Search found 24 matches

by Bones056
Wed Jun 06, 2018 10:18 pm
Forum: Artemis
Topic: HEATER 1 Fault
Replies: 4
Views: 451

Re: HEATER 1 Fault

I have a ton of hours on my Artemis.. Out of no where I started to get Heater Faults.. Traced it to the Red & Black wires that go into the White connector on the SE300. Pushed them back in and have had no Hearter Faults since... I try to check the connector every week and I do find that the wire...
by Bones056
Thu May 24, 2018 8:00 pm
Forum: Artemis
Topic: Lubricating linear rails?
Replies: 10
Views: 880

Re: Lubricating linear rails?

JayDee I was beginning to think I was the only one.. ;-) with that terrible squeak!! I thought I could get away with some lub only... Squeak came back so I opted for the nylon spacers.. Had to work on them to fit the bearing so I could tighten without locking the Idler up. Haven't had the squeak sin...
by Bones056
Mon Mar 19, 2018 3:26 pm
Forum: Artemis
Topic: CURA plugin to print wirelessly to duet board/atermis
Replies: 15
Views: 875

Re: CURA plugin to print wirelessly to duet board/atermis

Sorry... can't help you with that..
by Bones056
Mon Mar 19, 2018 2:33 pm
Forum: Artemis
Topic: CURA plugin to print wirelessly to duet board/atermis
Replies: 15
Views: 875

Re: CURA plugin to print wirelessly to duet board/atermis

Just a heads up on using Cura 2.3.1 with the Artemis.... I had a lot of problems trying to use that version. I had to go back to 3.1.
by Bones056
Mon Mar 19, 2018 2:31 pm
Forum: Artemis
Topic: CURA plugin to print wirelessly to duet board/atermis
Replies: 15
Views: 875

Re: CURA plugin to print wirelessly to duet board/atermis

I believe that you need to change the folder name from Cura-DuetRRFPlugin-0.0.5 to Cura-DuetRRFPlugin-master. That should do it for you....
by Bones056
Wed Mar 07, 2018 3:01 pm
Forum: Artemis
Topic: Lubricating linear rails?
Replies: 10
Views: 880

Re: Lubricating linear rails?

I never had a scraping sound... just a very irritating squeak at low head speeds. Like when the head is going back and forth for a base layer. Gone now..
by Bones056
Wed Mar 07, 2018 12:52 pm
Forum: Artemis
Topic: Lubricating linear rails?
Replies: 10
Views: 880

Re: Lubricating linear rails?

20180307_093153.jpg Two of the three idler pulleys looked like this... Went to local hardware store and picked up some small nylon washers. Had to take a file to round one of the edges down so it would fit the idler pulley bearing better. Then assembled it back up by tightening till it just becomes...
by Bones056
Tue Mar 06, 2018 11:05 pm
Forum: Artemis
Topic: Lubricating linear rails?
Replies: 10
Views: 880

Re: Lubricating linear rails?

This was a tuff one to trace.... and it was driving me nuts. I love the printer!! Every now and then when the HotEnd would move slowly. I would hear what sounded like a linear rail squeaking. I put some light machine oil on all the rails and still had the squeak when the head moved slowly. I tired t...
by Bones056
Mon Feb 05, 2018 11:10 am
Forum: Artemis
Topic: adarcher's build/troubleshooting
Replies: 87
Views: 4769

Re: First homing: horrible grinding sounds

And How do we get to that 16 point Cal? Is that the Mesh Grid Compensation? Thanks
by Bones056
Fri Jan 26, 2018 4:36 pm
Forum: Artemis
Topic: Where are all of the detailed Artemis reviews?
Replies: 7
Views: 737

Re: Where are all of the detailed Artemis reviews?

Have had the Artemis for around a month. The best 3D printer I have ever used! Fast, Quiet, and "Fun" to use!!. Beautiful prints every time! Have been printing everyday for at least 6 hours per day and more. The more I use it... the more I like it! Getting use to using Cura 3.1.0. With the...
by Bones056
Wed Dec 28, 2016 10:28 am
Forum: Rostock MAX v3
Topic: SeeMeCNC Slicing Profiles
Replies: 3
Views: 638

SeeMeCNC Slicing Profiles

I see that there are some new slicing profiles located in the SeeMeCNC Repositories. I'm trying to load the RostockMax V3 Cura profiles. Not having much luck loading into MatterControl. Are these Cura Profiles for a stand alone version of Cura? Would like to know before I go downloading & instal...
by Bones056
Fri Nov 18, 2016 7:01 pm
Forum: Rostock MAX v3
Topic: A few build notes for the RostockMAX v3 Aficionado
Replies: 28
Views: 3168

Re: A few build notes for the RostockMAX v3 Aficionado

Here's a Whip Clip you can print to keep the HE280 plug from coming out. We'll make an injection mold this next week to include them. The printed one works great. http://repables.com/r/808 I can't seem to print a viable copy of the holder. I have tried PLA and ABS, the 4 parts that are like legs br...
by Bones056
Thu Nov 17, 2016 9:42 pm
Forum: Rostock MAX v3
Topic: A few build notes for the RostockMAX v3 Aficionado
Replies: 28
Views: 3168

Re: A few build notes for the RostockMAX v3 Aficionado

Thanks, Printing one now!!
by Bones056
Wed Nov 16, 2016 7:46 pm
Forum: Show us your machine!
Topic: Not allowed
Replies: 13
Views: 2094

Re: Not allowed

That printer is a revised BI V2.5 from Boots Ind. I have one of those that is need of some revising to get it working again.
by Bones056
Wed Nov 16, 2016 3:26 pm
Forum: Rostock MAX v3
Topic: A few build notes for the RostockMAX v3 Aficionado
Replies: 28
Views: 3168

Re: A few build notes for the RostockMAX v3 Aficionado

I think I have finally figured out what happened when my machine stopped running. After a whole lot of testing... It looks like I had torqued the connector on the hot end enough to cause the machine to sense a problem. I went through all the wiring and connectors and found no issues. I had moved the...
by Bones056
Wed Nov 16, 2016 3:13 pm
Forum: Show us your machine!
Topic: Not allowed
Replies: 13
Views: 2094

Re: Not allowed

Tome it look like either F1 or Indy Car!
by Bones056
Mon Nov 14, 2016 7:50 pm
Forum: Rostock MAX v3
Topic: A few build notes for the RostockMAX v3 Aficionado
Replies: 28
Views: 3168

Re: A few build notes for the RostockMAX v3 Aficionado

Should have said this in the post. That's the first check I made.. Every connection in the bottom and top is secure. Harness was plugged in and not loose. Only thing I didn't check was the Hot End stuff. Tomorrow I will start a print and kick the table again to see what happens. There was no power l...
by Bones056
Mon Nov 14, 2016 5:35 pm
Forum: Rostock MAX v3
Topic: A few build notes for the RostockMAX v3 Aficionado
Replies: 28
Views: 3168

Re: A few build notes for the RostockMAX v3 Aficionado

Here's one for you all.... I have been running the Dev Build since Friday. Printing almost nonstop. Things have been going great until I kicked the table that the printer is on and the printer stopped running and the bed & hot end shut down! So my question is this. Does the board that does the c...
by Bones056
Fri Nov 11, 2016 11:00 am
Forum: Rostock MAX v3
Topic: A few build notes for the RostockMAX v3 Aficionado
Replies: 28
Views: 3168

Re: A few build notes for the RostockMAX v3 Aficionado

Here's how I handled the clip problem.... Had to add 3 layers of Blue Painter Tape at each clip to get the glass to stay put!
by Bones056
Thu Nov 10, 2016 3:47 pm
Forum: Rostock MAX v3
Topic: P003A HE280 [Solved?] Auto Leveling Issue/Bed Leveling Issue/Calibration
Replies: 134
Views: 17259

Re: P003A HE280 [Solved?] Auto Leveling Issue/Bed Leveling Issue/Calibration

Here are the results from my testing that I performed today. I've included the hires picture in a zip file and a pdf of my results and how I did it. If you have any questions.... let me know. I will get back as soon as I can.

Jeff
by Bones056
Tue Nov 08, 2016 9:13 pm
Forum: Rostock MAX v3
Topic: P003A HE280 [Solved?] Auto Leveling Issue/Bed Leveling Issue/Calibration
Replies: 134
Views: 17259

Re: P003A HE280 [Solved?] Auto Leveling Issue/Bed Leveling Issue/Calibration

When that big print finishes tomorrow at around 7PM. I will separate the End Stop Wiring form the Stepper Motor Wiring. I have them tucked together in a bundle to clean the top up. I will also run 3 cal's like mhackney did with the Ferrite on, Ferrite off, and then I will do one after I separate out...
by Bones056
Tue Nov 08, 2016 4:32 pm
Forum: Rostock MAX v3
Topic: P003A HE280 [Solved?] Auto Leveling Issue/Bed Leveling Issue/Calibration
Replies: 134
Views: 17259

Re: P003A HE280 [Solved?] Auto Leveling Issue/Bed Leveling Issue/Calibration

Here is a large print to test if things are any better. I still have the problem at the x tower being a tad thin. Based on Cloneit3d, looks like things are moving at the company level. Will not do any more testing as it sounds like there may be a fix close at hand...
by Bones056
Tue Nov 08, 2016 9:23 am
Forum: Rostock MAX v3
Topic: P003A HE280 [Solved?] Auto Leveling Issue/Bed Leveling Issue/Calibration
Replies: 134
Views: 17259

Re: P003A HE280 [Solved?] Auto Leveling Issue/Bed Leveling Issue/Calibration

Stopped by my local RadioShack and found that they sell three sizes of Ferrite Beads. I bought all three sizes, each size has two per pack. When I got home I used the Small 3.5mm ID for the Rambo Board. The largest which has 3/8 ID was used at the Hot End. So far things are looking better at the edg...

Go to advanced search