no response from Rostock MAX V3

Introduce yourself to the community!
Post Reply
Dexter Carhart
Plasticator
Posts: 8
Joined: Thu Jul 22, 2021 11:53 am

no response from Rostock MAX V3

Post by Dexter Carhart »

Hello. I don't know if I have a hardware issue but I was told everything is in working order. I can't seem to get any response whatsoever from my printer in terms of controlling the hot end/heatbed ect. Nothing on the printer will even move when I use any of the controls on Mattercontrol. I followed all of the Rostock MAX v3 setup instructions properly. Mattercontrol says that my printer is connected. Has anyone else had this issue?
geneb
ULTIMATE 3D JEDI
Posts: 5362
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Re: no response from Rostock MAX V3

Post by geneb »

Can you control the printer through the front panel?

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Dexter Carhart
Plasticator
Posts: 8
Joined: Thu Jul 22, 2021 11:53 am

Re: no response from Rostock MAX V3

Post by Dexter Carhart »

I cannot. The dial is not scrolling through different sections/ options. I am just stuck on the main screen. does this mean I have a hardware issue?
geneb
ULTIMATE 3D JEDI
Posts: 5362
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Re: no response from Rostock MAX V3

Post by geneb »

Can you post a photo of what your screen looks like?

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Dexter Carhart
Plasticator
Posts: 8
Joined: Thu Jul 22, 2021 11:53 am

Re: no response from Rostock MAX V3

Post by Dexter Carhart »

Here it is.
Attachments
C1C69F9C-CDB3-4C93-A8ED-F13EC9654B52.jpeg
C1C69F9C-CDB3-4C93-A8ED-F13EC9654B52.jpeg (240.18 KiB) Viewed 4285 times
geneb
ULTIMATE 3D JEDI
Posts: 5362
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Re: no response from Rostock MAX V3

Post by geneb »

I think I mentioned this before - if there's a wiring issue to the HE280's PCB, the firmware will hang on initialization, which it appears to be doing in your photo.

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
geneb
ULTIMATE 3D JEDI
Posts: 5362
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Re: no response from Rostock MAX V3

Post by geneb »

Check for shorts in the wiring harness - if there aren't any, you should probably reach out to [email protected].

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Post Reply

Return to “New Member introduction”