Search found 10 matches

by ROvermeyer
Wed Jul 11, 2018 11:30 am
Forum: Rostock MAX v3
Topic: 5" touch screen for upgraded V3 machine
Replies: 6
Views: 501

Re: 5" touch screen for upgraded V3 machine

PengLord,

Thanks, looks good. Where did you buy the $6 cable?
by ROvermeyer
Tue Jul 10, 2018 1:15 pm
Forum: Rostock MAX v3
Topic: 5" touch screen for upgraded V3 machine
Replies: 6
Views: 501

Re: 5" touch screen for upgraded V3 machine

Geneb, Thanks for your reply. If SeeMeCNC was not coming out with a kit, drilling holes was one of my options. The other option I was thinking of was to modify the Rev B Frame mounting post, remove the ears, add a threaded section to go through either the webcam or second extruder hole and make a ma...
by ROvermeyer
Mon Jul 09, 2018 3:14 pm
Forum: Rostock MAX v3
Topic: 5" touch screen for upgraded V3 machine
Replies: 6
Views: 501

5" touch screen for upgraded V3 machine

Will there be offered a 5 inch Touch Screen Controller Kit offered for the Max V3 machines that have been upgraded to V3.2?

Thanks.

Bob O.
by ROvermeyer
Sun Jan 21, 2018 6:45 pm
Forum: Rostock MAX v3
Topic: Fan Solutions for 713Maker Effector Plate
Replies: 6
Views: 854

Re: Fan Solutions for 713Maker Effector Plate

I use one of these on my E3d and 713 and it works with auto calabration.

https://www.thingiverse.com/thing:1156005
by ROvermeyer
Fri May 26, 2017 5:38 pm
Forum: KISSlicer
Topic: I wrote a preprocessor that adds coasting support to KS.
Replies: 23
Views: 3254

Re: I wrote a preprocessor that adds coasting support to KS.

626Pilot, I wanted to try you program so I downloaded PHP7 and your program. When I ran you program I get the following error: Fatal error: Uncaught Error: Call to undefined function split() After looking at your program (I don’t know PHP) I checked the PHP manual for the split function and found th...
by ROvermeyer
Fri Mar 10, 2017 11:31 pm
Forum: Rostock MAX v3
Topic: Bed leveling and calibration. Very frustrated.
Replies: 12
Views: 1872

Re: Bed leveling and calibration. Very frustrated.

Don't feel alone, you're not the only one with this problem.
by ROvermeyer
Sun Feb 26, 2017 6:04 pm
Forum: Rostock MAX v3
Topic: How to Upload Firmware HEX to Max v3
Replies: 11
Views: 1621

Re: How to Upload Firmware HEX to Max v3

Brian, I installed Pixel on the Pi using his procedure: https://www.raspberrypi.org/forums/viewtopic.php?f=66&t=133691 Then I installed XRDP using this procedure: http://elinux.org/RPi_XRDP_Server Now you can use Remote Desktop from a windows machine and run the Arduino IDE GUI to install firmwa...
by ROvermeyer
Fri Feb 03, 2017 12:50 pm
Forum: Rostock MAX v3
Topic: Proper Calibrating procedures in different setups
Replies: 10
Views: 1350

Re: Proper Calibrating procedures in different setups

Which calibration method is best to use??

There is the Calibration Wizard for MC https://www.seemecnc.com/pages/delta-calibration-wizard and there is the Delta Calibration plugin for Octoprint. Are they both the same? Is one better then the other?
by ROvermeyer
Mon Dec 26, 2016 12:24 pm
Forum: Rostock MAX v3
Topic: Octoprint
Replies: 6
Views: 749

Re: Octoprint

Would it be simpler just to use a standard Raspberry Pi power supply which cost between $7 and $10?

Go to advanced search