log http://forum.seemecnc.com/viewtopic.php?f=42&t=1228
- Jimustanguitar
- ULTIMATE 3D JEDI
- Posts: 2631
- Joined: Sun Mar 31, 2013 1:35 am
- Location: Notre Dame area
- Contact:
Re: Smart LCD Adapter - draft
Same adapter that came with my kit, nice design. Fits like a glove.cambo3d wrote:Flateric wrote:Could someone who has this new adapter up a photo, so that the new people such as myself can be sure of which one they have. It's kinda confusing, oh, and thanks in advance!
there is one in my build log
I understand that this LCD kit replaces having to run Repetier, but all of the initial setup and troubleshooting steps that I've found use this software. Has anybody created a guide for commissioning a Rostock with only the LCD?