{
    "AccelCornerCoef": 4,
    "AccelEnable": false,
    "AccelMax": 800,
    "AccelMinSpeed": 10,
    "AccelTimeStep": 20,
    "AlternatingLoopDir": false,
    "AvoidHoles": true,
    "AvoidIslands": true,
    "BedTemp": 0,
    "BedTempEnabled": true,
    "BedTempWait": true,
    "BrimCount": 3,
    "BrimEnable": false,
    "DisableCraftBotAccel": true,
    "DisplayPercentage": false,
    "DrawSpeed": 30,
    "EarlyExtrusionDelay": 80,
    "EarlyExtrusionEnable": false,
    "ExtruderSpeedMult": 1,
    "ExtrusionWidth": 0.5,
    "FanDisableOnFirstNLayer": 1,
    "FanEnable": true,
    "FanSpeedPercent": 1,
    "FilamentDiameter": 1.75,
    "FirstLayerDrawSpeed": 10,
    "FirstLayerExtruderSpeedMult": 1,
    "FirstLayerHeight": 0.20000000298023224,
    "FixWindingErrors": true,
    "GCodeFooter": "M104 S0  ;extruder heater off\nM140 S0  ;heated bed heater off (if you have it)\nM107       ;turn the layer fan off\nG91         ;relative positioning\nG1 E-1 F3000  ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-150 F6000 ;move Z up a bit and retract filament even more\nG28          ;Home\t\t\t\t\t\t\t\t\t\t ;move X/Y to min endstops, so the head is out of the way\nM84          ;steppers off\nG90          ;absolute positioning\nM112        ;reset W.I.S.P.E.R.\n",
    "GCodeHeader": "G21        ;metric values\nG90        ;absolute positioning\nM82        ;set extruder to absolute mode\nM107       ;start with the layer fan off\nG28         ;Re-home\nG1 Z15.0 ;move the platform to 15mm\nG92 E0     ;zero the extruded length\nG1 F200 E3   ;extrude 3mm of feed stock\nG92 E0        ;zero the extruded length again\nG1",
    "HShellAngle": 0,
    "HShellAngleInc": 90,
    "HShellCnt": 5,
    "HShellCntBottom": 5,
    "HShellDensity": 1,
    "HShellEnabled": true,
    "HShellMicroTravels": true,
    "HShellMinLineLen": 0.80000001192092896,
    "HShellSpeedMult": 1,
    "HShellType": 0,
    "HeadTemp": 230,
    "HeadTempEnabled": true,
    "HeadTempWait": true,
    "HeatingOrder": 0,
    "InfillAngle": 0,
    "InfillAngleInc": 60,
    "InfillDensity": 0.099999994039535522,
    "InfillEnabled": true,
    "InfillSpeedMult": 1,
    "InfillThickness": 1,
    "InfillType": 3,
    "InnerLoopWidth": 1,
    "IslandRetractHShell": false,
    "IslandRetractPerimeter": false,
    "IslandStartPos": 0,
    "LayerHeight": 0.20000000298023224,
    "LayerRange_Bottom": 0,
    "LayerRange_Top": 10000,
    "LayerScript": "",
    "LeadInLen": 1.7999999523162842,
    "LeadInOutAngle": 5,
    "LeadOutLen": 1.7999999523162842,
    "LoopInfillOverlap": 0.20000000298023224,
    "MinLayerTime": 10,
    "OrderId": 0,
    "PathSmoothing": 0.079999998211860657,
    "PerimeterGap": 0.5,
    "PerimeterSpeedMult": 0.5,
    "PerimeterWidth": 1,
    "RaftConfig": "Type;LayerHeight;FillDensity;Angle\n3;0.400000006;0.1;60\n3;0.400000006;0.1;45\n2;0.400000006;0.3;0\n",
    "RaftEnable": false,
    "RaftOffset": 5,
    "RaftOnlyUnderSupport": false,
    "RaiseFirstObjectLayer": 0.25,
    "RetractSpeed": 100,
    "SkirtEnable": true,
    "SkirtMinCount": 2,
    "SkirtMinLength": 100,
    "SkirtOffset": 10,
    "SoftSupportWidth": 0.44999998807907104,
    "StartupExtrude": 0,
    "SupportSpeedMult": 1.5,
    "SupportWidth": 0.84999996423721313,
    "TopmostShellDensity": 1,
    "TopmostShellEnabled": false,
    "TopmostShellSpeedMult": 0.59999996423721313,
    "TopmostShellType": 0,
    "TravelHeight": 1.2000000476837158,
    "TravelMinDist": 1.5,
    "TravelPrime": 5.8000001907348633,
    "TravelRetract": 5.8000001907348633,
    "TravelSpeed": 150,
    "UseG1ForTravel": true,
    "VShellCnt": 3,
    "VShellOffset": -0.070000000298023224,
    "VaseMode": false,
    "VerticalSpeed": 100,
    "WarmupFillEnabled": true,
    "WarmupFillLen": 10,
    "WeightCloseToSource": 0.30000001192092896,
    "WeightFacingTowardsSource": 1,
    "WeightNearToPreviousPoint": 0.5,
    "WeightProperCornerAngle": 3,
    "WipeLength": 0.5,
    "WipeSpeed": 40,
    "ZAdjust": 0
}