Welcome to the SeeMeCNC Community

geneb wrote:
Is the hot end set to the correct temperature for the filament you're using?

g.

Yes - 220 degrees - using PLA from SeeMeCNC

I'm sure there is a way to resolve this but I'm stumped

Thank you

When I load the filament you can see the filament going from ~1 inch beyond the EZR Struder to inside the hot end . . . then the clicking sound at the EZR Struder . . . and no melted filament comes out of the hot end - nothing, not even a tiny bit I checked the connector at the hot end - seems good,...

Maybe I should take up another hobby . . . having the patience and understanding required to make these machines work well doesn't come naturally for me . . .

But I do appreciate the help and suggestions

Thank you geneb & Mac The Knife!

I will make an effort to do this and get this thing up and running - when it works, it really does a great job

I realize the ERIS has been discontinued however, is there any possibility of obtaining an ERIS build document?

Thanks again!

My ERIS is totally messed up - again - this is incredibly frustrating as I am on vacation for four more days and I really wanted to finish a small project before I have to go back to work I replaced the hotend - seemed easy enough - I made sure the tube guiding the filament was seated into the botto...

geneb wrote:Yep, that's the beastie.

Thanks - it's on the way!

Another modification I recommend is the 29A power supply kit - it's a big improvement over the ATX supply. Good luck! g. Thank you geneb & Xenocrates Is this the power supply you recommend --> https://www.seemecnc.com/products/12-volt-29-amp-dc-power-supply-kit If so, I'll order it - anything e...

Okay . . . here I go again . . . resuming the process of completing my Rostock MAX™ v2 Desktop 3D Printer Kit I have received permission to use the dining room table next week (because I have no air conditioning in the garage - thank you Ms. Sand) The partially assembled printer is now on the dining...

I realize this is not SeeMeCNC's fault but the USPS Priority Mail shipment of my new hotend was supposed to be delivered on Thursday - now for some reason it's in a USPS facility 55 miles away with no mention of when it will be delivered - none :( I've experienced two similar (but not this bad) expe...

Mac The Knife wrote: That is if you're installing a stock hotend.

The current and new hotend are from SeeMeCNC for the ERIS so I hope it goes well

It would be nice to have a document to guide through the process - maybe I'll make one

Thank you

I designed a very small tracked vehicle using two very small continuous rotation servos Then I created a new CAD model from scratch I printed all the parts and discovered a design flaw :oops: (ha, we've all been there, eh) As I began printing the new parts my ERIS printer went crazy - I have a new h...

Okay - they are on order - I think I ordered the correct items

Thank you!

Did you grab the injection molded carriages as well?

No - I'll order those - anything else I should get with that order?

Thank you

After taking a while from this build, I'm back and I am ready to continue I've had this machine in the garage for . . . way too long . . . I did purchase and receive the updated arms When I stopped building it, the top was installed so, yes, I still have a long way to go I'm only posting this for tw...

I'm in Powder Springs but I haven't completed my ROSTOCK MAX™ V2 yet - it's probably ~70% completed

My Eris printer is doing a great job though

FOUND IT - sorry

It's really not my fault - my daughter moved the Eris printer to the bonus room, then my wife moved it from there to the bedroom. I have looked EVERYWHERE but I can't find the power supply but I may have one on hand that will do the job If anyone can tell me where to find the specifications for the ...

. . . changes, changes, changes . . .

Ready to test the rotational functionality of this little machine . . . always fun to make a little progress . . .

Typical with many . . . probably most . . . of my designs, I encountered too many problems Each was "solvable" but collectively, well, sometimes you just know it's time to rip out "Plan B" (ha) One question (which, I should probably post somewhere else but . . . ) I'm not having ...

I want everyone to understand, there was nothing wrong with my ROSTOCK MAX™ V2 While I was completing the build of the Rostock printer I encountered a catastrophic event but this was not related to 3D printing - this event put my life on hold but now, things are much better, I'm closer to being &quo...

This may not work but I'm going to create a prototype of a turntable platform for stop-motion photography I plan on using this turntable from the local home-improvement store I will be using this 24-tooth fixed gear - I guess this would be the "sun gear" as the "planet gear" will...

I'm printing the calibration box right now - so exciting!

Okay, that was easy - the connector wasn't plugged into the print head component Most of you will probably hate me - I'm not very smart - apologies up front I'm not sure what's "wrong" with me . . . so far, I've endured life knowing my destiny lies far from the top . . . so I focus on stuf...

I'm having a few problems getting my Eris printer working (see attached)

Any help will be greatly appreciated

Thanks

Tonight I purchased an ERIS Delta I'm excited about this - it will be in my office at work I teach Engineering Graphics (and a few other courses) at the local university and I'm looking forward to being able to provide students with examples of 3D printed parts We have a very nice 3D printing lab do...