hi, the base of the spining top prints right, then it gets to the tower part, and after a short bit the print screws up, as shown in the picture.
this is standard pla, 0.2 layer, 20 % infill (i also tried 15% same thing happens) i also tried different temps, 210, 215, 220, etc.. same hting happens..
any ideas?
thanks all.
print problem, printing a spinning top with tower top, tower comes out wrong
print problem, printing a spinning top with tower top, tower comes out wrong
------------------------
Magic Marc
ARTEMIS & H2
Magic Marc
ARTEMIS & H2
-
- ULTIMATE 3D JEDI
- Posts: 1409
- Joined: Sun May 11, 2014 6:18 pm
Re: print problem, printing a spinning top with tower top, tower comes out wrong
The printer needs to slow down when in is printing that detail. Or you need more cooling
R-Max V2
Eris
Folger Tech FT-5 R2
Eris
Folger Tech FT-5 R2
Re: print problem, printing a spinning top with tower top, tower comes out wrong
Yep. Too hot, too fast, or both.
g.
g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Re: print problem, printing a spinning top with tower top, tower comes out wrong
thanks everyone, im going to slow it down now, and cool it down, with temp and fans.
thx
marc
thx
marc
------------------------
Magic Marc
ARTEMIS & H2
Magic Marc
ARTEMIS & H2
Re: print problem, printing a spinning top with tower top, tower comes out wrong
You might want to look into the minimum layer time of whatever slicer you use. That will guarantee it'll slow down as it prints the center of the top.
g.
g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Re: print problem, printing a spinning top with tower top, tower comes out wrong
im using mattercontrol to slice and print to h2 hacker.
im having error using cura to slice and mattrercontrol to upload gcode and print, the gcode generated from cura looks and is wrong when added to the que in mattercontrol.
im having error using cura to slice and mattrercontrol to upload gcode and print, the gcode generated from cura looks and is wrong when added to the que in mattercontrol.
------------------------
Magic Marc
ARTEMIS & H2
Magic Marc
ARTEMIS & H2
Re: print problem, printing a spinning top with tower top, tower comes out wrong
I can just about guarantee there's nothing wrong with Cura if you've got it configured properly. I can't say the same for MatterControl.
My advice is to slice on Cura and either print via SD card or use a Raspberry Pi & Octoprint.
g.
My advice is to slice on Cura and either print via SD card or use a Raspberry Pi & Octoprint.
g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Re: print problem, printing a spinning top with tower top, tower comes out wrong
THAKNS AS ALWAYS GENE AND EVERYONE. I WILL TRY THE SD CARD PRINT TODAY/TONIGHT.
AS WELL IS THERE A GOOD YOUTUBE LINK OR INSTRUCTIONS TO USE OCTOPRINT?
THANKS
AS WELL IS THERE A GOOD YOUTUBE LINK OR INSTRUCTIONS TO USE OCTOPRINT?
THANKS
------------------------
Magic Marc
ARTEMIS & H2
Magic Marc
ARTEMIS & H2