# generated by Slic3r 0.9.10b on Wed Sep 25 20:45:58 2013
avoid_crossing_perimeters = 1
bed_size = 270,270
bed_temperature = 60
bottom_solid_layers = 8
bridge_acceleration = 0
bridge_fan_speed = 50
bridge_flow_ratio = 1
bridge_speed = 35
brim_width = 2
complete_objects = 
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 0
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn bed off\nG90\nG92 E0\nG28 ; home \nM84 ; disable motors
external_perimeter_speed = 80%
external_perimeters_first = 
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = -12.5x0,-12.5x0
extrusion_axis = E
extrusion_multiplier = .95,.94,.94,.95
extrusion_width = .6
fan_always_on = 
fan_below_layer_time = 60
filament_diameter = 1.75,1.75,1.75,1.75
fill_angle = 45
fill_density = .1
fill_pattern = honeycomb
first_layer_bed_temperature = 60
first_layer_extrusion_width = .6
first_layer_height = 175%
first_layer_speed = 40%
first_layer_temperature = 190,235,235,226
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = .6
infill_first = 
infill_only_where_needed = 
infill_speed = 50
layer_gcode = 
layer_height = .15
max_fan_speed = 60
min_fan_speed = 55
min_print_speed = 7
min_skirt_length = 0
notes = 
nozzle_diameter = 0.5,0.5
only_retract_when_crossing_perimeters = 1
output_filename_format = [input_filename_base].gco
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = .6
perimeter_speed = 50
perimeters = 3
post_process = 
print_center = 0,0
raft_layers = 0
randomize_start = 1
resolution = 0
retract_before_travel = 2,2
retract_layer_change = 1,1
retract_length = 1.5,1.5
retract_length_toolchange = 25,15
retract_lift = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 1,1
retract_speed = 38,38
rotate = 0
scale = 1
skirt_distance = 6
skirt_height = 1
skirts = 3
slowdown_below_layer_time = 40
small_perimeter_speed = 30%
solid_fill_pattern = concentric
solid_infill_below_area = 40
solid_infill_every_layers = 0
solid_infill_extrusion_width = .6
solid_infill_speed = 30
spiral_vase = 0
start_gcode = T0\nG28 ; home all axes\nG1 Z270 F500 ; brings to a safe zone to switch T0 and T1
support_material = 
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = .6
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 70
support_material_threshold = 45
temperature = 185,235,235,226
threads = 4
toolchange_gcode = M107 ; disable fan\n;M104 S215 T[previous_extruder]  ; set temperature dont wait for temp\nM109 S225 T[next_extruder] ; wait for temperature to be meet\nM106 S115 ; turn fan on to fourty five percent
top_infill_extrusion_width = .6
top_solid_infill_speed = 50
top_solid_layers = 10
travel_speed = 130
use_relative_e_distances = 0
vibration_limit = 0
wipe = 1,1
z_offset = 0