Betacha cant print this. wide Calibration test

Post your prints with the GCode used to help other users achieve a similar result, or get help.
User avatar
mrbi11
Printmaster!
Posts: 109
Joined: Mon Nov 18, 2013 7:18 pm

Betacha cant print this. wide Calibration test

Postby mrbi11 » Sat Dec 28, 2013 7:56 pm

20131121_083530.jpg


Very simple file prints 0.5mm high by 1.5mm (3 stripes) wide at safe edge. "138mm" radius.

Calibration errors in center tend to cancel each other out. At the edge sometimes they add together.
Also printer parts out of tolerance can show up on the edge.

If it has problems, it will make bare spots, trying to print too low, or print in the air which you can tell by
it not sticking.

File sets temperatures for abs. If you need to change it, u no how.
Attachments
cir138VE.gco
(5.95 KiB) Downloaded 151 times

User avatar
Eaglezsoar
ULTIMATE 3D JEDDI
Posts: 7185
Joined: Sun Apr 01, 2012 5:26 pm

Re: Betacha cant print this. wide Calibration test

Postby Eaglezsoar » Sun Dec 29, 2013 1:55 am

Thanks for the file. You are probably correct in that most printers will not be able to print it without problems.
“ Do Not Regret Growing Older. It is a Privilege Denied to Many. ”

User avatar
bubbasnow
ULTIMATE 3D JEDDI
Posts: 1064
Joined: Fri Aug 02, 2013 4:24 pm
Location: Dayton, WA

Re: Betacha cant print this. wide Calibration test

Postby bubbasnow » Sun Dec 29, 2013 2:13 am

so how did you do this without the metal build plate?

HumanLiberty
Printmaster!
Posts: 75
Joined: Tue Apr 14, 2015 4:27 pm

Re: Betacha cant print this. wide Calibration test

Postby HumanLiberty » Sun Jul 26, 2015 8:23 pm

276mm ≠ 280mm

I can do a 276 circle too, but so far cannot really meaningfully print that far out.
I have elevated the bed on 2" spacers to allow the Cheapskate to move down past it further, thus bringing the delta arms closer to horizontal, thus extending their reach. So far the results are promising, but calibration seems to be a bitch - I'll be trying Rollie's method if I can: viewtopic.php?f=36&t=8698&start=25

We'll see what happens...

User avatar
KAS
ULTIMATE 3D JEDDI
Posts: 1157
Joined: Thu Dec 04, 2014 6:06 pm

Re: Betacha cant print this. wide Calibration test

Postby KAS » Sun Jul 26, 2015 8:52 pm

I run with the hotend under the effector, pretty much does the same thing.

User avatar
mrbi11
Printmaster!
Posts: 109
Joined: Mon Nov 18, 2013 7:18 pm

Re: Betacha cant print this. wide Calibration test

Postby mrbi11 » Mon Jul 27, 2015 5:59 pm

There is an essential problem with tiny variations in arm lengths, connectors, which is almost unavoidable with sanding the parts to fit.
The geometry of two parallel arms is intuitively great, and variations tend to get averaged out in the center of the printer.
However, the "worst" places the small variations, say 0.1mm, which are generally ignorable, get multiplied
when the arms are moved to the side at maximum deflection. There is an area where the errors get multiplied vertically,
so even well matched arms may get a vertical error of up to 0.5mm, again not disastrous except on the very first layer.
If you can print this, you have an exceptionally well made machine, congratulations!


Return to “GCode & Test Prints”

Who is online

Users browsing this forum: No registered users and 1 guest