Search found 10 matches

by Mike&Mr.Stevens
Wed Jun 05, 2013 6:32 pm
Forum: H-1.1 3D Printers
Topic: Assistance Needed
Replies: 9
Views: 3118

Re: Assistance Needed

Just tweaked the settings in repetiers eeprom configuration window. works fine now.
by Mike&Mr.Stevens
Thu May 30, 2013 7:27 pm
Forum: H-1.1 3D Printers
Topic: Assistance Needed
Replies: 9
Views: 3118

Re: Assistance Needed

Cool, I'll give it a go.
by Mike&Mr.Stevens
Thu May 30, 2013 4:27 pm
Forum: H-1 3D Printers
Topic: They put me in the news paper!
Replies: 1
Views: 1459

They put me in the news paper!

They put me in the local news! Couldn't have got here without you guys!
DSC00354.JPG
DSC00353.JPG
DSC00352.JPG
by Mike&Mr.Stevens
Tue May 28, 2013 8:20 pm
Forum: H-1.1 3D Printers
Topic: Assistance Needed
Replies: 9
Views: 3118

Re: Assistance Needed

Thanks,
I'm using rambo and Marlin.
by Mike&Mr.Stevens
Tue May 28, 2013 4:16 pm
Forum: H-1.1 3D Printers
Topic: Assistance Needed
Replies: 9
Views: 3118

Re: Assistance Needed

Thanks, I think I understand but when I go into the coding and adjust the steps per mm in the z axis, the machine does not register the changes.
by Mike&Mr.Stevens
Sat May 25, 2013 5:06 pm
Forum: Troubleshooting
Topic: Tops of my prints get ruined
Replies: 11
Views: 2095

Re: Tops of my prints get ruined

I use ABS. Me and PLA don't get along.
by Mike&Mr.Stevens
Fri May 24, 2013 3:39 pm
Forum: Troubleshooting
Topic: Tops of my prints get ruined
Replies: 11
Views: 2095

Re: Tops of my prints get ruined

Looks too hot IMHO, I would slow the printer down to 50% when it gets about 3/4 up the head. I agree that it's too hot. I always thought slowing the print speed down would increase heat buildup, though. Am I wrong? In my experience allowing the lower layers to cool a bit before I lay more down seem...
by Mike&Mr.Stevens
Fri May 24, 2013 3:31 pm
Forum: H-1.1 3D Printers
Topic: Assistance Needed
Replies: 9
Views: 3118

Re: Assistance Needed

foshon wrote:I do believe your z-axis steps per/mm are 19.1% low. Have you verified that the call for 20mm gets you 20mm in lift?

I don't have the best accuracy, but here are my numbers;
Command|Result
0.1= 0.0127
0.5= 0.3556
1= 0.762
10= 8.001
20= 15.951
by Mike&Mr.Stevens
Thu May 23, 2013 4:29 pm
Forum: Troubleshooting
Topic: Tops of my prints get ruined
Replies: 11
Views: 2095

Tops of my prints get ruined

Sometimes the tops of my prints get ruined. I am running a H 1.1 on repetier with marlin firmware. 0.2 layer height. Any tips on how to fix this?
DSC00342.JPG
DSC00333.JPG
by Mike&Mr.Stevens
Fri May 17, 2013 5:17 pm
Forum: H-1.1 3D Printers
Topic: Assistance Needed
Replies: 9
Views: 3118

Assistance Needed

Hello world! I have problem with my H1.1, with no further introduction lets get to it. My Printer is fantastic with the only problem being that all of my prints turn out about 20% shorter than they should be. I have included photos of what should a 20x20x10 box. Sometimes I can compensate before I p...

Go to advanced search