Search found 148 matches

by joecnc2006
Wed Oct 22, 2014 4:00 pm
Forum: Mods and Upgrades
Topic: 3rd magnetic arm upgrade
Replies: 24
Views: 5212

Re: 3rd magnetic arm upgrade

Thread the Aluminum, screw on the ends to the exact length, then setscrew or clamp in place.
by joecnc2006
Fri May 09, 2014 9:58 am
Forum: General Tips 'N Tricks
Topic: Window Tint Print Surface on the cheap!
Replies: 22
Views: 4406

Re: Window Tint Print Surface on the cheap!

I use a coat of glue stick then a light spray of hairspray on it, you can not pull it free without a hammer, until it cools down then it just pops off.
by joecnc2006
Wed May 07, 2014 11:03 am
Forum: Design Help
Topic: Cost of Print
Replies: 16
Views: 5723

Re: Cost of Print

jesse wrote:Here's a tool I made for 3d print pricing: http://jbcse.com/3d-print-cost-estimator.php


I keep getting "an error occurred" with the tool.

Capture.JPG
by joecnc2006
Tue May 06, 2014 9:13 pm
Forum: Design Help
Topic: Cost of Print
Replies: 16
Views: 5723

Cost of Print

I have a Print I am doing it is about 3"x3"x1.5" envelope. Cura says 12.23m at 34 grams, I wanted to know what to charge for a piece like this and how others charge. I have seem on some sites $1.50 cm/3 and don't know how to equate it. Also I have seen setup fees. Any incite and advic...
by joecnc2006
Mon Apr 28, 2014 5:34 pm
Forum: The Lounge
Topic: A John Oly caption that photo contest :)
Replies: 37
Views: 4451

Re: A John Oly caption that photo contest :)

"Don't get screwed, Buy a Rostock Max V2"
by joecnc2006
Mon Apr 28, 2014 3:42 pm
Forum: Rostock MAX
Topic: Joe's Rostock Max
Replies: 40
Views: 6062

Re: Joe's Rostock Max

Owl Print

IMAG0570.jpg
by joecnc2006
Sun Apr 27, 2014 7:22 pm
Forum: Mods and Upgrades
Topic: An easy magnetic ball solution.
Replies: 74
Views: 9758

Re: An easy magnetic ball solution.

The originals have the ball end down.
by joecnc2006
Sat Apr 26, 2014 10:30 pm
Forum: GCode & Test Prints
Topic: Anyone had their Rostock or Orion play music with steppers?
Replies: 16
Views: 5866

Re: Anyone had their Rostock or Orion play music with steppe

Here is the Mario Song. The problem with this and the other music on the cnc's is the machine uses a cortisian coordinate system to make the motor moves/sounds a Delta Printer has to only use the Z-Move to make the music. m the youtube embeding is not working right, it worked just fine on my phpbb f...
by joecnc2006
Sat Apr 26, 2014 1:27 pm
Forum: Rostock MAX
Topic: Joe's Rostock Max
Replies: 40
Views: 6062

Re: Joe's Rostock Max

Printed a set of my 4 thumb screws for hold down clamps on the cnc machine.

IMAG0566.jpg
by joecnc2006
Sat Apr 26, 2014 1:22 pm
Forum: ORION
Topic: Printing large print.
Replies: 4
Views: 1021

Re: Printing large print.

I would make the body separate them make the pipes slide on similar to pvc piping, and make the middle support overlap and bolt together to hold into place.
by joecnc2006
Thu Apr 24, 2014 9:34 am
Forum: GCode & Test Prints
Topic: Anyone had their Rostock or Orion play music with steppers?
Replies: 16
Views: 5866

Re: Anyone had their Rostock or Orion play music with steppe

I would imagine if you have dampers installed it may not sound as good, but will try it out. I just have not had time yet.
by joecnc2006
Wed Apr 23, 2014 2:32 pm
Forum: KISSlicer
Topic: Soooo. Finally tried Kisslicer
Replies: 20
Views: 4976

Re: Soooo. Finally tried Kisslicer

How does Kisslicer compare to Cura?
by joecnc2006
Wed Apr 23, 2014 2:31 pm
Forum: General Tips 'N Tricks
Topic: blue tape and Z calibration
Replies: 4
Views: 832

Re: blue tape and Z calibration

I found it to be about 0.1mm I change the z-height.
by joecnc2006
Wed Apr 23, 2014 2:29 pm
Forum: GCode & Test Prints
Topic: Anyone had their Rostock or Orion play music with steppers?
Replies: 16
Views: 5866

Re: Anyone had their Rostock or Orion play music with steppe

I did it on my CNC Machines, but not on the Rostock yet, I will see if I can get one going. I have a video somewhere of my 4x4 playing some.
by joecnc2006
Thu Apr 17, 2014 7:06 pm
Forum: What are YOU making?
Topic: Check this out...
Replies: 13
Views: 1682

Re: Check this out...

Will be interested in what your setting are to pron it, Cura will not even generate g-code I imagine the walls are to close together, may have to size it up.
by joecnc2006
Thu Apr 17, 2014 5:20 pm
Forum: Troubleshooting
Topic: Printer frozen solid
Replies: 10
Views: 1417

Re: Printer frozen solid

did you try to move the cheapskates with power off? I would imagine so. If power was on the motors are energized.
by joecnc2006
Thu Apr 17, 2014 12:00 pm
Forum: Simplify3D
Topic: S3D Version 2.1.0 Released
Replies: 4
Views: 2277

Re: S3D Version 2.1.0 Released

I'm still debating if the cost is worth it, currently I use Cura and Repetier-host
by joecnc2006
Thu Apr 17, 2014 10:29 am
Forum: Troubleshooting
Topic: Frustrating calibration issues
Replies: 14
Views: 2461

Re: Frustrating calibration issues

yes the lights do flash with ardiuno software, I was thinking about the eeprom config in repetier-host.
by joecnc2006
Thu Apr 17, 2014 10:20 am
Forum: Troubleshooting
Topic: Frustrating calibration issues
Replies: 14
Views: 2461

Re: Frustrating calibration issues

I wonder when you make the changes to the eeprom if the read/write light flashes on the Rambo Board? If so this could be a way to ensure it is working properly.
by joecnc2006
Wed Apr 16, 2014 11:11 pm
Forum: The Lounge
Topic: Help Designing a part for my vending machine
Replies: 10
Views: 1535

Re: Help Designing a part for my vending machine

This Should be very close and work for you.

Capture.JPG


http://www.thingiverse.com/thing:301507
by joecnc2006
Wed Apr 16, 2014 8:26 am
Forum: The Lounge
Topic: Help Designing a part for my vending machine
Replies: 10
Views: 1535

Re: Help Designing a part for my vending machine

post pictures here?
by joecnc2006
Mon Apr 14, 2014 9:43 pm
Forum: New Member introduction
Topic: Hello from Toronto, Canada
Replies: 14
Views: 2061

Re: Hello from Toronto, Canada

for the gaps try reducing your nozzle width.
by joecnc2006
Mon Apr 14, 2014 4:07 pm
Forum: Rostock MAX
Topic: E3D V4 All metal hotend
Replies: 875
Views: 156986

Re: E3D V4 All metal hotend

where do you get the tiny bits?
by joecnc2006
Mon Apr 14, 2014 4:05 pm
Forum: Troubleshooting
Topic: Generated g-code not found
Replies: 2
Views: 486

Re: Generated g-code not found

I get the error more and more now, So I switched to CURA for g-code generation and only user repetier-Host for machine control.
by joecnc2006
Fri Apr 11, 2014 9:04 pm
Forum: Troubleshooting
Topic: Walls of printed layer fan too thick?
Replies: 8
Views: 1951

Re: Walls of printed layer fan too thick?

If you were to enclose the bottom 1/2 the way to the end It will work better, I added tape to mine and it forced the air better towards the nozzle.

Go to advanced search