{
    "BedTemp": 60,
    "BedTempEnabled": true,
    "BrimCount": 2,
    "BrimEnable": false,
    "DrawSpeed": 30,
    "EFactor_HShell": 1,
    "EFactor_Infill": 1,
    "EFactor_InnerHair": 1,
    "EFactor_Loop": 1,
    "EFactor_OuterHair": 1,
    "EFactor_Perimeter": 1,
    "EFactor_Raft": 1.6899999380111694,
    "EFactor_Skirt": 2,
    "EFactor_SoftSupport": 0.5,
    "EFactor_Support": 1,
    "ExtruderSpeedRatio": 100,
    "ExtrusionWidth": 0.5,
    "FFactor_HShell": 1,
    "FFactor_Infill": 1,
    "FFactor_InnerHair": 1,
    "FFactor_Loop": 1,
    "FFactor_OuterHair": 1,
    "FFactor_Perimeter": 1,
    "FFactor_Raft": 1,
    "FFactor_Skirt": 1,
    "FFactor_SoftSupport": 1.5,
    "FFactor_Support": 1.5,
    "FanEnable": true,
    "FanFirstLayer": 0,
    "FanN": 5,
    "FanNthLayer": 50,
    "FanSecondLayer": 50,
    "FilamentDiameter": 1.7599999904632568,
    "FirstLayerDrawSpeed": 15,
    "FirstLayerExtruderSpeedRatio": 100,
    "FirstLayerHeight": 0.30000001192092896,
    "GCodeFooter": "M104 S0  ;extruder heater off\nM140 S0  ;heated bed heater off (if you have it)\nM107       ;turn the layer fan off\nG91         ;relative positioning\nG1 E-1 F300  ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-5 ;move Z up a bit and retract filament even more\nG28          ;Home\t\t\t\t\t\t\t\t\t\t ;move X/Y to min endstops, so the head is out of the way\nM84          ;steppers off\nG90          ;absolute positioning\nM112        ;reset W.I.S.P.E.R.\n",
    "GCodeHeader": "G21        ;metric values\nG90        ;absolute positioning\nM82        ;set extruder to absolute mode\nM107       ;start with the layer fan off\nG28         ;Re-home\nG1 Z15.0 ;move the platform to 15mm\nG92 E0     ;zero the extruded length\nG1 F200 E3   ;extrude 3mm of feed stock\nG92 E0        ;zero the extruded length again\nG1",
    "HShellAngle": 0,
    "HShellAngleInc": 90,
    "HShellCnt": 5,
    "HShellDensity": 1,
    "HShellMinLineLen": 0.80000001192092896,
    "HShellType": 0,
    "HeadTemp": 210,
    "HeadTempEnabled": true,
    "InfillAngle": 0,
    "InfillAngleInc": 0,
    "InfillDensity": 1,
    "InfillThickness": 1,
    "InfillType": 1,
    "InitialLayerCnt": 3,
    "InitialLayerSpeed": 0.5,
    "InnerHair": true,
    "LayerHeight": 0.20000000298023224,
    "LayerStartPos": 1,
    "LoopFillOverlap": 1,
    "MinLayerTime": 10,
    "OuterHair": true,
    "PathSmoothing": 0.079999998211860657,
    "PerimeterGap": 1,
    "PolyFillerAlg": 0,
    "RaftConfig": "Type ; LayerHeight ; FillDensity ; Angle\n3       ;  0.4              ; 0.1            ; 45\n3       ;  0.4              ; 0.1            ; 0\n1       ;  0.1              ; 0.3           ; 20\n1       ;  0.1              ; 0.3           ; 90\n",
    "RaftEnable": false,
    "RaftOffset": 5,
    "RepairCorners": true,
    "RetractSpeed": 50,
    "SkirtEnable": true,
    "SkirtMinCount": 3,
    "SkirtMinLength": 100,
    "SkirtOffset": 10,
    "TravelHeight": 0,
    "TravelMinDist": 1,
    "TravelPrime": 4.5,
    "TravelRetract": 4.5,
    "TravelSpeed": 200,
    "VShellCnt": 4,
    "VShellOffset": 0,
    "VerticalSpeed": 40,
    "WipeLength": 0.5,
    "WipeSpeed": 35,
    "ZAdjust": 0
}