Search found 10 matches

by trublu289
Tue Apr 10, 2018 7:34 am
Forum: Troubleshooting
Topic: Print quality woes
Replies: 15
Views: 1702

Re: Print quality woes

Figured out the issue finally. I changed the effector to one that put the motor and extruder right below. I did lose some height but there's no more wobble. The one I had on before had the motor sitting above and the arms were farther out. This is the current effector with dual fans. https://www.thi...
by trublu289
Mon Mar 12, 2018 12:29 am
Forum: Troubleshooting
Topic: Print quality woes
Replies: 15
Views: 1702

Re: Print quality woes

I have the the speeds down already. The motor motor rocks slightly on certain moves. With circles the ringing shows the most. On other prints not really a issue. Weird indeed.
by trublu289
Sun Mar 04, 2018 7:15 pm
Forum: Troubleshooting
Topic: Print quality woes
Replies: 15
Views: 1702

Re: Print quality woes(update)

Ok so I changed out the power supply from the atx to a 12v 20a regulated supply and the heated bed heats up pretty quickly. I've also switched the heater wires to the noodle like silicone wire. The ringing is still there even with .9 titan aero and new ball cup arm upgrade. From the looks of it when...
by trublu289
Sun Dec 31, 2017 4:25 pm
Forum: Troubleshooting
Topic: Print quality woes
Replies: 15
Views: 1702

Re: Print quality woes

In the process of upgrading will report back once complete.
by trublu289
Wed Dec 13, 2017 10:44 pm
Forum: Troubleshooting
Topic: Print quality woes
Replies: 15
Views: 1702

Re: Print quality woes

I've dialed back the flow a bit to 95 percent. The heated bed can get to about 95 96 but I can't get it to go any higher. I changed my heated bed wiring to 10 gauge as I had the infamous terminal block melting. I have cooling enabled, some parts would deform with abs. I've never used matter control....
by trublu289
Sun Dec 10, 2017 11:46 pm
Forum: Troubleshooting
Topic: Print quality woes
Replies: 15
Views: 1702

Re: Print quality woes

I forgot that print was in abs. I was under the impression that I didn't have to do rafts and brims with pei. I do have the berd air max and it was on partially. My bed is maxing out at 95.
by trublu289
Mon Dec 04, 2017 7:22 am
Forum: Troubleshooting
Topic: Print quality woes
Replies: 15
Views: 1702

Print quality woes

Hello all. Just recently upgraded my rostock max v2 with a titan aero , pei bed and ballcup arms. My prints thus far have improved but I'm stilling having a issue with 1 corner lifting on abs and corners not as sharp as they should be. Also there seems to be slight ringing. Can anyone chime in on tr...
by trublu289
Mon Mar 06, 2017 3:32 pm
Forum: Troubleshooting
Topic: Time out
Replies: 0
Views: 184

Time out

I'm having issues using repetier host. It works when first connected but after a while it just stops responding to controls and takes a while to actually respond after a long time. Changed cache ,various settings and usb cable still no go.
by trublu289
Mon Mar 06, 2017 1:29 pm
Forum: New Member introduction
Topic: Greetings
Replies: 2
Views: 498

Re: Greetings

I'm having issues with connectivity repetier keeps timing out not sure what's going on. All parts stock. I just printed the peek fan on another printer.
by trublu289
Mon Mar 06, 2017 11:00 am
Forum: New Member introduction
Topic: Greetings
Replies: 2
Views: 498

Greetings

Hello all just recently acquired a second hand rostock max 2 and figured now is a good time to join the forum as a lot of this is rather new and my first delta. Hope to learn a lot. My name is Brandon or bj I'm a tinkerer, engineer and much more. Looking forward to chatting with you guys.

Go to advanced search