Search found 36 matches

by nurbie
Sat Jul 27, 2019 8:48 pm
Forum: KISSlicer
Topic: V4 / Duet2 / KISSlicer / DUAL EXTRUSION Y-bowden FEED and RETRACT?
Replies: 2
Views: 834

Re: V4 / Duet2 / KISSlicer / DUAL EXTRUSION Y-bowden FEED and RETRACT?

well, this doesn't work: KISSLICER DUAL CONFIG TEST_01 PREFIX ; [mm] mode G21 ; absolute mode G90 ; Home G28 ; Heated bed control M140 S<BED> ; Absolute E M82 M203 Z24000 G28 ;HOME G1 Z15.0 F6000 ;MOVE PLATFORM DOWN 15MM ;PRIME EXTRUDER G92 E0 PREHEAT ; heat the (next, then current) extruder without...
by nurbie
Sat Jul 27, 2019 8:44 pm
Forum: Rostock MAX v4
Topic: Dual extrusion using KISSlicer
Replies: 3
Views: 179

Re: Dual extrusion using KISSlicer

Wow. We _ really _ need a dev chat with Jonathan @KISSlicer to integrate a SMCNC Rostock Max/other preset group. This process is a wild search with help from the KISS community being very slim. Andy/Tim, can you guys contact Jonathan and see if you can get presets going for his next rev. v2? It's cu...
by nurbie
Fri Jul 26, 2019 5:55 pm
Forum: Rostock MAX v4
Topic: Dual extrusion using KISSlicer
Replies: 3
Views: 179

Re: Dual extrusion using KISSlicer

please refer to the KISSlicer section:
V4 / Duet2 / KISSlicer / DUAL EXTRUSION Y-bowden FEED and RETRACT?
viewtopic.php?f=15&t=12782

Where I hope to find 42
by nurbie
Fri Jul 26, 2019 5:23 pm
Forum: KISSlicer
Topic: V4 / Duet2 / KISSlicer / DUAL EXTRUSION Y-bowden FEED and RETRACT?
Replies: 2
Views: 834

V4 / Duet2 / KISSlicer / DUAL EXTRUSION Y-bowden FEED and RETRACT?

V4 set-up as above KISSlicer Premium v1.6.3 I have dual enabled in the Duet config Bear with me here, I've had multi-extruder KISS for one day, and this is my first dual extrude. How the heck do you get the filament to feed and retract? I just don't know where to start with the whole retraction/feed...
by nurbie
Thu Jul 25, 2019 8:24 pm
Forum: Rostock MAX v4
Topic: Dual extrusion using KISSlicer
Replies: 3
Views: 179

Dual extrusion using KISSlicer

RMaxV4 Duet2 WiFi, standard E0 & E1 extruder stepper setup Is there anything I need to setup in the Duet config/other to let the system know how much to retract/feed as it swaps from one Bowden feed to the other? I haven't received my PRO(dual enabled) license from KISS yet, so I'm a bit ahead of te...
by nurbie
Wed May 29, 2019 2:28 am
Forum: Rostock MAX v4
Topic: Base fan upgrade for quietness
Replies: 4
Views: 742

Re: Base fan upgrade for quietness

WINNER! Just replaced the base fans in two V3s with same, Noctua NF A6x25 fans. Used the 4-pin adaptor; took connector apart to maximize wire length. Be gentle. NOW, Noticeable buzzing noise (from my CPU mini-fan / SO annoying) ... because, the base fan is now SO quiet! Noctua is moving lots of air....
by nurbie
Tue May 28, 2019 12:58 am
Forum: Rostock MAX v3
Topic: V3 conversion to WASP LDM Clay extruder process
Replies: 11
Views: 1367

Re: V3 conversion to WASP LDM Clay extruder process

JohnSL board wasn't talking to Duet because of 3.3v and +/- (two outer wires on 3pos trinket connector from kit) going to the wrong pins on the Duet. Once this was corrected the FSRs talked to the Duet perfectly . The old SE280 accelerometer calibration, which was a huge leap a couple years ago, is ...
by nurbie
Wed May 22, 2019 1:40 am
Forum: Rostock MAX v3
Topic: FSR connection to DUET 2 WiFi no workie - config?
Replies: 4
Views: 537

Re: FSR connection to DUET 2 WiFi no workie - config?

Annnnnnnd,
SOLVED
IMG_20190521_230244~2.jpg
Blue wire is not connected to anything


Wow, the FSRs are amazingly sensitive in auto calibration.
and,
I still can't figure out why the stepper movements are so quiet with the Duet; it's weird(in a good way)
by nurbie
Wed May 22, 2019 12:22 am
Forum: Rostock MAX v3
Topic: V3 conversion to WASP LDM Clay extruder process
Replies: 11
Views: 1367

Re: V3 conversion to WASP LDM Clay extruder process

Everything is working except for the FSR to Duet recognition. No matter what I try the Duet just doesn't recognize signals from the JohnSL. Sensitivity for the FSRs is awesome, triggers with a light finger touch on the deck, but Duet is just dumb to it. I'll post again once we get this figured out, ...
by nurbie
Tue May 21, 2019 6:50 pm
Forum: Rostock MAX v3
Topic: FSR connection to DUET 2 WiFi no workie - config?
Replies: 4
Views: 537

Re: DUET 2 WiFi FSR no workie - config?

YES G! I edited the original post, let me know if you can make sense of it. I'm thinking there's some config like M581: Configure external trigger or M585: Probe Tool (?) that I need to mess with to have the Z-probe get initialized? FWIW, I'm also pinging the Duet3D guys to see what comes up
by nurbie
Tue May 21, 2019 4:01 pm
Forum: Rostock MAX v3
Topic: DUET WiFi E0 / E1 no workie - config?
Replies: 3
Views: 415

Re: DUET WiFi E0 / E1 no workie - config?

What I should say is
M563 P0 D0 S"LDM_01" engaged the stepper(wiring was all fine from the start) and
enabled the controls via Duet GUI:
Screen Shot 2019-05-21 at 2.55.50 PM.png
8-)
by nurbie
Tue May 21, 2019 3:53 pm
Forum: Rostock MAX v3
Topic: DUET WiFi E0 / E1 no workie - config?
Replies: 3
Views: 415

Re: DUET WiFi E0 / E1 no workie - config?

Answer is: \\\ M563 P0 D0 S"LDM_01" ; create a named tool using extruder drive 0 M558 P5 X0 Y0 Z0 H15 F200 I1 ; FSR Settings G31 P500 X0 Y0 Z-0.3 ; Probe trigger value and offsets M270 I1 P1 S0.05 ; Enabled Probe doubletap w/ 0.05mm tolerance M557 R140 S30 ; default bed mapping M501 ; Load saved con...
by nurbie
Mon May 20, 2019 8:44 pm
Forum: Rostock MAX v3
Topic: FSR connection to DUET 2 WiFi no workie - config?
Replies: 4
Views: 537

FSR connection to DUET 2 WiFi no workie - config?

My FSR trinket isn't talking to the DUET2 WiFi. JohnSL board and FSRs all signal properly;using my finger lightly on the build plate the trinket red LEDs light up correctly/individually/averaged depending on pressure location. Should I see anything blinking on the DUET board, or see the Z-probe GUI ...
by nurbie
Mon May 20, 2019 8:30 pm
Forum: Rostock MAX v3
Topic: DUET WiFi E0 / E1 no workie - config?
Replies: 3
Views: 415

DUET WiFi E0 / E1 no workie - config?

RMAX V3 DUET WiFi 2.02 firmware XYZ + endstops/homing all work perfectly PREFACE, I did fudge with the config, adjusted steps to 80, and deleted anything heated/thermistors, bed, and hot-end. Could I have derped it? Ya betcha. The BIG DEALio (fail): The extruder stepper itself is connected to the E0...
by nurbie
Sat May 18, 2019 10:11 pm
Forum: Rostock MAX v3.2
Topic: V3 to 3.2 : DUET v. SMCNC connectors?
Replies: 2
Views: 711

Re: V3 to 3.2 : DUET v. SMCNC connectors?

Nevermind.
Made up new connectors with Duet supplies.

Couldn't pull post...
by nurbie
Fri May 17, 2019 5:47 pm
Forum: Rostock MAX v3.2
Topic: V3.2 Duet access port model file?
Replies: 0
Views: 353

V3.2 Duet access port model file?

Do these Duet cover panel and access 'port/window' models live anywhere on the github archives as .stl/other? I was going to mod the V3 LCD panel / fit the Duet access port to that if so. rostock32_duetpnl_01.jpeg rostock32_duetpnl_02.jpeg also, My current Duet mount places SD access about 3.2cm fro...
by nurbie
Fri May 17, 2019 3:42 pm
Forum: Rostock MAX v3.2
Topic: V3 to 3.2 : DUET v. SMCNC connectors?
Replies: 2
Views: 711

V3 to 3.2 : DUET v. SMCNC connectors?

SMCNC sold out on DUETs so I shopped elsewhere. DUET connectors are warned against in V3.2 assembly walkthrough: When inserting the wires in the white Molex KK connectors, make sure you're using the connectors we sent you in the kit, NOT the ones included in the Duet box! I'm guessing this is becaus...
by nurbie
Fri May 17, 2019 1:46 pm
Forum: Rostock MAX v4
Topic: Dual extrusion feed kits V3/V4
Replies: 3
Views: 527

Re: Dual extrusion feed kits V3/V4

Gracci Mac of the Knifage!
One of my favorite answers.

YES on the Duet .config mod for the one filament drive stepper as well?
I'm going to he Duet forum/instructions to learn about the .config, but might as well ask...
by nurbie
Fri May 17, 2019 12:44 pm
Forum: OTHER Electronics
Topic: Stepper wiring mismatch?
Replies: 5
Views: 2141

Re: Stepper wiring mismatch?

<<Tearing the motors apart isn't a good idea. :)>> Tell me about it! Unfortunately, I don't know how to determine which wires go to what using a volt/ohmeter, so I felt compelled to do the deed before connecting them all up to the freshly unpacked Duet! Would you agree that if I match the wiring to ...
by nurbie
Thu May 16, 2019 7:20 pm
Forum: OTHER Electronics
Topic: Stepper wiring mismatch?
Replies: 5
Views: 2141

Stepper wiring mismatch?

I've got OEM steppers from a V3 kit, and one new one attached to an extruder. 1) want to control them all properly via DUET WiFi board. 2) need to attach a connector to the wires on the new one; wire colors don't match SO, I opened them up to compare wiring + main gear. They look the same, just slig...
by nurbie
Wed May 15, 2019 1:37 pm
Forum: Rostock MAX v4
Topic: Dual extrusion feed kits V3/V4
Replies: 3
Views: 527

Dual extrusion feed kits V3/V4

I have the complete dual filament feed kit for a V3 . Want to use it on a V4. Is the Y splitter and the EZR the same for the V4/SE300? I realize there may be a 0.9 stepper/s on the V4. Can the V3 EZR 1.8 stepper be used by changing a line in the DUET .config to 80(but uniquely/isolated from any othe...
by nurbie
Wed May 15, 2019 11:30 am
Forum: Rostock MAX v3
Topic: v3.2 Stepper Motor upgrade?
Replies: 9
Views: 1346

Re: v3.2 Stepper Motor upgrade?

Thanks for the response. Really looking forward to the Duets! Glad to hear the code/.config side is friendlier than the RAMBo(and has a large, contributing user base). Looks like the right move all around, and as long as my original steppers hang in there, a reasonably economical solution to level u...
by nurbie
Mon May 13, 2019 10:39 am
Forum: Artemis
Topic: Artemis Linear Rail Mainentance
Replies: 5
Views: 3511

Re: Artemis Linear Rail Mainentance

Thank goodness!
by nurbie
Mon May 13, 2019 10:21 am
Forum: Rostock MAX v3
Topic: v3.2 Stepper Motor upgrade?
Replies: 9
Views: 1346

Re: v3.2 Stepper Motor upgrade?

But wait, let's get this straight as I'm shortly modding my V3s to DUET boards, quote: When I updated my v3 to 3.2, I didn't change the motors . It's not a requirement, just a "nice to have". Keep in mind that if you don't change the stepper motors, you'll need to tweak the config.g file for the Due...
by nurbie
Sun May 12, 2019 10:49 pm
Forum: Artemis
Topic: Artemis Linear Rail Mainentance
Replies: 5
Views: 3511

Re: Artemis Linear Rail Mainentance

Gun Butter, I think it's all the same formulation. Personally tested on MTB UltraEndurance rides and semi-automatic weapons. Super bueno! Clean, thin film lubricant. Send me an Artemis and I'll test it ;) (might take a while...) https://gunbutter.com/ WOAH/daym/urp price went up a bit since 2003 whe...

Go to advanced search