Welcome to the SeeMeCNC Community

If it's going wifi will the wifi config be available from the due, I change my password regularly and having to plug it direct to the computer everytime would be a pita The current plan is that you will only be able to change passwords by removing the SD card and putting it into a PC. But we're ope...

If it's going wifi will the wifi config be available from the due, I change my password regularly and having to plug it direct to the computer everytime would be a pita

Would it be possible to redo the fan plate so that it accepts two fans? As I was fairly disciplined when I created the sketch, so it didn't take long, I have done this. The fans had to go where they are to stay inside the supports and I have placed so they are nearer the head and bed FETs. Be aware...

Another thank you DC. I also have your IR sensor and it is a great solution, works flawlessly

I just installed this today, and it fits great. Thanks for the great design. I thought I'd point out that you have to take off the bottom of the printer to remove the melamine bracket feet and install the plastic rails. At least, I couldn't see any other way to do it. I just snapped them off as I c...

Did you learn anything?

Personally think 24v is a bit excessive. Todays plan is to hook the bed up to a variable psu and wind it up until the bed equalises at about 130 maybe 140. I reckon this will be about 14 - 15v. It might not warm up as fast as higher voltage but if the driving ssr fails its a built in limiter. I reck...

Thanks, I still can't find exactly what I'm looking for, but i think Ive more or less figured it out. Could do with a table instead of 25 resistance and beta, as the beta changes quite considerably across the range. Or, if not a table specify r at a selectable point say 190 and then work out beta ac...

Does anyone know the actual maths behind this. Specifically H & L effect and what points they act on.

I cannot find this info anywhere

In theory E3D V6 should be the same settings as stock hotend. They have same thermistor according to specs.

Fits the 4.3" alternative LCD as supplied by Think3DPrint3D
Fits to the existing LCD plate.

http://www.thingiverse.com/thing:1446641" onclick="window.open(this.href);return false;

I started with your files, thank you.

An interesting note, I have no idea why, but I am using the diff IR probe and the 6 factor calculation threw everything a mile out. I changed it to 7 and it's working beautifully.

Couldn't find an internal mount so I made this.
Just remove the front Rambo board clips and then it all just clips in, I don't know if it needs the fan but it can't harm.

http://www.thingiverse.com/thing:1429433" onclick="window.open(this.href);return false;

Hmm, you did precede it with the parameter ID "P" correct? It should look like this: M551 Popensesame Where the password is opensesame This works on all of my Duets, I get a password prompt when I try to access via the Duet Web Control. ermm no P .... I'll get there lol Thank you

Great_Thark wrote:

mhackney wrote:Look at the top of config.g - username and password. The comment says for FTP but it also applies to the web interface.

Ta

So I eventually got round to checking this, I didn't miss it, i've put a password in but it doesnt ask just logs on

mhackney wrote:Look at the top of config.g - username and password. The comment says for FTP but it also applies to the web interface.

Ta

I must have missed something. Never saw any way to have login credentials. Atm using remote desktop to a local machine but its a bit of a klutzy solution.

This is good stuff. The whole bosac thing was a pain (i had a wrong version initially) in fact the whole web interface is great work.
Do you know if there is any intention to add a login option so you can access remotely without letting everyone else access your printer.

Thanks for the quick response.
I've just ordered the duet. Is the crishamm fork of the dc42 reprap firmware the one to go with then?

Awesome. Any chance of an idiots guide for how to do this.