Search found 4685 matches

by geneb
Wed Jun 13, 2018 9:22 am
Forum: Troubleshooting
Topic: Filament Feeding Problem
Replies: 5
Views: 349

Re: Filament Feeding Problem

Possible causes are printing too fast for the extruder temp, extruder temp too cold, jammed hot end. Google "cold pull pla" for instructions on how to clear typical filament jams.

g.
by geneb
Mon Jun 11, 2018 9:04 am
Forum: Rostock MAX v3.2
Topic: Building the Whip for V3.2
Replies: 2
Views: 291

Re: Building the Whip for V3.2

The whip didn't come pre-assembled?

g.
by geneb
Fri Jun 08, 2018 7:37 am
Forum: Troubleshooting
Topic: can not connect to printer
Replies: 4
Views: 284

Re: can not connect to printer

I would suggest that you wipe the SD card and copy the data you downloaded from the git repository again.

This is something you should have already tried.

g.
by geneb
Thu Jun 07, 2018 10:20 am
Forum: Troubleshooting
Topic: Filiment stuck at hotend
Replies: 6
Views: 280

Re: Filiment stuck at hotend

It's also possible that the hot end is blocked by foreign debris - I've seen instances where metal particles, tiny ball bearings, etc. have been found in some of the cheaper filament brands.

g.
by geneb
Wed Jun 06, 2018 12:13 pm
Forum: Rostock MAX v2
Topic: Replacement Carriages
Replies: 5
Views: 560

Re: Replacement Carriages

The dampers are going to be moving just a little bit and that's what is causing the ghosting. If you've got a DuetWifi, you don't need them as the Trinamic stepper drivers on the DuetWifi are incredibly quiet. They even quieted down my v1 and the case on that thing is damn near a bongo drum. :)

g.
by geneb
Wed Jun 06, 2018 12:11 pm
Forum: Troubleshooting
Topic: Filiment stuck at hotend
Replies: 6
Views: 280

Re: Filiment stuck at hotend

Make sure that the bed clips are holding down the bed firmly. I tighten them with a screwdriver a little bit after I've moved the lever over the glass. This will help with the z probe retries. You also need to make sure that you've got the latest macro files from the git repo - the bed MUST be turne...
by geneb
Tue Jun 05, 2018 8:38 am
Forum: Artemis
Topic: Lubricating linear rails?
Replies: 12
Views: 1241

Re: Lubricating linear rails?

Did you tell him about the rubbing issue?

g.
by geneb
Fri Jun 01, 2018 8:05 am
Forum: Troubleshooting
Topic: ERIS - Clicking Sound, No Filament Coming Out, Unload Doesn't Work :(
Replies: 8
Views: 431

Re: ERIS - Clicking Sound, No Filament Coming Out, Unload Doesn't Work :(

What happens when you hand-feed filament through the system?

g.
by geneb
Thu May 31, 2018 9:27 am
Forum: Troubleshooting
Topic: ERIS - Clicking Sound, No Filament Coming Out, Unload Doesn't Work :(
Replies: 8
Views: 431

Re: ERIS - Clicking Sound, No Filament Coming Out, Unload Doesn't Work :(

The clicking sound is called "skipping". It's what the extruder does when it can't feed filament.

Is the hot end set to the correct temperature for the filament you're using?

g.
by geneb
Thu May 31, 2018 9:22 am
Forum: Rostock MAX v3
Topic: Display with white squares
Replies: 2
Views: 623

Re: Display with white squares

It's possible that the display has simply failed.

g.
by geneb
Fri May 25, 2018 7:55 am
Forum: Troubleshooting
Topic: ERIS - Clicking Sound, No Filament Coming Out, Unload Doesn't Work :(
Replies: 8
Views: 431

Re: ERIS - Clicking Sound, No Filament Coming Out, Unload Doesn't Work :(

The extruder is making a clicking noise because the hot end is jammed. The most common cause of jams that I've seen is improper retract settings or too low a temperature. The extruder has likely carved a groove in the filament, thus can't pull it out. Heat up the hot end to around 220C and pull the ...
by geneb
Mon May 21, 2018 8:38 am
Forum: The Build Zone
Topic: Red Sand's Max V2 Build Thread
Replies: 49
Views: 7590

Re: Red Sand's Max V2 Build Thread

Yep, that's the beastie. :)

g.
by geneb
Sun May 20, 2018 10:18 am
Forum: Rostock MAX v3
Topic: What happened to the pre 4/11/2017 max v3 assembly guide
Replies: 1
Views: 247

Re: What happened to the pre 4/11/2017 max v3 assembly guide

The guide is functionally identical, just re-ordered a bit. :)

g.
by geneb
Sun May 20, 2018 10:16 am
Forum: The Build Zone
Topic: Red Sand's Max V2 Build Thread
Replies: 49
Views: 7590

Re: Red Sand's Max V2 Build Thread

Another modification I recommend is the 29A power supply kit - it's a big improvement over the ATX supply.

Good luck!

g.
by geneb
Fri May 18, 2018 7:49 am
Forum: Rostock MAX v3.2
Topic: Upgraded max v3 to 3.2 question on command
Replies: 6
Views: 494

Re: Upgraded max v3 to 3.2 question on command

That problem is caused by the first probe script not turning the bed off. The new version on github shouldn't have that problem. The reason it's a big deal is that the bed throws off a lot of EMI at close range and it makes the little microcontroller on the SE300 board go nuts. If you pay close atte...
by geneb
Thu May 17, 2018 9:00 am
Forum: Rostock MAX v3.2
Topic: Upgraded max v3 to 3.2 question on command
Replies: 6
Views: 494

Re: Upgraded max v3 to 3.2 question on command

FYI, M270 was pretty short lived and isn't in the production firmware any longer.
I would grab the latest firmware & configuration files from the SeeMeCNC git repo, here: https://github.com/seemecnc/RostockMaxV3.2

g.
by geneb
Wed May 16, 2018 9:26 am
Forum: Rostock MAX v2
Topic: Newer Arduino versions that work?
Replies: 7
Views: 702

Re: Newer Arduino versions that work?

Due to resource constraints, 1.6.0 is really the only choice. Newer versions of the compiler do things differently enough that it causes random crashes in the firmware.

g.
by geneb
Wed May 16, 2018 9:25 am
Forum: Rostock MAX v3.2
Topic: Upgraded max v3 to 3.2 question on command
Replies: 6
Views: 494

Re: Upgraded max v3 to 3.2 question on command

It controls the double-tapping behavior.

g.
by geneb
Tue May 15, 2018 8:26 am
Forum: Rostock MAX v2
Topic: Newer Arduino versions that work?
Replies: 7
Views: 702

Re: Newer Arduino versions that work?

What operating system are you using?

g.
by geneb
Fri May 11, 2018 8:17 am
Forum: The Build Zone
Topic: Converting MAX v3 to ATX PSU
Replies: 6
Views: 760

Re: Converting MAX v3 to ATX PSU

The V3 isn't designed to use an ATX power supply - it simply won't fit. You'd be better off getting a Noctua (or similar) fan to replace the fan in the 29A power supply the v3 has.

g.
by geneb
Thu May 03, 2018 9:08 am
Forum: Development Topics
Topic: Artemis Browser Interface
Replies: 5
Views: 2165

Re: Artemis Browser Interface

FYI, you don't need to use SeeMeCNC's branch of RRF - you can run the "main line" branch of RRF on your Artemis (or Rostock MAX v3.2). The only changes that Ryan made to RRF have already been added to the main line branch. (As far as I know)

g.
by geneb
Sat Apr 28, 2018 9:43 am
Forum: Rostock MAX v2
Topic: Hot end won't turn off
Replies: 15
Views: 1125

Re: Hot end won't turn off

Two cartridge heaters on that hot end is murderous overkill. Just sayin'. :)

g.
by geneb
Fri Apr 27, 2018 7:35 am
Forum: Troubleshooting
Topic: Quick Clip connector
Replies: 2
Views: 216

Re: Quick Clip connector

A bit of masking tape would work too. :)

g.
by geneb
Thu Apr 26, 2018 4:55 pm
Forum: Artemis
Topic: adarcher's build/troubleshooting
Replies: 87
Views: 5561

Re: adarcher's build/troubleshooting

Cura's just doing what its told. Try changing the infill density.

g.
by geneb
Thu Apr 26, 2018 8:46 am
Forum: Artemis
Topic: adarcher's build/troubleshooting
Replies: 87
Views: 5561

Re: adarcher's build/troubleshooting

It's actually not the default rate, but the max rate. Again, to get around something dumb that Cura does.

g.

Go to advanced search