; Basic configuration for Blue MAX - a Rostock MAX v1 ; Communication and general M111 S0 ; Debug off M550 PBlueMAX ; Machine name and Netbios name (can be anything you like) M551 Prostock ; Machine password (used for FTP) M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xED ; MAC Address ;*** Adjust the IP address and gateway in the following 2 lines to suit your network M552 P10.1.10.5 ; IP address. Default is 14 but already in use so use 21 M554 P10.1.10.1 ; Gateway M553 P255.255.255.0 ; Netmask M555 P2 ; Set output to look like Marlin G21 ; Work in millimetres G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ;M575 P1 B57600 S1 ; Set auxillary serial port baud rate and require checksum (For PanelDue) ;Turn off fans ;M106 I1 ; fans are inverting M106 P0 S0 ; Turn off Fan 0 (backward compatible with older firmware) ;M106 P1 S0 ; Turn off Fan 1 M106 P1 T60 S55 ;Activate Fan #1 if the extruder temp is over 60C. ; Axis and motor configuration M569 P0 S0 ; X Drive 0 goes backwards M569 P1 S0 ; Y Drive 1 goes backwards M569 P2 S0 ; Z Drive 2 goes backwards M569 P3 S0 ; E0 Drive 3 (extruder) goes backwards M569 P4 S1 ; E1 Drive 4 goes forwards M569 P5 S1 ; E2 Drive 5 goes forwards M569 P6 S1 ; E3 Drive 6 goes forwards M569 P7 S1 ; E4 Drive 7 goes forwards ;M569 P8 S1 ; E5 Drive 8 goes forwards - not used with 2-fans version of firmware. M574 X2 Y2 Z2 S1 ; set endstop configuration (all endstops at high end, active high) ;*** The homed height is deliberately set too high in the following - you will adjust it during calibration. M665 R144 L290.8 B140 H360.0 ; set delta radius, diagonal rod length, printable radius and homed height M666 X0.00 Y0.00 Z0.00 ; put your endstop adjustments here, as given by auto calibration 22/05/15 M92 X80 Y80 Z80 ; Set axis steps/mm M906 X1000 Y1000 Z1000 E1500:1500:1500:1500:1500:1500 ; Set motor currents (mA); set each extruder explicitly M906 I100 ; Set motor idle factor to 100% while testing so they don't idle at all M201 X1000 Y1000 Z1000 E1000 ; Accelerations (mm/s^2) Set all E-motors the same M203 X20000 Y20000 Z20000 E3600 ; Maximum speeds (mm/min) Set all E-motors the same M566 X1200 Y1200 Z1200 E1200 ; Maximum instant speed changes mm/minute. Set all E-motors the same ; Thermistors ; Duet0.8.5 uses 4.7K resistors M305 P0 T100000 B3950 R4700 H30 L0 ; Put your own H and/or L values here to set the bed thermistor ADC correction M305 P1 T100000 B4267 R4700 H30 L0 ; Put your own H and/or L values here to set the 1st nozzle thermistor ADC correction M305 P2 T100000 B4267 R4700 H30 L0 ; Put your own H and/or L values here to set the 2nd nozzle thermistor ADC correction M305 P3 T100000 B4267 R4700 H30 L0 ; Put your own H and/or L values here to set the 3rd nozzle thermistor ADC correction M305 P4 T100000 B4267 R4700 H30 L0 ; Put your own H and/or L values here to set the 4th nozzle thermistor ADC correction M305 P5 T100000 B4267 R4700 H30 L0 ; Put your own H and/or L values here to set the 5th nozzle thermistor ADC correction ;M305 P6 T100000 B4267 R4700 H30 L0 ; Put your own H and/or L values here to set the 6th nozzle thermistor ADC correction M570 S180 ; Hot end may be a little slow to heat up so allow it 180 seconds ; Tool definitions FOR stock SeeMeCNC hot end - Tool 0. M563 P0 D0 H1 ; Define tool 0 G10 P0 S0 R0 ; Set tool 0 operating and standby temperatures M92 E94.35 ; Set steps/mm for extruder 0. ;*** If you have a dual-nozzle build, un-comment the next 2 lines ;M563 P1 D1 H2 ; Define tool 1 ;G10 P1 S0 R0 ; Set tool 1 operating and standby temperatures ;*** With a Duex 4 add 3 more tools ;M563 P2 D2 H3 ; Define tool 2 ;G10 P2 S0 R0 ; Set tool 0 operating and standby temperatures ;M563 P3 D3 H4 ; Define tool 3 ;G10 P3 S0 R0 ; Set tool 0 operating and standby temperatures ;M563 P4 D4 H5 ; Define tool 4 ;G10 P4 S0 R0 ; Set tool 0 operating and standby temperatures ;M563 P5 D5 H6 ; Define tool 5 ;G10 P5 S0 R0 ; Set tool 0 operating and standby temperatures // Z probe and compensation definition ;*** If you have an IR zprobe instead of a switch, change P4 to P1 in the following M558 command ;*** FSR is a switch, so set to P4! Is H3 important? M558 P4 X0 Y0 Z0 H5 F300 ; Z probe is a switch and is not used for homing any axes G31 X0 Y0 Z0 ; Set the zprobe height and threshold (put your own values here) ;*** If you are using axis compensation, put the figures in the following command M556 S78 X0 Y0 Z0 ; Axis compensation here M208 S1 Z-0.2 ; set minimum Z ; T0 ; select first hot end.