Welcome to the SeeMeCNC Community

Not my model, i pulled it from here

Im attempting to barter with some local WH40k guys and have them paint it for me

30 hours later... [img]https://lh3.googleusercontent.com/U_UvS6noP7I70Dy8c3WagVOLSYl5M1Hkkuf3IDkZhNjb=w1716-h965-no[/img] [img]https://lh3.googleusercontent.com/y_zVWZ7T3aavdCF5r8IlzCzqdOJI1vdC1bAWI-i7I0r2=w1716-h965-no[/img] [img]https://lh3.googleusercontent.com/FalUs-iMPT3DALzknxdOlKAtXfZyD5lpBxM...

It was my setup which was causing a hickup. i use my pi to power 4ch relay, i have the heatbed power supply, lights, and printer main supply on it. the pi would be powered up before the smoothie. I cut the 5vdc line on my usb host cable so that only 5v supply was from the 12v printer supply. when th...

Ive got everything up and going now, calibrations went good. Im looking to get my second extruder hooked up and i noticed that the config for delta machines is using "extruder_module_enable" but all other configs are using "extruder.hotend1.enable ". Am I ok with updating these p...

took a nap, now its working

im using my Pi to try and connect without success, it looks like its refusing the usb conneciton

i did these e-chain links with volcano 1.2mm nozzle 1mm height. PLA. 230deg 45mm/sec what would have cost me a couple hundred, i did with 4lbs of pla :) did it all in a weekend [img]https://lh3.googleusercontent.com/Do25d_V8buflk3nJgReblUCjtCHF3ROryyRATnxPwGY=w437-h246-no[/img] [img]https://lh3.goog...

you should hollow out a pocket on the nose, big enough for the magnet, then seal it in with the bottom/top layers

kjmagnetics.com

alright got my smoothie up and running... lets do this!!

[img]https://lh3.googleusercontent.com/hJh49 ... 16-h965-no[/img]

alright that was it, im rolling the white one.. adjusted with needle nose and now i can see

i cant get the contrast to adjust, do you think its because im missing those pins next to the sd slot?

answered my own question.. 3.25 and 3.26 arent pinned out.

mine came pre soldered, ive tried it on 2 glcd boards with no luck so it really looks like a connection issue.

here is the pins [img]https://lh3.googleusercontent.com/iFzKg ... 43-h965-no[/img]

well i physically installed the two ribbons ext1/2, and i copied and pasted the code snippet from the GLCD wiki into the section ( although it was mostly already there just "#" commented out). can you copy your entire config here so i can do a line by line compare? Thanks

i get displays going but the encoders arent moving the pointer up and down the menus. is yours working?

BBB is the brains and CRAMPS is the motor controller, there are different boards out that do the same thing as CRAMPS or more... i think they are up to 10stepper motor on a bebopr++ with optional muxer. Gotta keep your head in the machinekit google groups to stay in the know. I have a working bbb+be...

I have finally been able to set up octoprint on my Raspberry Pi, get the pi connected to the internet (required learning how to build a kernel module for my unsupported wifi dongle), and actually connect to my printer. I guess I just don't know what to do next. I'm a total newb at printing. I have ...

ive actually had really good luck with single layers using the volcano 1.2mm end. water tight vases for days!!

We used to use THPP at work, adding it to resign to change its density.

75 dollars for 1lb of raw powder.

http://www.tungstenheavypowder.com/shop ... n-powders/

what about amf format?

depends on material, if you are using abs you can use acetone to clean nozzles out, else you can heat up with lighter/torch and pick the plastic out.

you should move the point where it mounts to the base of the cold section instead of the hot section, you only need 2 screws in the fans anyways.

does it have the same bed? same tower distance? same effector? same carriages?

I wonder how this would work with volcano