Search found 14 matches

by felich
Tue Jun 12, 2018 7:56 pm
Forum: Artemis
Topic: HEATER 1 Fault
Replies: 4
Views: 716

Re: HEATER 1 Fault

I am not satisfied with wiggling wires to make it work for a while. I am making large prints that each use up $20 of filament. I have to start each print with a full roll so an aborted print is not just a waste of my time. The heater connector looks under rated for the current it carries. I am think...
by felich
Wed Jun 06, 2018 6:40 pm
Forum: Artemis
Topic: HEATER 1 Fault
Replies: 4
Views: 716

HEATER 1 Fault

Artemis was printing away (using PETG) at 250 degrees when the hotend temperature plot went through very rapid plus and minus 30 degree swings and then threw a "Heater 1 Fault" and shut down the heater. I cycled the power on Artemis and restarted my print with no faults. Now I worry that i...
by felich
Wed May 02, 2018 4:46 pm
Forum: Development Topics
Topic: Artemis Browser Interface
Replies: 5
Views: 1757

Re: Artemis Browser Interface

I don't see it. Please point it out.
Screen Shot.jpg
by felich
Tue May 01, 2018 2:31 pm
Forum: Development Topics
Topic: Artemis Browser Interface
Replies: 5
Views: 1757

Artemis Browser Interface

I could not find a place in the forum specifically for software change requests, so I hope this a good place to put this thread. I have what I feel is an important request. Please add the file date to the information shown in the G-Code file listing. I am never certain that I have the latest G-Code ...
by felich
Wed Jan 17, 2018 8:14 pm
Forum: Artemis
Topic: First Probe
Replies: 3
Views: 234

Re: First Probe

wepollock, Most Excellent, Thanks. Your macro was a big help. I got down to -.35. Now my G0Z0 comes out perfect! So in the Configuration Guide Step Five where is says "If it's too loose, run the following GCode: "G31 P500 X0 Y0 Z-0.25"" I believe it should say "If it is too ...
by felich
Wed Jan 17, 2018 6:24 pm
Forum: Artemis
Topic: First Probe
Replies: 3
Views: 234

First Probe

I have moved on to the First Probe. After calibration I did a GoZo with a piece of printer paper on the bed. The tip comes down slowly and then there is a "tink" as it stops. The paper is held so tightly that it tears when moved. So I ran another First Probe and then another. The tip still...
by felich
Wed Jan 17, 2018 6:04 pm
Forum: Artemis
Topic: First batch of Artemis is out the door.
Replies: 6
Views: 488

Re: First batch of Artemis is out the door.

SD chip wasn't seated properly.
AOK now.
by felich
Wed Jan 17, 2018 5:39 pm
Forum: Artemis
Topic: No joy with browser connection
Replies: 19
Views: 1558

Re: No joy with browser connection -Solved now!

Well I unmounted the controller and removed the SD chip and looked at it on my PC. Everything looked OK far as I could tell. I remounted the controller and inserted the SD chip. BAM! The web page loaded first try. So I guess the SD chip was not inserted to its satisfaction, but re-inserting it made ...
by felich
Tue Jan 16, 2018 1:53 pm
Forum: Artemis
Topic: First batch of Artemis is out the door.
Replies: 6
Views: 488

Re: First batch of Artemis is out the door.

I am the guy that received the RTP.
I am having no luck seeing the web page.
Please see my post "No joy with browser connection"
Thanks for any help you can provide.
by felich
Tue Jan 16, 2018 1:38 pm
Forum: Artemis
Topic: No joy with browser connection
Replies: 19
Views: 1558

Re: No joy with browser connection

Here is the latest information on this issue: I shut down the WiFi with M552 S0 I re-sent M587 with S"studio" P"password" I10.0.0.89 J10.0.0.1 K255.255.255.0 Then: m552 S1 ok m552 WiFi module is connected to access point studio, IP address 10.0.0.89 ok m553 Net mask: 255.255.255....
by felich
Mon Jan 15, 2018 9:47 pm
Forum: Artemis
Topic: No joy with browser connection
Replies: 19
Views: 1558

Re: No joy with browser connection

Where do I find the Artemis documentation?
by felich
Sun Jan 14, 2018 6:29 pm
Forum: Artemis
Topic: No joy with browser connection
Replies: 19
Views: 1558

Re: No joy with browser connection

I shut down Artemis and still got a reply from pinging 10.0.0.232 so it looks like a DHCP issue. However, I don't know which machine is using 10.0.0.232 so I can't change it on that end. Is there a way to set a static IP address on Artemis? Also, where can I find all of these mysterious M codes you ...
by felich
Fri Jan 12, 2018 6:03 pm
Forum: Artemis
Topic: No joy with browser connection
Replies: 19
Views: 1558

Re: No joy with browser connection

I don't see anything about RSSI. Used output buffers: 1 of 32 (9 max) === Platform === RepRapFirmware for Duet WiFi version 1.19.2 running on Duet WiFi 1.0 Board ID: 08DGM-95BNL-MGPSJ-6JKFG-3SJ6Q-T1W7Y Static ram used: 21176 Dynamic ram used: 95552 Recycled dynamic ram: 2056 Stack ram used: 4056 cur...
by felich
Fri Jan 12, 2018 5:16 pm
Forum: Artemis
Topic: No joy with browser connection
Replies: 19
Views: 1558

No joy with browser connection

I just plugged in my RTP Artemis and went through the Configuring Artemis procedure. Wifi enables fine. YAT reports: ok<LF>Wifi module is connected to access point studio, IP address 10.0.0.232<LF> Step 3 says:Open a new tab and enter the IP Address of your printer. When the page loads, click on &qu...

Go to advanced search