Search found 22 matches

by felich
Sat Mar 21, 2020 6:54 pm
Forum: Artemis
Topic: XY dimensions are incorrect
Replies: 2
Views: 512

XY dimensions are incorrect

Is there a way to calibrate the XY dimensions?
Cura shows the correct dimensions but the print comes out shorter in both x and y directions.
Any ideas?
by felich
Sat Mar 21, 2020 6:50 pm
Forum: Artemis
Topic: static ip address
Replies: 2
Views: 590

static ip address

I have to go into another room to see what ip address Artemis received.
Is there any way to set a static ip address?
by felich
Sat Sep 28, 2019 2:46 pm
Forum: Artemis
Topic: Artemis 300 whiskers
Replies: 4
Views: 2014

Re: Artemis 300 whiskers

Will do.
Thanks!
by felich
Thu Sep 26, 2019 1:02 pm
Forum: Artemis
Topic: Artemis 300 whiskers
Replies: 4
Views: 2014

Re: Artemis 300 whiskers

I'm printing with PLA from SeeMeCNC item #50146.
Here are the pertinent Cura 4.3 settings.
Right click on the image and "open link in a new tab" then click on the image.
by felich
Wed Sep 25, 2019 4:46 pm
Forum: Artemis
Topic: Artemis 300 whiskers
Replies: 4
Views: 2014

Artemis 300 whiskers

I have been getting whiskers in some of my prints. I am using Cura 4.3 but got them on 4.2x also. This photo shows a print that just goes around the edges with 100% fill so I would not expect the extruder to need to move across the print. I'm sure it is some setting in Cura, but I don't have a clue....
by felich
Wed Sep 25, 2019 4:11 pm
Forum: Artemis
Topic: Artemis 300 RTP
Replies: 5
Views: 1004

Re: Artemis 300 RTP

Thanks.
It was that easy.
by felich
Tue Sep 24, 2019 12:48 pm
Forum: Artemis
Topic: Artemis 300 RTP
Replies: 5
Views: 1004

Re: Artemis 300 RTP

You are right about the code. There is an M84 near the end of the listing. This wasn't an issue with my other Artemis. Editing it out fixes the problem, but if I forget I get a ruined print. The 300's steppers don't seem to have enough holding power to keep the head homed after cutting power to the ...
by felich
Mon Sep 23, 2019 7:51 pm
Forum: Artemis
Topic: Artemis 300 RTP
Replies: 5
Views: 1004

Artemis 300 RTP

I'm concerned about an issue that surfaced on my Artemis 300 right after I updated my Cura to 4.2.1 After every print job the extruder sags down and jams its hotend into the finished print. Also, when I power off the printer the extruder sags down to the bed. My other Artemis doesn't do that. Is thi...
by felich
Tue Jun 12, 2018 7:56 pm
Forum: Artemis
Topic: HEATER 1 Fault
Replies: 4
Views: 2184

Re: HEATER 1 Fault

I am not satisfied with wiggling wires to make it work for a while. I am making large prints that each use up $20 of filament. I have to start each print with a full roll so an aborted print is not just a waste of my time. The heater connector looks under rated for the current it carries. I am think...
by felich
Wed Jun 06, 2018 6:40 pm
Forum: Artemis
Topic: HEATER 1 Fault
Replies: 4
Views: 2184

HEATER 1 Fault

Artemis was printing away (using PETG) at 250 degrees when the hotend temperature plot went through very rapid plus and minus 30 degree swings and then threw a "Heater 1 Fault" and shut down the heater. I cycled the power on Artemis and restarted my print with no faults. Now I worry that i...
by felich
Wed May 02, 2018 4:46 pm
Forum: Development Topics
Topic: Artemis Browser Interface
Replies: 5
Views: 6036

Re: Artemis Browser Interface

I don't see it. Please point it out.
Screen Shot.jpg
by felich
Tue May 01, 2018 2:31 pm
Forum: Development Topics
Topic: Artemis Browser Interface
Replies: 5
Views: 6036

Artemis Browser Interface

I could not find a place in the forum specifically for software change requests, so I hope this a good place to put this thread. I have what I feel is an important request. Please add the file date to the information shown in the G-Code file listing. I am never certain that I have the latest G-Code ...
by felich
Wed Jan 17, 2018 8:14 pm
Forum: Artemis
Topic: First Probe
Replies: 3
Views: 855

Re: First Probe

wepollock, Most Excellent, Thanks. Your macro was a big help. I got down to -.35. Now my G0Z0 comes out perfect! So in the Configuration Guide Step Five where is says "If it's too loose, run the following GCode: "G31 P500 X0 Y0 Z-0.25"" I believe it should say "If it is too ...
by felich
Wed Jan 17, 2018 6:24 pm
Forum: Artemis
Topic: First Probe
Replies: 3
Views: 855

First Probe

I have moved on to the First Probe. After calibration I did a GoZo with a piece of printer paper on the bed. The tip comes down slowly and then there is a "tink" as it stops. The paper is held so tightly that it tears when moved. So I ran another First Probe and then another. The tip still...
by felich
Wed Jan 17, 2018 6:04 pm
Forum: Artemis
Topic: First batch of Artemis is out the door.
Replies: 6
Views: 1667

Re: First batch of Artemis is out the door.

SD chip wasn't seated properly.
AOK now.
by felich
Wed Jan 17, 2018 5:39 pm
Forum: Artemis
Topic: No joy with browser connection
Replies: 19
Views: 4954

Re: No joy with browser connection -Solved now!

Well I unmounted the controller and removed the SD chip and looked at it on my PC. Everything looked OK far as I could tell. I remounted the controller and inserted the SD chip. BAM! The web page loaded first try. So I guess the SD chip was not inserted to its satisfaction, but re-inserting it made ...
by felich
Tue Jan 16, 2018 1:53 pm
Forum: Artemis
Topic: First batch of Artemis is out the door.
Replies: 6
Views: 1667

Re: First batch of Artemis is out the door.

I am the guy that received the RTP.
I am having no luck seeing the web page.
Please see my post "No joy with browser connection"
Thanks for any help you can provide.
by felich
Tue Jan 16, 2018 1:38 pm
Forum: Artemis
Topic: No joy with browser connection
Replies: 19
Views: 4954

Re: No joy with browser connection

Here is the latest information on this issue: I shut down the WiFi with M552 S0 I re-sent M587 with S"studio" P"password" I10.0.0.89 J10.0.0.1 K255.255.255.0 Then: m552 S1 ok m552 WiFi module is connected to access point studio, IP address 10.0.0.89 ok m553 Net mask: 255.255.255....
by felich
Mon Jan 15, 2018 9:47 pm
Forum: Artemis
Topic: No joy with browser connection
Replies: 19
Views: 4954

Re: No joy with browser connection

Where do I find the Artemis documentation?
by felich
Sun Jan 14, 2018 6:29 pm
Forum: Artemis
Topic: No joy with browser connection
Replies: 19
Views: 4954

Re: No joy with browser connection

I shut down Artemis and still got a reply from pinging 10.0.0.232 so it looks like a DHCP issue. However, I don't know which machine is using 10.0.0.232 so I can't change it on that end. Is there a way to set a static IP address on Artemis? Also, where can I find all of these mysterious M codes you ...
by felich
Fri Jan 12, 2018 6:03 pm
Forum: Artemis
Topic: No joy with browser connection
Replies: 19
Views: 4954

Re: No joy with browser connection

I don't see anything about RSSI. Used output buffers: 1 of 32 (9 max) === Platform === RepRapFirmware for Duet WiFi version 1.19.2 running on Duet WiFi 1.0 Board ID: 08DGM-95BNL-MGPSJ-6JKFG-3SJ6Q-T1W7Y Static ram used: 21176 Dynamic ram used: 95552 Recycled dynamic ram: 2056 Stack ram used: 4056 cur...
by felich
Fri Jan 12, 2018 5:16 pm
Forum: Artemis
Topic: No joy with browser connection
Replies: 19
Views: 4954

No joy with browser connection

I just plugged in my RTP Artemis and went through the Configuring Artemis procedure. Wifi enables fine. YAT reports: ok<LF>Wifi module is connected to access point studio, IP address 10.0.0.232<LF> Step 3 says:Open a new tab and enter the IP Address of your printer. When the page loads, click on &qu...

Go to advanced search