Search found 11 matches

by Michail1
Thu Nov 07, 2019 5:44 am
Forum: Troubleshooting
Topic: Rostock V4 - SE300 - Barrel fan not working.
Replies: 9
Views: 1708

Re: Rostock V4 - SE300 - Barrel fan not working. (Resolved)

Turns out the Duet Board was bad. Replaced under warranty... All good now.
by Michail1
Tue Oct 22, 2019 10:30 am
Forum: Troubleshooting
Topic: Display Upgrade (issue) - Firmware Upgraded - (Resolved)
Replies: 5
Views: 1175

Re: Display Upgrade (issue) - Firmware Upgraded - (Resolved)

Thank you. I saw that. I simply didn't (and still don't) have the original image to add to it. I may consider adding it the next time I update the firmware in both panels; however, since it's working now, I will leave it alone.

Thank you dc42.
by Michail1
Sat Oct 05, 2019 1:04 pm
Forum: Troubleshooting
Topic: Rostock V4 - SE300 - Barrel fan not working.
Replies: 9
Views: 1708

Re: Rostock V4 - SE300 - Barrel fan not working.

After my initial post and realizing it wasn't a simple problem, I put in a trouble ticket, but decided to continue with this thread so that others may follow to resolution in case they run into the same issue at some point in the future. They responded with performing the initial diags that I explai...
by Michail1
Fri Oct 04, 2019 7:41 pm
Forum: Troubleshooting
Topic: Rostock V4 - SE300 - Barrel fan not working.
Replies: 9
Views: 1708

Re: Rostock V4 - SE300 - Barrel fan not working.

I have confirmed that the purple wire is correctly connected to the Duet and is pin 1 on the 10pin connector. I confirmed there is continuity with a meter. I confirmed the 10pin socket (pin1) has continuity to the fan socket and that the other pin of the fan socket goes to ground. I have uploaded se...
by Michail1
Mon Sep 30, 2019 2:43 pm
Forum: Troubleshooting
Topic: Rostock V4 - SE300 - Barrel fan not working.
Replies: 9
Views: 1708

Re: Rostock V4 - SE300 - Barrel fan not working.

The fan freely rotates by finger.
I pulled and connected to a 12v supply and confirm that the fan works.

Will re-assemble when I get home to see if that was enough. Assuming the fan will not spin at that point though.
by Michail1
Sun Sep 29, 2019 8:24 pm
Forum: Troubleshooting
Topic: Rostock V4 - SE300 - Barrel fan not working.
Replies: 9
Views: 1708

Rostock V4 - SE300 - Barrel fan not working.

I have a V4 and V3.2 The V4 is less than a month old. Just ran into a problem in that the filament would stick in the barrel after a few MM of feed. Nearly impossible to pull out. So, it appears the filament is melting in the barrel. So, I discovered the barrel fan wasn't spinning. So, suggestions o...
by Michail1
Sat Sep 28, 2019 2:51 pm
Forum: Troubleshooting
Topic: Display Upgrade (issue) - Firmware Upgraded - (Resolved)
Replies: 5
Views: 1175

Re: Display Upgrade -- Completed with Features.

V3.2 has a 5" PanelDue v3 on Firmware 1.17a V4 has a 5" PanelDue v3 on Firmware 1.22.1(28b1) Since I can't find the Logo on boot, I will go with a NoLogo bin file. Following the directions linked by dc42, I only only needed to download one image. 'PanelDue-v3-5.0-nologo.bin' 118kb The current firmwa...
by Michail1
Sat Sep 28, 2019 2:56 am
Forum: Troubleshooting
Topic: Display Upgrade (issue) - Firmware Upgraded - (Resolved)
Replies: 5
Views: 1175

Re: Display Upgrade

I have confirmed that the macros are identical. Also, the firmware is identical on the Duet boards... Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet Firmware Electronics: Duet WiFi 1.02 or later Firmware Version: 2.04RC1 (2019-07-14b1) WiFi Server Version: 1.22 Web Interface Version: 1.22.6 ...
by Michail1
Sat Sep 14, 2019 12:41 pm
Forum: Troubleshooting
Topic: Display Upgrade (issue) - Firmware Upgraded - (Resolved)
Replies: 5
Views: 1175

Display Upgrade (issue) - Firmware Upgraded - (Resolved)

I have a V3.2 with LCD Display. It's ok. I just bought a V4 with LCD display and I noticed a few nice things. -example... LOAD/UNLOAD from the display on the V4 which on the V3.2 you must go back to the computer to click ok. Just the one example above makes me want to upgrade the V3.2 display to mat...
by Michail1
Sat Sep 14, 2019 11:53 am
Forum: Troubleshooting
Topic: Rostock v4 Error code M141
Replies: 4
Views: 1001

Re: Rostock v4 Error code M141

The upgrade from 4.1 to 4.2.1 is the cause of the problem. Take a look at the gcode files you're producing. You will notice a M141 S28 has been added by 4.2.1. You can either take out the M141 S28 completely or change it to M141 S0 To solve the problem completely, simply change the default in the so...
by Michail1
Sat Sep 14, 2019 11:41 am
Forum: New Member introduction
Topic: Hello From Everett, WA
Replies: 1
Views: 607

Hello From Everett, WA

It took many years to get me to purchase a 3D printer as I didn't know if I would use it enough to justify the cost. Friend convinced me just over a year ago to buy a SeeMeCNC. So, I bought the V3.2 Kit. It went nearly flawlessly. One one bad power supply which was replaced quickly in warranty. Not ...

Go to advanced search