Max v2 issue with peaks and valleys in bed map[NEW DATA]

Having a problem? Post it here and someone will be along shortly to help
Mac The Knife
ULTIMATE 3D JEDDI
Posts: 1368
Joined: Sun May 11, 2014 6:18 pm

Re: Max v2 issue with peaks and valleys in bed map[NEW DATA]

Post by Mac The Knife » Mon Jul 22, 2019 7:39 am

Have you printed anything yet?
R-Max V2
Eris
Folger Tech FT-5 R2

User avatar
geneb
ULTIMATE 3D JEDDI
Posts: 4922
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Re: Max v2 issue with peaks and valleys in bed map[NEW DATA]

Post by geneb » Mon Jul 22, 2019 8:40 am

That's not going to make a difference in anything, really.

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects

clytle374
Printmaster!
Posts: 37
Joined: Wed Apr 20, 2016 1:23 am

Re: Max v2 issue with peaks and valleys in bed map[NEW DATA]

Post by clytle374 » Mon Jul 22, 2019 8:46 am

Mac The Knife wrote:
Mon Jul 22, 2019 7:39 am
Have you printed anything yet?
Yes, just have first layer issues further out near the edges of the bed
geneb wrote:
Mon Jul 22, 2019 8:40 am
That's not going to make a difference in anything, really.

g.
Has anyone tried? I've seen industrial drives eat belts that way.

I guess I'll order some new stock idlers and see if anything improves.

Thanks again
Cory

Mac The Knife
ULTIMATE 3D JEDDI
Posts: 1368
Joined: Sun May 11, 2014 6:18 pm

Re: Max v2 issue with peaks and valleys in bed map[NEW DATA]

Post by Mac The Knife » Mon Jul 22, 2019 12:12 pm

"Yes, just have first layer issues further out near the edges of the bed"
On my RMv2, I blamed that on tower rotation changes, and blamed it on humidity changes.
R-Max V2
Eris
Folger Tech FT-5 R2

clytle374
Printmaster!
Posts: 37
Joined: Wed Apr 20, 2016 1:23 am

Re: Max v2 issue with peaks and valleys in bed map[NEW DATA]

Post by clytle374 » Mon Jul 29, 2019 10:10 am

Replaced the idlers and bearings with new stock parts. Belts and pulleys with gates parts. Very slight improvement.

Printed a delta calibration part and found the dimensions to be within reason. 60mm was dead on inline with the X tower, and about .2mm short inline with the y and z towers.

As good as it's getting. I've beat this horse too long. Thanks everyone for the input.

Cory

User avatar
geneb
ULTIMATE 3D JEDDI
Posts: 4922
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Re: Max v2 issue with peaks and valleys in bed map[NEW DATA]

Post by geneb » Tue Jul 30, 2019 8:47 am

Thanks for the tip on the 8 factor calibration. It solved an issue I've had with a frankestein v3.2 I built. :)

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects

clytle374
Printmaster!
Posts: 37
Joined: Wed Apr 20, 2016 1:23 am

Re: Max v2 issue with peaks and valleys in bed map[NEW DATA]

Post by clytle374 » Thu Aug 01, 2019 10:34 am

geneb wrote:
Tue Jul 30, 2019 8:47 am
Thanks for the tip on the 8 factor calibration. It solved an issue I've had with a frankestein v3.2 I built. :)

g.
Good deal, glad someone learned something here.
Thanks for your input.
Cory

SoCalSteve
Prints-a-lot
Posts: 27
Joined: Tue Sep 30, 2014 10:26 pm

Re: Max v2 issue with peaks and valleys in bed map[NEW DATA]

Post by SoCalSteve » Tue Sep 03, 2019 5:00 pm

Have you verified that your arm length is correct in the programming?

clytle374
Printmaster!
Posts: 37
Joined: Wed Apr 20, 2016 1:23 am

Re: Max v2 issue with peaks and valleys in bed map[NEW DATA]

Post by clytle374 » Wed Sep 04, 2019 3:28 pm

SoCalSteve wrote:
Tue Sep 03, 2019 5:00 pm
Have you verified that your arm length is correct in the programming?
Many times
Thanks
Cory

Post Reply

Return to “Troubleshooting”