Search found 10 matches

by dseebauer
Fri Oct 12, 2018 11:16 am
Forum: Rostock MAX v2
Topic: 091 Firmware pause for filament out
Replies: 3
Views: 2999

Re: 091 Firmware pause for filament out

Thanks for the reply. I have given up on this for the time being. Here is what I have determined though. The SeeMeCNC branch of the the FW (0.92.2) does not incorporate jam detection handling that the Repetier branch has (circa 0.92.9 or so). My guess is it branched or was modified before any of tha...
by dseebauer
Mon Oct 08, 2018 4:37 pm
Forum: Rostock MAX v2
Topic: 091 Firmware pause for filament out
Replies: 3
Views: 2999

Re: 091 Firmware pause for filament out

So according to the Repetier forum, Jam detection was added in v0.92. The current firmware on the SeeMeCNC github is 0.92.2 Looking at the configuration file for 0.92.2, I see that for a V2, it uses values assuming it was upgraded/built using the ball cup arms and injection molded carriages, etc. Fo...
by dseebauer
Sun Oct 07, 2018 12:28 pm
Forum: Rostock MAX v2
Topic: 091 Firmware pause for filament out
Replies: 3
Views: 2999

091 Firmware pause for filament out

Hi, This may have been discussed before but I could not find a reference. I want to add a filament out sensor to my stock V2, and have read that it can be wired to a spare endstop connector on the RAMBO. Does anyone know if the 091 firmware will support a pause and hopefully park on getting a signal...
by dseebauer
Wed Jul 25, 2018 11:07 pm
Forum: Troubleshooting
Topic: TPU Fail or no?
Replies: 1
Views: 698

TPU Fail or no?

Hi All, I was recently trying to print some TPU for the first time. Well I did print a couple calibration cubes when I first got it, but then it sat around a for a while. The first cube I printed was great (for a cube anyway). The layering was nice and the resin was some what clear (translucent gree...
by dseebauer
Fri Feb 16, 2018 12:44 pm
Forum: Rostock MAX v2
Topic: Warped Onyx Board V2
Replies: 3
Views: 1520

Warped Onyx Board V2

Hi all, I recently have had a lot of trouble getting consistent first layers on my V2 and tracked it down as best I could to a warped heated bed. I never really had great success with the printer despite the hours or trouble shooting, so this may have been the culprit all along. It just got much wor...
by dseebauer
Sun Mar 19, 2017 11:22 am
Forum: Rostock MAX v2
Topic: New Power Supply / Opening the Bottom
Replies: 27
Views: 7112

Re: New Power Supply / Opening the Bottom

I have the same issue. My machine is about the same age as yours and I have been scratching my head trying to figure out how to make it happen. I like the idea of using the extra side plate. Thanks for the tip.

Dave
by dseebauer
Fri Oct 03, 2014 12:10 pm
Forum: FAIL HAPPENS ! ! !
Topic: Arghh! ABS is so hrd!
Replies: 11
Views: 4174

Re: Arghh! ABS is so hrd!

Ok so I am learning more with every attempted print. Thanks to everyone that has weighed in here. I really appreciate it. I have been starting to get back on track with ABS prints using all of the advice that I've been given. Although it is still very finicky, here are the three key elements that re...
by dseebauer
Thu Sep 25, 2014 11:38 am
Forum: FAIL HAPPENS ! ! !
Topic: Arghh! ABS is so hrd!
Replies: 11
Views: 4174

Re: Arghh! ABS is so hrd!

Well, i tried the ABS juice. I could not find a consistent recipe out there. So my early attempts had the mix to thick, and made a mess of the glass. Still haven't been able to clean it up properly. In the end after many cleanings of the glass and re-applications, and cleaning a suspected clogged no...
by dseebauer
Sat Sep 13, 2014 10:05 pm
Forum: FAIL HAPPENS ! ! !
Topic: Arghh! ABS is so hrd!
Replies: 11
Views: 4174

Re: Arghh! ABS is so hrd!

Thanks for the advice and encouragement. I'll try some ABS juice and see if I can get the adhesion better. It has been as you said. Bigger the parts get the more trouble it is. If I understand it correctly, raft will put some space between the part and the bed? I presume to give it some forgiveness ...
by dseebauer
Fri Sep 12, 2014 6:12 pm
Forum: FAIL HAPPENS ! ! !
Topic: Arghh! ABS is so hrd!
Replies: 11
Views: 4174

Arghh! ABS is so hrd!

I've been trying to get a few ABS pieces printed for days now and all I get is stuff like this (ABS Spaghetti!) Seriously though, all my ABS prints seems to have same problems. Skirt/brim constantly lift and bubbles, or cracks form in the layers. Very frustrating! I'm running with the following sett...

Go to advanced search