Search found 9 matches
- Mon Oct 11, 2021 10:42 am
- Forum: Duet
- Topic: Duet2 RepRapFirmware v3.2.2 Upgrade
- Replies: 2
- Views: 5097
Re: Duet2 RepRapFirmware v3.2.2 Upgrade
Problem with the z-probe on Rostock Max v4. I've only had to probe once since the upgrade, super reliable, but now I find that my z-probe is stuck at a value of 1000, and won't activate any probes because it is already triggered. It seems to be a connection issue of some sort, as when I tap the boar...
- Sat Apr 01, 2017 10:31 pm
- Forum: Troubleshooting
- Topic: Trouble uploading firmware
- Replies: 2
- Views: 2893
Re: Trouble uploading firmware
I emailed Support on this issue and JJ suggested disconnecting the accelerometer and trying to upload again. I did that, and also didn't click the rear power button on until I was actually clicking upload at the same time. The reset button wasn't working for what people kept suggesting. Part of the ...
- Fri Mar 31, 2017 11:32 am
- Forum: Troubleshooting
- Topic: Trouble uploading firmware
- Replies: 2
- Views: 2893
Trouble uploading firmware
Hello, I think I've cocked up somewhere. I tried to upload a pre-compiled firmware (compiled in Arduino), and now the board will no longer reply to programming requests. The green light is on, there is a yellow light flashing very fast, and the Rx light also blinks. I'm at a loss for what to do next...
- Tue Mar 28, 2017 11:24 am
- Forum: RostockMAX v3
- Topic: New duel extrusion
- Replies: 22
- Views: 13521
Re: New duel extrusion
Hi Marcello, I'm using Simplify3D or Repetier/Cura. I don't have any problems with slicing. I did have problems with regular jams though. Normally, should start out with the 1st extruder selected and fed in. When the firmware receives a T1 or T0, it should automatically retract and feed the correct ...
- Mon Mar 20, 2017 12:56 pm
- Forum: RostockMAX v3
- Topic: New duel extrusion
- Replies: 22
- Views: 13521
Re: New duel extrusion
03162017. It created a loop. I removed the T1 and T0 from the select commands (because it creates a loop, freezing my printer, and shoving endless filament through the printer if you don't reset). The select extruder commands are triggered when the firmware received a T# command, then in the command...
- Sat Mar 18, 2017 4:24 pm
- Forum: RostockMAX v3
- Topic: New duel extrusion
- Replies: 22
- Views: 13521
Re: New duel extrusion
I was using the current dev dual extrusion firmware, and it created a loop where, when the tool change occurred, another tool change was initiated, and the printer just said there grinding filament and sounding angry. Have to remove the T0 and T1's from the Select Commands in the firmware. Would lov...
- Thu Mar 16, 2017 11:33 pm
- Forum: What are YOU making?
- Topic: Tri Hotend
- Replies: 160
- Views: 92004
Re: Tri Hotend
Hi, this thread looks dead, but I was curious if anyone has installed one of these on a Max v3 Rostock printer yet? Do you have to remove the i2c controller to make this work?
MatterHackers is still carrying these, and they still look amazing.
MatterHackers is still carrying these, and they still look amazing.
- Thu Mar 16, 2017 10:23 pm
- Forum: RostockMAX v3
- Topic: Changing the Hot End?
- Replies: 15
- Views: 12459
Re: Changing the Hot End?
Thanks for the reply, Djarmag.
- Tue Mar 14, 2017 10:43 pm
- Forum: RostockMAX v3
- Topic: Changing the Hot End?
- Replies: 15
- Views: 12459
Changing the Hot End?
I'm trying to figure out how to install a Volcano hotend on the Max v3. The hotend does not look very easy to swap, can't find any set screws to release to get the thing to drop out. I also have a high-temp heatbreak attachment I would like to be able to swap out in case I want to print with PET. I ...