Search found 70 matches

by magicmarc
Sat Apr 07, 2018 1:30 pm
Forum: Hacker Series - H2
Topic: H2 Hacker - octoprint advise
Replies: 0
Views: 46

H2 Hacker - octoprint advise

hi, im taking the H2 into my classroom for the students to learn basics... however, since i use cura to slice (and go wireless to my artemis duet board...) id like to also use wireless to go from cura to my H2, .. can someone point me to a good tutorial or video or other to setup the 'octoprint on a...
by magicmarc
Sun Apr 01, 2018 7:21 pm
Forum: Artemis
Topic: how do I change the glass build plate on the Artemis?
Replies: 7
Views: 308

Re: how do I change the glass build plate on the Artemis?

i used this type of spatula, while slightly warm, and slid in under glass at the little half-moon, straight in, then slowly, back and forth, left/right, then sorta popped off (and of course make sure youve turned all 3 plastic holders sideways!)
by magicmarc
Wed Mar 21, 2018 7:07 pm
Forum: Artemis
Topic: CURA plugin to print wirelessly to duet board/atermis
Replies: 15
Views: 608

Re: CURA plugin to print wirelessly to duet board/atermis

the latest plugin version works fine now, v0.0.10
by magicmarc
Tue Mar 20, 2018 8:08 am
Forum: Artemis
Topic: CURA plugin to print wirelessly to duet board/atermis
Replies: 15
Views: 608

Re: CURA plugin to print wirelessly to duet board/atermis

well y'all here always are my saviors, i wish i could help, and down the road ,ill have experience to assist folks here too. im checking the duet3d.com site for me details on the plugin error.
by magicmarc
Tue Mar 20, 2018 7:27 am
Forum: Artemis
Topic: print has a small little seam or notch in same spot on multiple prints of same item
Replies: 7
Views: 257

Re: print has a small little seam or notch in same spot on multiple prints of same item

thanks, im a little confused as to what to set the settings to, and which one to change, id like the layer height to change on the inner wall perhaps, not the outer wall. but im not sure where to chage and what to try changing to... ive attached a pic of the section 'travel' in the cura. i do see th...
by magicmarc
Mon Mar 19, 2018 3:13 pm
Forum: Artemis
Topic: print has a small little seam or notch in same spot on multiple prints of same item
Replies: 7
Views: 257

Re: print has a small little seam or notch in same spot on multiple prints of same item

ahh, thanks, i do use cura 3.2.1, do you know what exactly that setting is called/named in cura? (and/or where exactly it is?)
thanks
marc
by magicmarc
Mon Mar 19, 2018 3:12 pm
Forum: Artemis
Topic: CURA plugin to print wirelessly to duet board/atermis
Replies: 15
Views: 608

Re: CURA plugin to print wirelessly to duet board/atermis

thanks bones, changing the namee of the folder worked, it recognizes there duet rff is there as extension... however when i went to upload a file to the artemis (after editing the correct wifi ip address) it says 'network error "" 301 incorrect protocol... ideas (i am using a sonicwall tz3...
by magicmarc
Mon Mar 19, 2018 2:42 pm
Forum: Artemis
Topic: CURA plugin to print wirelessly to duet board/atermis
Replies: 15
Views: 608

Re: CURA plugin to print wirelessly to duet board/atermis

thanks bones, i thought the latest plugin ver 0.0.9 was supposed to work with cura 3.2.1...
ill try changing the name now, and see if it recognizes the plugin!
marc
by magicmarc
Mon Mar 19, 2018 9:56 am
Forum: Artemis
Topic: print has a small little seam or notch in same spot on multiple prints of same item
Replies: 7
Views: 257

print has a small little seam or notch in same spot on multiple prints of same item

hi, ive got a little stand/nameplate i use to mount items. i printed several of them up this weekend, and i noticed that in the same spot, on each print there is a little 'seam' or 'notch' printing. ive attached the picturs to show y'all. obv. its not there in the original tinkercad file or the cura...
by magicmarc
Mon Mar 19, 2018 9:49 am
Forum: Artemis
Topic: CURA plugin to print wirelessly to duet board/atermis
Replies: 15
Views: 608

Re: CURA plugin to print wirelessly to duet board/atermis

ok, so gene, i tried to install the latest duet-wifi-rff plugin for cura 3.2.1 (Cura-DuetRRFPlugin-0.0.5), i got this from the link listed below for the cura duetwifi. basically unzipped the folder, and placed it in the /program files/ultimaker cura 3.2.1/plugins folder but when i oppen cura its not...
by magicmarc
Sun Mar 18, 2018 6:34 pm
Forum: Artemis
Topic: CURA plugin to print wirelessly to duet board/atermis
Replies: 15
Views: 608

Re: CURA plugin to print wirelessly to duet board/atermis

hi gene, i had to reinstall the cure, ill reinstall the duet rff plugin and try again, then ill post the config file.
thanks
marc
by magicmarc
Fri Mar 02, 2018 9:29 am
Forum: Artemis
Topic: CURA plugin to print wirelessly to duet board/atermis
Replies: 15
Views: 608

Re: CURA plugin to print wirelessly to duet board/atermis

hi in installed the duetRRF plugin into cura, and when i goto print to artemis, vie the duetrrf, it gives me a 'network error - protocol'. and when i goto the extension portion of cura to edit the parameters for the duetrrf plugin, its asking for the duet board username and password,,, is there a de...
by magicmarc
Fri Mar 02, 2018 7:25 am
Forum: Troubleshooting
Topic: CURA OBJECT GCODE - LOOKS WRONG WHEN OPENED IN MATTERCONTROL TO PRINT
Replies: 5
Views: 153

Re: CURA OBJECT GCODE - LOOKS WRONG WHEN OPENED IN MATTERCONTROL TO PRINT

thanks gene, im not familiar with octoprint, repetier host, or pronterface, but i will look them up this weekend and learn a bit... and try.. today im going to try just the sd card direct print, no mattercontrol (cura>>file>>sd card>>H@ insert & print) as always, i learn something new and import...
by magicmarc
Thu Mar 01, 2018 12:57 pm
Forum: Hacker Series - H2
Topic: print problem, printing a spinning top with tower top, tower comes out wrong
Replies: 7
Views: 712

Re: print problem, printing a spinning top with tower top, tower comes out wrong

THAKNS AS ALWAYS GENE AND EVERYONE. I WILL TRY THE SD CARD PRINT TODAY/TONIGHT.
AS WELL IS THERE A GOOD YOUTUBE LINK OR INSTRUCTIONS TO USE OCTOPRINT?
THANKS
by magicmarc
Thu Mar 01, 2018 9:17 am
Forum: Troubleshooting
Topic: CURA OBJECT GCODE - LOOKS WRONG WHEN OPENED IN MATTERCONTROL TO PRINT
Replies: 5
Views: 153

Re: CURA OBJECT GCODE - LOOKS WRONG WHEN OPENED IN MATTERCONTROL TO PRINT

gene this one isnt a print top swilling error, like the spinning top that was too hot and/or too fast/ or too little layer time... this was merely opening a .stl in cura, with the slicing profiles for the H2, then saving as gcode, then importing the gode to matercontrol, no print, as soon as it was ...
by magicmarc
Thu Mar 01, 2018 8:38 am
Forum: Hacker Series - H2
Topic: print problem, printing a spinning top with tower top, tower comes out wrong
Replies: 7
Views: 712

Re: print problem, printing a spinning top with tower top, tower comes out wrong

im using mattercontrol to slice and print to h2 hacker.
im having error using cura to slice and mattrercontrol to upload gcode and print, the gcode generated from cura looks and is wrong when added to the que in mattercontrol.
by magicmarc
Thu Mar 01, 2018 8:36 am
Forum: Troubleshooting
Topic: CURA OBJECT GCODE - LOOKS WRONG WHEN OPENED IN MATTERCONTROL TO PRINT
Replies: 5
Views: 153

CURA OBJECT GCODE - LOOKS WRONG WHEN OPENED IN MATTERCONTROL TO PRINT

HI, I'M TRYING TO DO THE SIMPLE BENCHY PRINT ON THE H2 DELTA. I OPENED THE FILE IN CURA 3.2.1, USING THE SLICING PROFILES FOR THE HE280 DEFAULT AND THE 140X140X295, 0.5 1,75 PRINTER SETTINGS, THEN ALL LOOKS GOOD, I EXPORT THE BENCHY GCODE FILE. WHEN I OPEN IT IN MATTERCONTROL TO PRINT IT LOOKS FLAT,...
by magicmarc
Tue Feb 27, 2018 2:44 pm
Forum: Hacker Series - H2
Topic: print problem, printing a spinning top with tower top, tower comes out wrong
Replies: 7
Views: 712

Re: print problem, printing a spinning top with tower top, tower comes out wrong

thanks everyone, im going to slow it down now, and cool it down, with temp and fans.
thx
marc
by magicmarc
Tue Feb 27, 2018 9:13 am
Forum: Hacker Series - H2
Topic: print problem, printing a spinning top with tower top, tower comes out wrong
Replies: 7
Views: 712

print problem, printing a spinning top with tower top, tower comes out wrong

hi, the base of the spining top prints right, then it gets to the tower part, and after a short bit the print screws up, as shown in the picture. this is standard pla, 0.2 layer, 20 % infill (i also tried 15% same thing happens) i also tried different temps, 210, 215, 220, etc.. same hting happens.....
by magicmarc
Mon Feb 26, 2018 7:34 pm
Forum: Hacker Series - H2
Topic: Base heater thermistor
Replies: 3
Views: 357

Re: Base heater thermistor

hmmm i built the H2, and it didnt have a heated bed included stock... ?
by magicmarc
Thu Feb 22, 2018 8:51 am
Forum: Artemis
Topic: Error: during calibration after print errors
Replies: 5
Views: 347

Re: Error: during calibration after print errors

thanks for the help as always gene! without the community id be nowhere. the artemis has been printing all day, doing little projects ive had, trying it out... its cranking. i do notice a little rattle or vibration coming from the hot end cooling fans.. i notice one of them the thin bottom corner fl...
by magicmarc
Tue Feb 20, 2018 5:34 pm
Forum: Artemis
Topic: Error: during calibration after print errors
Replies: 5
Views: 347

Re: Error: during calibration after print errors

cura. the first few i did cam out great, i am noticing the carriages seem louder moving around... how would i check the stepper motor connectors, on the arduino boar on top i assume marc trying it cold now g32 i checked the stepper motor connectors in the board, seemed solid, all 3 sets. then did th...
by magicmarc
Tue Feb 20, 2018 1:51 pm
Forum: Artemis
Topic: Error: during calibration after print errors
Replies: 5
Views: 347

Error: during calibration after print errors

got a few print errors after doing the same print twice fine. then did another pid tune and m500 saved, then did the g32 to calibrate and got and error as follows: Height Error Diff(0.15) above maximum tolerance (0.05) retrying.. THE 0.15 NUMBER CHANGES A BIT EACH TIME I PROBE OR G32... in the pics ...
by magicmarc
Mon Feb 19, 2018 1:31 pm
Forum: Artemis
Topic: CURA plugin to print wirelessly to duet board/atermis
Replies: 15
Views: 608

CURA plugin to print wirelessly to duet board/atermis

thanks to the FBook group members, as well as Ryan & Joseph, i was able to overcome some assembly obstacles and time constraints to complete my atremis build. the firstprint.gcode for benchy came out great! better than my current H2 ever has printed! i read in a post there is a plugin for cura f...

Go to advanced search