Search found 62 matches

by javiercordero20
Sun Sep 03, 2017 6:08 pm
Forum: Rostock MAX v3
Topic: FIRMWARE - Marlin Firmware for Rostock V3 with Proximity Probe
Replies: 0
Views: 639

FIRMWARE - Marlin Firmware for Rostock V3 with Proximity Probe

Hello All,

I am planning on swapping the RAMBo board for a different board soon. I am also working with someone to make a new effector with a proximity probe. I am having some trouble converting the SeeMeCNC stock firmware to new [clean] marlin.

Can anyone gimme a hand?
by javiercordero20
Wed Jan 18, 2017 11:46 am
Forum: General Announcments
Topic: Sad day guys - Eaglezsoar has left us
Replies: 34
Views: 11942

Re: Sad day guys - Eaglezsoar has left us

My condolences. :(
by javiercordero20
Thu Jan 12, 2017 11:25 pm
Forum: Rostock MAX v3
Topic: Stepper Stuttering
Replies: 1
Views: 585

Stepper Stuttering

Hello all, Today I turned on my printer to an odd problem. When I run G28/G29 and the printer is homing. it can sometimes do an odd mid movement stutter and it has even once rebooted the RAMBo during such an event. Anyone have any advice where I should start looking for the problem and what the prob...
by javiercordero20
Sat Dec 03, 2016 2:40 pm
Forum: Rostock MAX v3
Topic: Rostock Max v3 calibrating script.
Replies: 41
Views: 14575

Re: Rostock Max v3 calibrating script.

Hello,

I wondered if its possible to do more points during calibration? E.G instead of only the 3 tower points it does 6 points

-Javier.
by javiercordero20
Sun Nov 27, 2016 10:13 pm
Forum: Filament
Topic: PETG Calibration
Replies: 18
Views: 6704

Re: PETG Calibration

IMBoring25 wrote:OK, that one can do 255. Other than 255 hot end and 70 bed, I'm just using my standard E3D ABS settings. 2mm, 10mm/s retracts, which I believe are also appropriate for the HE280, if you're using something else.



What about your extrusion multiplier?
by javiercordero20
Sun Nov 27, 2016 10:32 am
Forum: Filament
Topic: PETG Calibration
Replies: 18
Views: 6704

Re: PETG Calibration

IMBoring25 wrote:What hot end are you running?


The stock hotend that comes with the Rostock Max V3.
by javiercordero20
Sun Nov 27, 2016 2:41 am
Forum: Rostock MAX v3
Topic: Backpressure Issue
Replies: 49
Views: 4705

Re: Backpressure Issue

Hello,

Just wanted to say this issue is closed and therefore this thread has ended. Backpressure issue was retraction speed and/or length.
by javiercordero20
Sun Nov 27, 2016 2:09 am
Forum: Filament
Topic: PETG (PET)
Replies: 13
Views: 4829

Re: PETG (PET)

Hello guys, Has anyone tried printing PETG on a Rostock Max v3? I am trying to dail it in now and I have some issues. I managed to get the first layer to stick directly on glass and with some hairspray but notice that the second pass (layer 2) usually turns into a mess with stuff sticking to the noz...
by javiercordero20
Sun Nov 27, 2016 1:41 am
Forum: Filament
Topic: PETG Calibration
Replies: 18
Views: 6704

Re: PETG Calibration

I use a 255C hot end for PETG but you may not want to do that depending on what hot end you're running. Hello there, Now that I got PLA printing nicely and got many prints done so far. I am back to fighting with PETG. Could you share your settings so I can use them as a guide to calibrate my filame...
by javiercordero20
Wed Oct 19, 2016 9:35 pm
Forum: GCode & Test Prints
Topic: Feedback on print quality
Replies: 12
Views: 3044

Re: Feedback on print quality

Hello All, I'd love some feedback on this print. I am working to get the perfect PLA settings for my printer. I see defects on the side of the print and I need to find a way to make the supports easier to remove. They are too tight to the print. These three fan shrouds were printed together. The fan...
by javiercordero20
Tue Oct 18, 2016 10:48 pm
Forum: Rostock MAX v3
Topic: Part fan modification for tight enclosure
Replies: 23
Views: 10292

Re: Part fan modification for tight enclosure

Howdy!

I am busy printing these fan shrouds to focus the cooling so my smaller prints don't have a cooling issue anymore.

Would be better if it used radial fans for better air volume.
by javiercordero20
Mon Oct 17, 2016 3:37 pm
Forum: Filament
Topic: PETG Calibration
Replies: 18
Views: 6704

Re: PETG Calibration

Hello, Here is the test cube that I printed using KISSlicer. It has some weird artifacts on two of the four corners and the bottom layer looks bad due to not being primed enough. (the top of the image is actually the bottom layer) IMG_0004.JPG In the slicer I noticed that when I look at the layers. ...
by javiercordero20
Mon Oct 17, 2016 3:02 pm
Forum: Filament
Topic: PETG Calibration
Replies: 18
Views: 6704

Re: PETG Calibration

Try youtube. https://www.youtube.com/watch?v=zVpzIj3G6ow Hello there, Just saw that video. Beat you to it. The thing that adds to the confusion for me is the terminology I am used to is not mentioned in KISSlicer. So it makes it a little hard to understand. I'll keep looking. Right now I am trying ...
by javiercordero20
Mon Oct 17, 2016 2:44 pm
Forum: Filament
Topic: PETG Calibration
Replies: 18
Views: 6704

Re: PETG Calibration

I can't tell if you are using MatteSlice or Cura, if MS switch to Cura. If Cura, seriously consider KISS. KISS has a "crossover" perimeter start/stop path that really cuts down on zits. It's the only slicer that does this. Hello, KISSslicer is confusing. I am currently playing with the se...
by javiercordero20
Mon Oct 17, 2016 1:01 am
Forum: Filament
Topic: PETG Calibration
Replies: 18
Views: 6704

Re: PETG Calibration

IMBoring25 wrote:I use a 255C hot end for PETG but you may not want to do that depending on what hot end you're running.


I tried playing with the temperature but that doesn't solve the zits/globbing.
by javiercordero20
Mon Oct 17, 2016 12:40 am
Forum: Filament
Topic: PETG Calibration
Replies: 18
Views: 6704

PETG Calibration

Hello All, I am trying to calibrate to print my several PETG rolls. However I have an issue I cannot with random globbing in and on my prints. The following are several attempted prints with slightly tweaked settings to see if the globbing would go away with no luck. IMG_0001.JPG Here are the settin...
by javiercordero20
Wed Oct 12, 2016 1:37 pm
Forum: Troubleshooting
Topic: Rostock V3 Bed issue
Replies: 77
Views: 7007

Re: Rostock V3 Bed issue

What exactly do you do with the points that are pulled from the bedfile generator? Mr. Hackney could you please explain what we need to do with the points generated? What you do is you would edit the file that describes the bed probing points (bed.g on the duet). These points are inserted as differ...
by javiercordero20
Wed Oct 12, 2016 12:17 pm
Forum: Troubleshooting
Topic: Rostock V3 Bed issue
Replies: 77
Views: 7007

Re: Rostock V3 Bed issue

ComJak wrote:What exactly do you do with the points that are pulled from the bedfile generator?


Mr. Hackney could you please explain what we need to do with the points generated?
by javiercordero20
Tue Oct 11, 2016 10:47 am
Forum: Rostock MAX v3
Topic: Backpressure Issue
Replies: 49
Views: 4705

Re: Backpressure Issue

Slow down, be consistent and work through everything carefully. Others will jump in to help and I will as well but you've got to get on the right track asap! I still suspect an issue with inserting the Bowden in the hot end. Something you are doing or did in the build is not quite right. Hello, Fir...
by javiercordero20
Tue Oct 11, 2016 10:36 am
Forum: Rostock MAX v3
Topic: Backpressure Issue
Replies: 49
Views: 4705

Re: Backpressure Issue

I think you are all over the map. What would possess you to run PLA at 250°C??? We had things working perfectly on Saturday and then you immediately changed everything and failed. Slow down, go back to basics. I am sure you still have not read the post I've asked you t read multiple times. I'm out ...
by javiercordero20
Mon Oct 10, 2016 11:01 pm
Forum: Rostock MAX v3
Topic: Backpressure Issue
Replies: 49
Views: 4705

Re: Backpressure Issue

I don't recommend switching filament. I am now doing the 100mm Extrusion test. @250C I can extrude 100mm without skipping. (I am aware 250C is extremely hot. no PLA should be that hot. But it was where I started) @200C it skips. it does not extrude the 100mm cleanly. I did the same test with a seco...
by javiercordero20
Mon Oct 10, 2016 10:54 pm
Forum: Rostock MAX v3
Topic: Backpressure Issue
Replies: 49
Views: 4705

Re: Backpressure Issue

mhackney wrote:I don't recommend switching filament.


Alright.
by javiercordero20
Mon Oct 10, 2016 10:49 pm
Forum: Rostock MAX v3
Topic: Backpressure Issue
Replies: 49
Views: 4705

Re: Backpressure Issue

There could've been a small piece of debris in the filament or maybe a little shard of metal from the hot end or extruder. I've found a few weird things in filament. Hello, I can switch out the filament but I don't have any other regular PLA. I have: PETG CF-PETG GLow in the dark PLA I have printed...
by javiercordero20
Mon Oct 10, 2016 10:44 pm
Forum: Rostock MAX v3
Topic: Backpressure Issue
Replies: 49
Views: 4705

Re: Backpressure Issue

But a clogged nozzle does not explain your "first try" that seemed to be jammed with no nozzle installed. How would that be explained? Hello, I suspect that there was a small clog of filament somewhere that got unclogged when I was flushing the nozzleless hotend with filament. Sincerely, ...
by javiercordero20
Mon Oct 10, 2016 10:42 pm
Forum: Rostock MAX v3
Topic: Backpressure Issue
Replies: 49
Views: 4705

Re: Backpressure Issue

Nozzles can be defective or clogged with debris. Can you check with the nozzle installed again now? Hello, So I reattached the 0.5mm Nozzle and pushed filament manually through the bowden tube out the nozzle. It requires a good amount of force. As a comparison I replaced the nozzle with a 0.4mm Noz...

Go to advanced search