Search found 454 matches

by dc42
Fri Apr 16, 2021 3:11 pm
Forum: Artemis
Topic: New Artemis setup issues
Replies: 6
Views: 5564

Re: New Artemis setup issues

I suspect it's because horizontal scrolling in input boxes has not been implemented.
by dc42
Sun Oct 11, 2020 4:39 am
Forum: RostockMAX v4
Topic: Boro Glass Build Plate vs FabLam Flex
Replies: 2
Views: 3724

Re: Boro Glass Build Plate vs FabLam Flex

Yes, PETG can bond too well to glass, see https://www.youtube.com/watch?v=Ro3CdQQUiKo. When using glass beds, I print on ordinary float glass, not borosilicate. It costs much less and I can get my local glass supplier to cut pieces the right size for me. It's important to have the sharp edges smooth...
by dc42
Sun Oct 11, 2020 4:34 am
Forum: The Build Zone
Topic: ANY V4 Build Experts??? I was good till calibration - need help
Replies: 1
Views: 8182

Re: ANY V4 Build Experts??? I was good till calibration - need help

It sounds as though you haven't entered the details of your access point through YAT using the M587 command.
by dc42
Sun Oct 11, 2020 4:31 am
Forum: Troubleshooting
Topic: Firmware error every time I start printing on the machine
Replies: 14
Views: 8810

Re: Firmware error every time I start printing on the machine

Now the machine loads with a warning on the screen telling me that the heightmap was loaded before the z=0 datum, which was not determined during probing and might lead to an offset. That's a warning that you have loaded a height map but the Z=0 position has been determined from the endstop switche...
by dc42
Sun Oct 11, 2020 4:29 am
Forum: Troubleshooting
Topic: Firmware error every time I start printing on the machine
Replies: 14
Views: 8810

Re: Firmware error every time I start printing on the machine

Well, it works in getting rid of that but now I have this; G0/G1: target position not reachable from current position My prints are all cancelling before they start. Starting script: G28 ; home all axes M564 S0 H0; Set axis limits, forbid movement outside unhomed axis, allow movement outside bounda...
by dc42
Fri Aug 14, 2020 8:54 am
Forum: Troubleshooting
Topic: Firmware error every time I start printing on the machine
Replies: 14
Views: 8810

Re: Firmware error every time I start printing on the machine

Please upgrade to firmware 2.05.1 and see if the problem is still present.
by dc42
Fri Aug 14, 2020 8:46 am
Forum: Artemis
Topic: static ip address
Replies: 2
Views: 3921

Re: static ip address

You can set a static IP address using M587 if using a Duet WiFi, or M552 if using Duet Ethernet. But many people use an address reservation on the router instead.
by dc42
Fri Aug 14, 2020 8:45 am
Forum: Artemis
Topic: XY dimensions are incorrect
Replies: 2
Views: 3669

Re: XY dimensions are incorrect

If the scaling is consistent, you can use a M579 command in config.g to correct for small scaling errors. To check the scaling is consistent, print a large noughts-and-crosses/tic-tak-toe pattern on the bed, and check that the lines are straight.
by dc42
Fri Aug 14, 2020 8:42 am
Forum: Artemis
Topic: Enable Auto-Sleep parks print head on part
Replies: 4
Views: 4941

Re: Enable Auto-Sleep parks print head on part

Some delta printer owners use a retractor to apply enough upwards force on the effector or on the Bowden tube to prevent the effector dropping when the motors are turned off.
by dc42
Thu Jan 23, 2020 8:07 am
Forum: Troubleshooting
Topic: Why doesn't this print a circle?
Replies: 4
Views: 3691

Re: Why doesn't this print a circle?

The attachment is no longer available, so I can't look at it.
by dc42
Tue Oct 22, 2019 9:10 am
Forum: Troubleshooting
Topic: Display Upgrade (issue) - Firmware Upgraded - (Resolved)
Replies: 5
Views: 4839

Re: Display Upgrade (issue) - Firmware Upgraded - (Resolved)

If you do want to add a logo when PanelDue starts up, the instructions for doing so are at https://github.com/dc42/PanelDueFirmwar ... /Readme.md.
by dc42
Sat Sep 14, 2019 5:58 pm
Forum: KISSlicer
Topic: V4 / Duet2 / KISSlicer / DUAL EXTRUSION Y-bowden FEED and RETRACT?
Replies: 2
Views: 10307

Re: V4 / Duet2 / KISSlicer / DUAL EXTRUSION Y-bowden FEED and RETRACT?

You can do the retract/load either in the slicer tool change scripts, or in the Duet tool change files. If you do it in the Duet tool change files, it should work for all slicers.
by dc42
Sat Sep 14, 2019 5:55 pm
Forum: Troubleshooting
Topic: Display Upgrade (issue) - Firmware Upgraded - (Resolved)
Replies: 5
Views: 4839

Re: Display Upgrade

See https://miscsolutions.wordpress.com/paneldue/. However, I suspect the load/unload commands are just macros, so I suggest you first compare the contents of the /macros folder on the SD card of your V3.2 with the same folder on your V4.
by dc42
Fri Sep 13, 2019 11:56 am
Forum: RostockMAX v4
Topic: Ghosting on vertical surfaces
Replies: 13
Views: 10946

Re: Ghosting on vertical surfaces

Dynamic Acceleration Adjustment can help with ringing (the cause of ghosting) on some machines. See https://duet3d.dozuki.com/Wiki/Gcode#Section_M593_Configure_Dynamic_Acceleration_Adjustment. There are also some threads about it on the Duet3D forum. But it's better to reduce ringing by mechanical m...
by dc42
Fri Sep 13, 2019 11:51 am
Forum: Artemis
Topic: sudden under-voltage barrage.
Replies: 4
Views: 4906

Re: sudden under-voltage barrage.

I don't know what PSUs SeeMeCNC supplies with the Artemis, but it it has a 115V/230V selector switch and your mains is 115V, check that the switch isn't set to 230V.
by dc42
Fri Sep 13, 2019 11:49 am
Forum: Other Machines
Topic: Free Leapfrog CreatrHS - What should I do with it?
Replies: 4
Views: 6739

Re: Free Leapfrog CreatrHS - What should I do with it?

A Duet could power that Z motor directly.
by dc42
Fri Sep 13, 2019 3:23 am
Forum: Duet
Topic: Duet 3 now shipping
Replies: 0
Views: 7205

Duet 3 now shipping

In case you missed it, we've started shipping Duet 3 main boards. The Duet 3 MB6HC has: Six high current stepper motor drivers, good to about 6A peak/4A RMS One high current output (intended for bed heater) and three medium current outputs (intended for hot end heaters) Three 4-wire can outputs and ...
by dc42
Mon Jul 08, 2019 3:12 pm
Forum: Troubleshooting
Topic: Max v2 issue with peaks and valleys in bed map[NEW DATA]
Replies: 58
Views: 40199

Re: Max v2 issue with peaks and valleys in bed map

Try moving to X0 Y0, then to X100 Y0, then measure the Z probe trigger height a few times. Then move to X<max> Y0, then X100 Y0, and re-measure the trigger height. That will show up the backlash.
by dc42
Tue Jul 02, 2019 8:36 am
Forum: Troubleshooting
Topic: Max v2 issue with peaks and valleys in bed map[NEW DATA]
Replies: 58
Views: 40199

Re: Max v2 issue with peaks and valleys in bed map

Ridges along the X axis that turn into valleys at the other end is a classic sign of backlash in the mechanics. They appear because RRF probes along the X axis in opposite directions in alternate passes. With backlash, the exact nozzle height at a particular point depends on the direction in which y...
by dc42
Tue Jun 25, 2019 4:18 pm
Forum: Troubleshooting
Topic: Best upgrade investment?
Replies: 10
Views: 7539

Re: Best upgrade investment?

I use a 330mm diameter x 5mm thick aluminium bed plate with a 300mm diameter AC mains heater on my delta, and that works well. So a 280mm diameter heater should work for you, as long as the bed plate is thick enough to spread the heat well. My delta uses a 24V 5A PSU. With the bed heater being AC ma...
by dc42
Wed May 22, 2019 2:13 am
Forum: RostockMAX v3.2
Topic: V3 to 3.2 : DUET v. SMCNC connectors?
Replies: 2
Views: 4666

Re: V3 to 3.2 : DUET v. SMCNC connectors?

SMCNC sold out on DUETs so I shopped elsewhere. DUET connectors are warned against in V3.2 assembly walkthrough: When inserting the wires in the white Molex KK connectors, make sure you're using the connectors we sent you in the kit, NOT the ones included in the Duet box! I'm guessing this is becau...
by dc42
Fri May 10, 2019 3:51 pm
Forum: RostockMAX v3
Topic: V3 conversion to WASP LDM Clay extruder process
Replies: 11
Views: 9812

Re: V3 conversion to WASP LDM Clay extruder process

DUET WiFi option: I use my cell phone to hotspot for WiFi; that's how I'm typing now, and I'll be on our closed WiFi-LAN in our shop where I get full (cell)bars through concrete. Somewhere in the gazillion forum posts on the DUET WiFi board I recall reading that the WiFi was unstable? Is this true,...
by dc42
Fri May 10, 2019 3:48 pm
Forum: RostockMAX v3
Topic: V3 conversion to WASP LDM Clay extruder process
Replies: 11
Views: 9812

Re: V3 conversion to WASP LDM Clay extruder process

If you go with the Duet, you'll end up with a much better printer. That being said, I have no idea how you'd integrate a BL Touch with a Duet controller. Using BLTouch with Duet is covered in the wiki at https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_BLTouch. However, on a delta I advi...
by dc42
Fri Apr 12, 2019 2:53 am
Forum: Troubleshooting
Topic: WiFi dropout - how to reconnect?
Replies: 16
Views: 12658

Re: WiFi dropout - how to reconnect?

Duet Web Control displays the version numbers on the Settings page. You can also get the main firmware version using M115 and the WiFi firmware version from the M122 diagnostic report.
by dc42
Thu Apr 11, 2019 5:50 pm
Forum: Troubleshooting
Topic: WiFi dropout - how to reconnect?
Replies: 16
Views: 12658

Re: WiFi dropout - how to reconnect?

Which main and WiFi firmwares are you running? 2.02 main and 1.23 WiFi are recommended. Main firmware 2.02 retries automatically if the WiFi connection is lost.

Go to advanced search