Eris Smart Controller

The ERIS Delta, a truly affordable entry into Delta 3D Printing
Mac The Knife
ULTIMATE 3D JEDDI
Posts: 1340
Joined: Sun May 11, 2014 6:18 pm

Eris Smart Controller

Postby Mac The Knife » Sun May 22, 2016 5:59 pm

Using the same controller as it's big brothers,
Attachments
ERIS Smart Controller.JPG
ERIS Smart Controller Back.JPG
ERIS Smart Controller.PDF
(288.63 KiB) Downloaded 29 times
ERIS Smart Controller back.PDF
(433.3 KiB) Downloaded 30 times
R-Max V2
Eris
Folger Tech FT-5 R2

Mac The Knife
ULTIMATE 3D JEDDI
Posts: 1340
Joined: Sun May 11, 2014 6:18 pm

Re: Eris Smart Controller

Postby Mac The Knife » Mon May 23, 2016 7:35 am

I checked the fit of the cover this morning before work, and it fit fine. The knob is a little large, I'll shrink that down to size to match the one on the EZ struder. Tonight I'll see how the reset button installs.
R-Max V2
Eris
Folger Tech FT-5 R2

Mac The Knife
ULTIMATE 3D JEDDI
Posts: 1340
Joined: Sun May 11, 2014 6:18 pm

Re: Eris Smart Controller

Postby Mac The Knife » Mon May 23, 2016 9:20 pm

Files are up on Thingiverse,,,,, http://www.thingiverse.com/thing:1584617
Attachments
DSC_0655.JPG
DSC_0653.JPG
R-Max V2
Eris
Folger Tech FT-5 R2

Mac The Knife
ULTIMATE 3D JEDDI
Posts: 1340
Joined: Sun May 11, 2014 6:18 pm

Re: Eris Smart Controller

Postby Mac The Knife » Mon May 23, 2016 10:27 pm

And as a side note, if you hit the reset button while printing, it does not go back to home position.
R-Max V2
Eris
Folger Tech FT-5 R2

Mac The Knife
ULTIMATE 3D JEDDI
Posts: 1340
Joined: Sun May 11, 2014 6:18 pm

Re: Eris Smart Controller

Postby Mac The Knife » Thu Jul 14, 2016 8:39 pm

If you have a display hooked up to your Eris printer, and have an itch to try the latest firmware,,,, Don't do it unless you have a copy of your current firmware. After Jetguy posted that the latest firmware doesn't enable the display, i tried it for myself last night. Not only does the display not work, neither does the sd card reader. The website's chat window din't reply to my queries,,,, and GeneB's reply on the other thread is basically "the Eris doesn't come with a display, so of course it's not enabled."

If anyone figures out the work around for this,,, post it up!!
R-Max V2
Eris
Folger Tech FT-5 R2

Jetguy
Printmaster!
Posts: 40
Joined: Mon May 23, 2016 8:23 am

Re: Eris Smart Controller

Postby Jetguy » Fri Jul 15, 2016 7:17 pm

Use my config.h from that same post. I figured out the easy way to "fix" that.

Caution, the attached config was for upgraded motors and that might overheat the stock motors or cause problems. Sorry, just was a little quick on the posting there and forgot my changes.

Again, do not use this config unless you also upgraded the XYZ motors.

The line to enable LCD is line 738, just change to type 13 and that solves it.
Attachments
Configuration.h
(27.42 KiB) Downloaded 9 times
Last edited by Jetguy on Fri Jul 15, 2016 7:42 pm, edited 1 time in total.

Mac The Knife
ULTIMATE 3D JEDDI
Posts: 1340
Joined: Sun May 11, 2014 6:18 pm

Re: Eris Smart Controller

Postby Mac The Knife » Fri Jul 15, 2016 7:21 pm

Jetguy wrote:Use my config.h from that same post. I figured out the easy way to "fix" that.

Thanks!!
R-Max V2
Eris
Folger Tech FT-5 R2

Jetguy
Printmaster!
Posts: 40
Joined: Mon May 23, 2016 8:23 am

Re: Eris Smart Controller

Postby Jetguy » Fri Jul 15, 2016 7:30 pm

Oops, caution, caution my config was for changed motors!!!! Do not use the whole config if you did not match my XYZ Eris motor upgrade.
Just change line 738 in your config.h

Again, simplest change ever. Change from type 0 to type 13 and flash.

Mac The Knife
ULTIMATE 3D JEDDI
Posts: 1340
Joined: Sun May 11, 2014 6:18 pm

Re: Eris Smart Controller

Postby Mac The Knife » Fri Jul 15, 2016 7:51 pm

Got it, Done, and Thanks!!
R-Max V2
Eris
Folger Tech FT-5 R2


Return to “ERIS Delta”

Who is online

Users browsing this forum: No registered users and 1 guest