1- Instalação do XP (ok).
2 -Test the parallel port (ok).
[youtube]http://www.youtube.com/watch?v=5zZz9-8rPuY[/youtube]
Search found 62 matches
- Fri Jul 06, 2012 11:33 pm
- Forum: Mach3 Software
- Topic: Configuration (H1-4x SeeMecnc) for Mach3
- Replies: 23
- Views: 25194
- Fri Jul 06, 2012 8:26 am
- Forum: Troubleshooting
- Topic: Stuck with Mach 3
- Replies: 6
- Views: 10026
Re: Stuck with Mach 3
Hi midget214, The problem could be setting the parallel port (off board). To solve this problem I tried to use a dot matrix printer and check if it works. The dot matrix printer ran successfully. But, I think it might be conflicting with some other operating system (Windows XP) or Mach3 settings. I ...
- Fri Jul 06, 2012 8:26 am
- Forum: Mach3 Software
- Topic: Configuration (H1-4x SeeMecnc) for Mach3
- Replies: 23
- Views: 25194
Re: Configuration (H1-4x SeeMecnc) for Mach3
Hi awander, I did the setting of the photo of the topic, but it still fails. First I need to try without the changes in plate 4 axes. Hi midget214, The problem could be setting the parallel port (off board). To solve this problem I tried to use a dot matrix printer and check if it works. The dot mat...
- Thu Jul 05, 2012 9:32 pm
- Forum: Mach3 Software
- Topic: Configuration (H1-4x SeeMecnc) for Mach3
- Replies: 23
- Views: 25194
Re: Configuration (H1-4x SeeMecnc) for Mach3
I tried setting http://forum.seemecnc.com/viewtopic.php?f=22&t=49 forum, but the engines remained locked. There is no movement when adjusting Mach3 axes (eg x +5, y +10, z +1 ... etc..)
- Thu Jul 05, 2012 8:49 pm
- Forum: Mach3 Software
- Topic: Configuration (H1-4x SeeMecnc) for Mach3
- Replies: 23
- Views: 25194
Configuration (H1-4x SeeMecnc) for Mach3
Hello, I need to start setting up the printer by Mach3(calibration). I would get a basic configuration developed by members of SeeMecnc and guidelines for the initial 4-axis card (no changes). I read the manual Mach3, but I could not put the printer to work. I need step by step guidance for H1 SeeMe...
- Wed Jul 04, 2012 7:52 am
- Forum: Temperature control devices
- Topic: Schematic for Velleman MK138 Temperature Controller Board
- Replies: 25
- Views: 30251
Re: Schematic for Velleman MK138 Temperature Controller Boar
The video shows a test I did with the changing MK138 (resistor R5) to 10K. According to the electronic manual SeeMecnc H1.
[youtube]http://www.youtube.com/watch?v=vmIlubEb8F8[/youtube]
[youtube]http://www.youtube.com/watch?v=vmIlubEb8F8[/youtube]
- Wed Jul 04, 2012 7:45 am
- Forum: Temperature control devices
- Topic: Schematic for Velleman MK138 Temperature Controller Board
- Replies: 25
- Views: 30251
Re: Schematic for Velleman MK138 Temperature Controller Boar
The goal is to adjust the value near 200 ° C.
- Tue Jul 03, 2012 7:42 am
- Forum: The Build Zone
- Topic: Help - My SeeMeCNC H-1 4ex.
- Replies: 5
- Views: 4776
Re: Help - My SeeMeCNC H-1 4ex.
Hello,
I need to start setting up the printer by Mach3. I would get a basic configuration developed by members of SeeMecnc and guidelines for the initial 4-axis card (no changes). I'll start a forum thread for Mach3.
thank you
Charles
I need to start setting up the printer by Mach3. I would get a basic configuration developed by members of SeeMecnc and guidelines for the initial 4-axis card (no changes). I'll start a forum thread for Mach3.
thank you
Charles
- Wed Jun 20, 2012 6:18 pm
- Forum: The Build Zone
- Topic: Extrude3D's H-1 Build
- Replies: 8
- Views: 7293
Re: Extrude3D's H-1 Build
My kit arrived on May 31 at the time of the academic tests. However, my work is already well advanced. Now comes the part of Mach3 and settings that can be more complex. Good job to all.
- Wed Jun 20, 2012 5:55 pm
- Forum: The Build Zone
- Topic: Help - My SeeMeCNC H-1 4ex.
- Replies: 5
- Views: 4776
Re: Help - My SeeMeCNC H-1 4ex.
Thank you John. Results of the setting temperature (198 ° C to 208 ° C, video VA). Is it good? I will control the motor (4EX) as suggested with Mach3.
[youtube]http://www.youtube.com/watch?v=vmIlubEb8F8[/youtube]
[youtube]http://www.youtube.com/watch?v=vmIlubEb8F8[/youtube]
- Wed Jun 20, 2012 12:41 pm
- Forum: The Build Zone
- Topic: Help - My SeeMeCNC H-1 4ex.
- Replies: 5
- Views: 4776
Help - My SeeMeCNC H-1 4ex.
Hello, I am new to this area of CNC (seeMeCNC I bought the kit) and I need help. I do not know what changes have to do on board 4-axis machine work. What should the temperature setting on the thermostat to melt the ABS plastic? thank you My printer: [youtube]http://www.youtube.com/watch?v=Snc6dAgOi6...
- Sat Apr 28, 2012 10:11 pm
- Forum: New Member introduction
- Topic: Olá
- Replies: 0
- Views: 1967
Olá
Estou iniciando o estudo da SeeMeCNC e quero motar uma impressora 3D.
Parabéns pela iniciativa da SeeMeCNC. Sucesso para todos.
Parabéns pela iniciativa da SeeMeCNC. Sucesso para todos.