Search found 99 matches

by wildideas1
Tue Nov 19, 2013 9:56 am
Forum: General Tips 'N Tricks
Topic: How to calibrate without PC attached
Replies: 11
Views: 7988

Re: How to calibrate without PC attached

where are you putting the script?? is this for the SD card use?? still haven't tried mine yet.
by wildideas1
Tue Nov 19, 2013 9:52 am
Forum: What are YOU making?
Topic: November Print Challenge
Replies: 32
Views: 22686

Re: November Print Challenge

well 3rd time wasn't a charm it 2 fell over at 4min left in the print, not sure what issue is i think it is the jerkiness of slcr it swings all the way around in full circle to go to each post and i see very slight jerk ?? how do i stop that issue if that wasnt their then maybe will finish. on ...
by wildideas1
Mon Nov 18, 2013 9:09 pm
Forum: What are YOU making?
Topic: November Print Challenge
Replies: 32
Views: 22686

Re: November Print Challenge

well not as easy as it looks i have a pile of 8 tube 4 of which are 1 1/2" tall and other 4 were only 3/4" from finishing the print when i'm guessing cold draft effected back corner of the machine, it sits in corner of my office at far wall where draft from stairs swirl air current. the piece just ...
by wildideas1
Mon Nov 18, 2013 4:11 pm
Forum: What are YOU making?
Topic: November Print Challenge
Replies: 32
Views: 22686

Re: November Print Challenge

well at 96mm one leg decided it had enough and popped off plate not sure why but it did and of course it did it live on ustream so i was able to go in and stop clean bed and restart the process
by wildideas1
Mon Nov 18, 2013 2:10 pm
Forum: What are YOU making?
Topic: November Print Challenge
Replies: 32
Views: 22686

Re: November Print Challenge

printing live http://ustre.am/MpTj
by wildideas1
Mon Nov 18, 2013 2:07 pm
Forum: Live Stream Announcments
Topic: November challenge
Replies: 0
Views: 3180

November challenge

I am broadcasting live at http://ustre.am/MpTj come and check it out!
by wildideas1
Wed Oct 09, 2013 10:21 pm
Forum: Troubleshooting
Topic: mach 3 setup
Replies: 9
Views: 6931

Re: mach 3 setup

What is your .? My son and I run both H1 mach3 and rostock setup
by wildideas1
Wed Oct 09, 2013 10:07 pm
Forum: What are YOU making?
Topic: rock stocks 4th print ever
Replies: 5
Views: 4880

Re: rock stocks 4th print ever

Thingaverse 3 different styles labled lady bust
by wildideas1
Wed Oct 09, 2013 10:02 pm
Forum: Rostock MAX
Topic: Time for a full teardown...
Replies: 16
Views: 10669

Re: Time for a full teardown...

Hey cope check out the post on my son and I's rostock we just finished build week ago , is labled gone and done it again you will see how we ran the wiring up from base to top for the 3 spool set up used 1'' wire molding track and dremald a notch into the baSe and top by 1/4" for good tight fit ...
by wildideas1
Tue Oct 01, 2013 8:57 pm
Forum: What are YOU making?
Topic: rock stocks 4th print ever
Replies: 5
Views: 4880

Re: rock stocks 4th print ever

Rostock is correct midnight lack of sleep and spellcheck does not help
by wildideas1
Tue Oct 01, 2013 1:47 am
Forum: What are YOU making?
Topic: rock stocks 4th print ever
Replies: 5
Views: 4880

rock stocks 4th print ever

well my son and i decided on adding the Rockstock to our table when he was 9 we built the H-1 and now for his 11th b-day i said lets build the rock stock, 1,2nd print failed due to extruder coils going kaput snagged from H-1 and up and running again 3rd was beauty and sliced with on board slicer ...
by wildideas1
Tue Oct 01, 2013 1:35 am
Forum: Show us your machine!
Topic: gone and done it again
Replies: 1
Views: 2481

gone and done it again

Well its been a year and a half since my 9yr old son and I built a H-1 and have been using it for lots of fun and work related things. ME (dad) decided to take the leap and get a Rockstock now while we had problems during the build all issues were taken care of by SEEMECNC immediately and with ...
by wildideas1
Sun Aug 18, 2013 1:58 pm
Forum: The Lounge
Topic: H1-1 For sale
Replies: 2
Views: 3089

Re: H1-1 For sale

I interested for another 1 for my son
by wildideas1
Sat May 18, 2013 10:47 pm
Forum: New Member introduction
Topic: New to the 3D printer club
Replies: 9
Views: 8030

Re: New to the 3D printer club

Welcome I too just ordered a delta I have a H1 that my son 9yr old built a yr ago and we have a blast, we have never printed a yoda so we would be the 1st 3d printer to not print Yoda dont have the stl file to try it.
Maybe the delta will be the 1st to print it for us
by wildideas1
Sat May 11, 2013 11:04 am
Forum: General Tips 'N Tricks
Topic: Fuses for LED Lights and Fans
Replies: 2
Views: 3116

Re: Fuses for LED Lights and Fans

those leds look like a 20ma set up you really don't need a fuse in line they should be a 12v led module and being a Diode they act like a fuse when they blow if they do blow they become open and power will not flow anymore. if you do put a fuse inline a 1amp will suffice. you will only be drawing ...
by wildideas1
Sat May 04, 2013 10:57 pm
Forum: General Tips 'N Tricks
Topic: Precise Extruder Steps Per MM
Replies: 2
Views: 3376

Re: Precise Extruder Steps Per MM

Ok I see that no one has ever asked this but are you extruding with hot end or extruder cold with tip off unit like calibrating the h1
by wildideas1
Sat Nov 03, 2012 11:02 am
Forum: The Build Zone
Topic: Adman234 H1.1 Build Progress and Questions
Replies: 27
Views: 21778

Re: N00b needs advice from the pros for first build!

hello: i am fairly new in this about 4 months but my son and i have been rocking along we have had issues you can search them and answers we have gotten from everyone in group and they have always been spot on. we have had awesome luck with ABS we have never tried PLA. we have bought rolls on the ...
by wildideas1
Thu Oct 18, 2012 11:32 am
Forum: Live Stream Announcments
Topic: Live stream attempt
Replies: 0
Views: 4207

Live stream attempt

ok we are going to try this for 1st time live
I will be attempting a multi color twist glass
starting at 9:45am Mtn time
http://www.ustream.tv/channel/wildideas1
by wildideas1
Tue Oct 09, 2012 1:30 pm
Forum: KISSlicer
Topic: KISSlicer and Cura with LinuxCNC
Replies: 12
Views: 14813

Re: KISSlicer and Cura with LinuxCNC

i wondered that in begging but if you hold mouse over area it gives exp for each area
Ian
by wildideas1
Mon Oct 08, 2012 11:44 am
Forum: General Tips 'N Tricks
Topic: Material usage extruded??
Replies: 3
Views: 3459

Re: Material usage extruded??

aw ha found it Son and I have been using Kisslicer and it works awesome each box that you can change values on has a flyover explination of what it does (very helpful for newbies and such) and yes I never payed attention to the box about cost of operation and such till you pointed it out in your ...
by wildideas1
Sun Oct 07, 2012 10:18 am
Forum: Troubleshooting
Topic: hourglass shaping
Replies: 0
Views: 2126

hourglass shaping

DSCF1863.JPG
Ok printed a Bio-hazard medallion 2 night ago printed darn clean some tweaking needed on fill but the side wall while layers were absolutely awesome instead of being a straight 90 degree side it has hourglass shape.

any ideas???

Ian
by wildideas1
Sun Oct 07, 2012 9:42 am
Forum: General Tips 'N Tricks
Topic: Material usage extruded??
Replies: 3
Views: 3459

Material usage extruded??

ok I admit i am horrible at math and need help. i have been having a blast last week printing after i got some issues resolved but i have never seen anyone ask this or just say it. at the end of the g-code it lists time to build material usage and cost example build Thursday 128.26 minutes 13.383 cm ...
by wildideas1
Mon Oct 01, 2012 7:26 pm
Forum: Troubleshooting
Topic: extruder oozing
Replies: 1
Views: 3464

extruder oozing

ok how does one stop the material from coming out the resistors area all of a sudden im oozing out a wad of abs size of gum after 2 hours of printing took completed apart cleaned made sure all was tight and still oozes if i need to make extruder slower how do i change in motor tuning and what value ...
by wildideas1
Mon Jul 23, 2012 2:19 pm
Forum: What are YOU making?
Topic: rockets
Replies: 3
Views: 4170

rockets

Ok new heat bed and up early on sat so I printed 4 rockets for my son and we then had fun shooting them off, 1st one went about 250' and came back down about 75' from us took about 15 to find spent motor casing but we like to keep our park clean. video of 1st launch 2nd one went around 500 but we ...
by wildideas1
Mon Jul 23, 2012 1:59 pm
Forum: Show us your machine!
Topic: My son and I H1 build
Replies: 1
Views: 3270

My son and I H1 build

here are some pictures of what my 9yr old son and I built. std H1 printer, custom box for electronics. Ryan suggested a stabilizer bar across the to of Z to keep machine from side to side jumping when making fast X travel, also had cool idea for mounting velleman controllers on front of case. I will ...

Go to advanced search