Anyone have upgrade instructions from H1 to H1.1?

All about the retired H-1.1 3D Printers
jcugnoni
Plasticator
Posts: 18
Joined: Sat May 19, 2012 5:11 am

Re: Anyone have upgrade instructions from H1 to H1.1?

Postby jcugnoni » Tue Jul 31, 2012 12:42 pm

Hi

Until the official guide is done, here are some pictures of my interpretation of the guiding block assemblies. I hope it will help those who are stuck with all those screws ;)

All guides pre-assembled:
top left = X axis, top right = Z axis and bottom Y axis
20120731_025.jpg


Detail of the Y axis bearing block:
20120731_021.jpg


Detail of Y axis linear guide block:
20120731_017.jpg


Detail of X axis guiding blocks:
20120731_010.jpg


How to insert the bearings in X axis blocks:
20120731_011.jpg

20120731_013.jpg

User avatar
AndGorew
Prints-a-lot
Posts: 30
Joined: Mon Mar 26, 2012 11:36 pm
Location: Springfield, Illinois

Re: Anyone have upgrade instructions from H1 to H1.1?

Postby AndGorew » Tue Jul 31, 2012 12:55 pm

thanks! that helps a bunch! i have already started to assemble the main frame using the old instructions as a guide (just so i know how it all goes together just in case i am using the wrong parts ;) ) and have already got to the point where my print board is moving along very smooth-like :) its verry exciting!

johnoly99
Printmaster!
Posts: 736
Joined: Mon Mar 26, 2012 1:07 pm
Location: Goshen, IN
Contact:

Re: Anyone have upgrade instructions from H1 to H1.1?

Postby johnoly99 » Tue Jul 31, 2012 1:08 pm

Alright! It's like an erector set isn't it? Those all look perfect from what I can see!
SeeMeCNC Co-Founder & V.P.

User avatar
AndGorew
Prints-a-lot
Posts: 30
Joined: Mon Mar 26, 2012 11:36 pm
Location: Springfield, Illinois

Re: Anyone have upgrade instructions from H1 to H1.1?

Postby AndGorew » Tue Jul 31, 2012 2:59 pm

Haha im not old enough to remember those. i have only heard about them and i know what they look like but ive never actually played with those. Does this look right to you? The black bar connectors are lose but the blue one are tight. I have been using these sheetmetal screws to go in the bar connectors. I hope thats what they were intended for :) its not a big deal if i mess up now because i am going to go through every step on the instructions when they are posted to make sure i did everything correctly.
Attachments
photo7.JPG
photo6.JPG

jasco13
Printmaster!
Posts: 67
Joined: Sun Jul 08, 2012 6:53 pm

Re: Anyone have upgrade instructions from H1 to H1.1?

Postby jasco13 » Tue Jul 31, 2012 3:01 pm

johnoly99 wrote:Yep, we've checked all the kits that went out since last thursday, and some did go out without the few parts mentioned. Just email us what it is you're missing


Could you please publish the parts list so that we can go through and check the parts we received. It is hard to know what is missing until we have an official parts list. I have a lot of stuff missing compared to the H1 parts list, but I'm operating under the assumption that the two parts lists are not the same.

Thanks,

matt

User avatar
AndGorew
Prints-a-lot
Posts: 30
Joined: Mon Mar 26, 2012 11:36 pm
Location: Springfield, Illinois

Re: Anyone have upgrade instructions from H1 to H1.1?

Postby AndGorew » Tue Jul 31, 2012 3:05 pm

They are deffinitely not the same. With that can you also post you email address. WHich ever one you want us to contact you at.

johnoly99
Printmaster!
Posts: 736
Joined: Mon Mar 26, 2012 1:07 pm
Location: Goshen, IN
Contact:

Re: Anyone have upgrade instructions from H1 to H1.1?

Postby johnoly99 » Tue Jul 31, 2012 3:08 pm

Will do. Steve's going thru it to triple check it. seemecnc @ gmail is the address
SeeMeCNC Co-Founder & V.P.

jasco13
Printmaster!
Posts: 67
Joined: Sun Jul 08, 2012 6:53 pm

Re: Anyone have upgrade instructions from H1 to H1.1?

Postby jasco13 » Thu Aug 02, 2012 12:40 pm

What is the word on the parts list?

User avatar
AndGorew
Prints-a-lot
Posts: 30
Joined: Mon Mar 26, 2012 11:36 pm
Location: Springfield, Illinois

Re: Anyone have upgrade instructions from H1 to H1.1?

Postby AndGorew » Thu Aug 02, 2012 8:16 pm

I haven't heard anything yet :/

jasco13
Printmaster!
Posts: 67
Joined: Sun Jul 08, 2012 6:53 pm

Re: Anyone have upgrade instructions from H1 to H1.1?

Postby jasco13 » Thu Aug 02, 2012 8:39 pm

Seems like there should be a parts list somewhere. They shipped the kits so they had to know what to put in them. I just want the parts list so that I can request any missing pieces and hopefully get them before the build instructions are published. I would like to begin building as soon as we get the instructions. I think it would have been better to wait on sending out the kits until the instructions where completed.

User avatar
AndGorew
Prints-a-lot
Posts: 30
Joined: Mon Mar 26, 2012 11:36 pm
Location: Springfield, Illinois

Re: Anyone have upgrade instructions from H1 to H1.1?

Postby AndGorew » Thu Aug 02, 2012 9:44 pm

Supposibly all of the kits are missing the same parts. I have been emailing back and forth with John and he has confirmed that they are all missing the same parts. He also said a couple days ago that the missing parts would be shipping out sometime this week so Im just gonna sit back and see if they get here or not. It's far as the parts list/instructions go I have no idea when they will be out. Hopefully soon . :)

User avatar
AndGorew
Prints-a-lot
Posts: 30
Joined: Mon Mar 26, 2012 11:36 pm
Location: Springfield, Illinois

Re: Anyone have upgrade instructions from H1 to H1.1?

Postby AndGorew » Fri Aug 03, 2012 11:46 pm


IdolCrasher
Noob
Posts: 1
Joined: Tue Oct 02, 2012 7:43 pm

Re: Anyone have upgrade instructions from H1 to H1.1?

Postby IdolCrasher » Tue Oct 02, 2012 7:49 pm

Good day all,

Are there official SeeMeCNC build manuals or videos for the H1.1 yet?

I already found the rapid fire build video uploaded by a kind user.

I am looking for the real deal now; I am attempting to upgrade an H-1 into a H-1.1


Return to “H-1.1 3D Printers”

Who is online

Users browsing this forum: No registered users and 1 guest