.AMF Files

Talk about the Repetier Host software here (http://repetier.com)
Robaire
Plasticator
Posts: 14
Joined: Mon Aug 10, 2015 2:50 pm

.AMF Files

Postby Robaire » Sat Aug 22, 2015 1:18 am

Now that SolidWorks has added more support for 3D printers and saving to an .AMF file I've been trying to get Repetier to load the file. However it never loads the model properly, always extremely small. You can barely see it on the print bed. Does anyone have any advice or know how to get AMF files loading properly.

User avatar
0110-m-p
Printmaster!
Posts: 456
Joined: Sun Oct 20, 2013 9:23 am
Location: Atlanta, GA

Re: .AMF Files

Postby 0110-m-p » Sat Aug 22, 2015 9:40 am

I'm not familiar with Solidworks/.AMF specifically, but it sounds like it is being exported with different units than Repetier-Hose is trying to import them. Usually units should be in millimeters before importing to 3D printer software. If Solidworks properties has the model in meters, then it will be 1000 times smaller when imported to Repetier-Host.
Current Machines || Rostock Max (V1) | V3DR ||
Previous Machines || Flashforge Creator Pro ||

Robaire
Plasticator
Posts: 14
Joined: Mon Aug 10, 2015 2:50 pm

Re: .AMF Files

Postby Robaire » Sun Aug 23, 2015 12:16 am

Ah thanks. I'll look into it, I normally use SolidWorks with imperial units as I am American.

User avatar
geneb
ULTIMATE 3D JEDDI
Posts: 4357
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Re: .AMF Files

Postby geneb » Sun Aug 23, 2015 9:46 am

You might be American (most of us are), but 1) 99.9% of the rest of the world uses metric and 2) 100% of the 3d printers out there (with possible exceptions in Stratasys and 3D Systems lines) use metric natively. As far as I know, ALL the slicing packages out there only grok metric. You'll be better off in the long run if you change your UoM to millimeters in SolidWorks. :)

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects

User avatar
Jimustanguitar
ULTIMATE 3D JEDDI
Posts: 2617
Joined: Sun Mar 31, 2013 1:35 am
Location: Notre Dame area
Contact:

Re: .AMF Files

Postby Jimustanguitar » Sun Aug 23, 2015 8:04 pm

Image

IMBoring25
Printmaster!
Posts: 598
Joined: Wed Mar 18, 2015 1:11 am

Re: .AMF Files

Postby IMBoring25 » Sun Aug 23, 2015 8:28 pm

To be fair, none of that information tells you how much energy it takes to boil a metric unit of water either. It only tells you how much energy it takes to bring it to the boiling point. Enthalpy of vaporization is a different matter.

Mac The Knife
ULTIMATE 3D JEDDI
Posts: 1293
Joined: Sun May 11, 2014 6:18 pm

Re: .AMF Files

Postby Mac The Knife » Sun Aug 23, 2015 9:06 pm

It's all French to me.
R-Max V2
Eris


Return to “Repetier Host”

Who is online

Users browsing this forum: No registered users and 1 guest