Page 1 of 1
Hello from Charlotte!(Fort Mill SC side)
Posted: Wed May 21, 2014 5:02 pm
by RJLynn67
Yall have been more of a help that you know. I have been lurking and reading for a bit now and just pulled the trigger on a Max v2 and a bunch of filament to put on me bench next to the Form1 and dwarf the ever living out of it!
I can't wait to start the build and get to printing!
A Special thanks to John Guanu who I badgered for the past few days with questions though the support chat window on the site!
Let's Do It!
Re: Hello from Charlotte!(Fort Mill SC side)
Posted: Wed May 21, 2014 11:18 pm
by Boundless
Congrats RJ,
Happy to hear your machine is on the way. I'm still a very new printer but learning more every day.
If i can help a fellow NC builder and printer, lemme know.
Re: Hello from Charlotte!(Fort Mill SC side)
Posted: Thu May 22, 2014 12:22 am
by Eaglezsoar
RJLynn67 wrote:Yall have been more of a help that you know. I have been lurking and reading for a bit now and just pulled the trigger on a Max v2 and a bunch of filament to put on me bench next to the Form1 and dwarf the ever living out of it!
I can't wait to start the build and get to printing!
A Special thanks to John Guanu who I badgered for the past few days with questions though the support chat window on the site!
Let's Do It!
Welcome to the Forum!
Let's all hope that you have a great build and many hours of fun printing out whatever your mind can dream up!
We have a diverse group of people on the forum who can help if you need it or perhaps you can participate and help others.
Either way, we welcome you and wish to say Happy Printing!
Re: Hello from Charlotte!(Fort Mill SC side)
Posted: Thu May 22, 2014 2:59 am
by Demolishun
Can't wait to see you get your machine running!
Re: Hello from Charlotte!(Fort Mill SC side)
Posted: Thu May 22, 2014 10:38 am
by RJLynn67
Anyone using windows 8.1 with the software?
Re: Hello from Charlotte!(Fort Mill SC side)
Posted: Thu May 22, 2014 11:19 pm
by geneb
FYI, John and Guanu are two different people.
g.
Re: Hello from Charlotte!(Fort Mill SC side)
Posted: Fri May 23, 2014 12:16 am
by Eaglezsoar
geneb wrote:FYI, John and Guanu are two different people.
g.
Yea, John does all the work and Guanu takes all the credit!!
Re: Hello from Charlotte!(Fort Mill SC side)
Posted: Fri May 23, 2014 7:36 am
by RJLynn67
Ahh interesting. He said to make a note about the great support I was given by "John Guanu" O well.
so about windows 8.1? Are we good there?
Re: Hello from Charlotte!(Fort Mill SC side)
Posted: Fri May 23, 2014 8:18 am
by Eaglezsoar
RJLynn67 wrote:Ahh interesting. He said to make a note about the great support I was given by "John Guanu" O well.
so about windows 8.1? Are we good there?
Not many responses, I do not run windows 8 however there have been several reports from those who do and were able to
run the applicable software. That is the limit of my knowledge but I think you will be fine.
Re: Hello from Charlotte!(Fort Mill SC side)
Posted: Fri May 23, 2014 2:45 pm
by RJLynn67
Sounds good! Getting excited over here waiting for it to show!
Re: Hello from Charlotte!(Fort Mill SC side)
Posted: Fri May 23, 2014 5:06 pm
by RAMTechRob
I run Windows 8 with the software. No problems for me.
Re: Hello from Charlotte!(Fort Mill SC side)
Posted: Tue May 27, 2014 3:00 pm
by RJLynn67
OHHHH YEEEEAAAAAHHHHHH! IT Shipped!
Very excited over here!