Search found 170 matches

by bplemmons
Tue Dec 24, 2013 2:38 pm
Forum: Rostock MAX
Topic: Print head hits bed in some prints
Replies: 6
Views: 1176

Re: Print head hits bed in some prints

Turns out that my bed size settings were set over what the firmware could handle even though the part would fit on the plate, Your link the the thread help me figure that out, Thanks
Eaglezsore!!

Bill
by bplemmons
Sat Dec 21, 2013 7:38 pm
Forum: Rostock MAX
Topic: Print head hits bed in some prints
Replies: 6
Views: 1176

Re: Print head hits bed in some prints

I'm having a very similar issue myself, net fab shown no errors and the part prints fine at half scale but when I print it full size the head will crash the bed after the first couple of layers... my log shows several errors that reads invalid delta coordinate move ignored.... Baffled Here are some ...
by bplemmons
Thu Oct 17, 2013 1:35 am
Forum: Troubleshooting
Topic: Hot end temp drops after starting of print
Replies: 5
Views: 1272

Re: Hot end temp drops after starting of print

I switched the resistor on the hot end to a cartridge, not only did it fix the problem but it heats a little faster...

Odd thing is my Kossel heats up 3 times as fast with a 7 dollar monitor power supply (not using heated bed on max)
by bplemmons
Tue Oct 15, 2013 1:36 pm
Forum: Troubleshooting
Topic: Hot end temp drops after starting of print
Replies: 5
Views: 1272

Re: Hot end temp drops after starting of print

I check the wiring, I do have inline connectors and I replaced a suspect one, but issue still remains, Doesn't to that from SD card or pronterface..
under the printer setting and connection, that do you have for reset on connect?

You ever try the magnets?

Bill
by bplemmons
Sun Oct 13, 2013 8:43 pm
Forum: Troubleshooting
Topic: Hot end temp drops after starting of print
Replies: 5
Views: 1272

Hot end temp drops after starting of print

All of the sudden, as soon as I try to run a job, the temperature drops very rapidly, (preheat is fine) nothing unusual in my start codes, reran pid....

I'm stumped...

Bill
by bplemmons
Sat Sep 28, 2013 5:01 pm
Forum: Rostock MAX
Topic: Temperature always 1 deg. short of target
Replies: 2
Views: 481

Re: Temperature always 1 deg. short of target

That did it.

you da man!!

Thanks!!!

Bill
by bplemmons
Sat Sep 28, 2013 4:46 pm
Forum: Rostock MAX
Topic: Temperature always 1 deg. short of target
Replies: 2
Views: 481

Temperature always 1 deg. short of target

I have a makerfarm hot end and no matter what temp I set it too, the hot end comes up about 1-2 deg. short, keeping the printer from starting the print. I have ran the pid tune several times and even though the exact thermistor isn't shown on the tables I have tried the common ones.. Isn't there a d...
by bplemmons
Sun Jul 07, 2013 12:17 am
Forum: Rostock MAX
Topic: J head style ptfe liner source?
Replies: 1
Views: 637

J head style ptfe liner source?

I have a Chinese j head and need a ptfe liner that is 3mm od and 1.75mm id with a pointed end. has anyone found a source for them?
by bplemmons
Wed Jun 26, 2013 2:10 am
Forum: Rostock MAX
Topic: Ez extruder slipping
Replies: 13
Views: 2925

Re: Ez extruder slipping

So I could add the line to my start gcode file? I would do it through ardrino but I can find my current repetier firmware file....Unless there is a way to pull it back out of the machine...... ?
by bplemmons
Tue Jun 25, 2013 10:14 pm
Forum: Rostock MAX
Topic: Ez extruder slipping
Replies: 13
Views: 2925

Re: Ez extruder slipping

I think I found the problem. I switched to a different hot end and it still had some kaptan tape on the peek, which must have been blocking some of the air from the peek fan causing clogging which in turn caused extruder issues..
by bplemmons
Mon Jun 24, 2013 10:44 pm
Forum: Rostock MAX
Topic: Ez extruder slipping
Replies: 13
Views: 2925

Re: Ez extruder slipping

Ive been using cura, problems seems to go away with kiss. I even tried the simple mode. My steps are set at 96 for the ez. I'm printing out a version of the Kossel extruder to be used with a geared reduction stepper. similar to xnoion's Anyone else using the new Cura? other than this issue, I really...
by bplemmons
Mon Jun 24, 2013 6:56 pm
Forum: Rostock MAX
Topic: Ez extruder slipping
Replies: 13
Views: 2925

Ez extruder slipping

Anyone else having trouble with the EZ slipping on them?
by bplemmons
Sun Jun 16, 2013 11:29 pm
Forum: Rostock MAX
Topic: bed now reads 180 / 0
Replies: 3
Views: 676

Re: bed now reads 180 / 0

found the issue, plastic connector on bed thermister was bad
by bplemmons
Thu Jun 13, 2013 12:25 am
Forum: Rostock MAX
Topic: link to seeme firmware?
Replies: 7
Views: 1555

Re: link to seeme firmware?

I mean john and Polly both have repeater firmware. I know john has a Marlin version and now a Rep. That is very similar To pollygons.
by bplemmons
Wed Jun 12, 2013 3:58 am
Forum: Rostock MAX
Topic: bed now reads 180 / 0
Replies: 3
Views: 676

bed now reads 180 / 0

I had some excess solder on my onyx that wasn't allowing the glass to lay flat, I used a solder wick on the thermister solder point to remover the excess, now I have this problem.. Did I fry the thermistor?
by bplemmons
Tue Jun 11, 2013 8:59 pm
Forum: Rostock MAX
Topic: link to seeme firmware?
Replies: 7
Views: 1555

Re: link to seeme firmware?

has anyone used both versions? pollygone's and johns? I've read that polys is a little better..smoother?
by bplemmons
Tue Jun 11, 2013 6:05 pm
Forum: Rostock MAX
Topic: link to seeme firmware?
Replies: 7
Views: 1555

link to seeme firmware?

where is the link to the latest seeme repetier firmware?
by bplemmons
Tue Jun 11, 2013 12:43 am
Forum: Rostock MAX
Topic: tricklaser arms printing over sized?
Replies: 7
Views: 1542

Re: tricklaser arms printing over sized?

Check your email..... My bad,sorry. Still want it
by bplemmons
Mon Jun 10, 2013 2:29 am
Forum: Rostock MAX
Topic: tricklaser arms printing over sized?
Replies: 7
Views: 1542

Re: tricklaser arms printing over sized?

It is a different machine...

I haven't seen the heat shield yet, when did you send it Cambo?
by bplemmons
Sun Jun 09, 2013 8:08 pm
Forum: Rostock MAX
Topic: tricklaser arms printing over sized?
Replies: 7
Views: 1542

tricklaser arms printing over sized?

I'm printing the 25 mm cube oversize with new trick laser arms. it is a new machine and I do have the pulleys set to 20 (plastic)
Do I need to change delta radius in the firmware like I did on the magnets?
by bplemmons
Mon Jun 03, 2013 11:20 pm
Forum: Rostock MAX
Topic: steps for ex struder
Replies: 17
Views: 3795

Re: steps for ex struder

just found it... 92.65
by bplemmons
Mon Jun 03, 2013 11:03 pm
Forum: Rostock MAX
Topic: steps for ex struder
Replies: 17
Views: 3795

steps for ex struder

Do I need to change the steps for the new ez struder from the steve one?
by bplemmons
Fri May 31, 2013 3:44 am
Forum: Rostock MAX
Topic: Xnaron Printable Magnetic u-joint option for Rostock Max
Replies: 474
Views: 168079

Re: Xnaron Printable Magnetic u-joint option for Rostock Max

I have issues with the mag arms coming off on very large prints, has anyone else had this issue?

Bill
by bplemmons
Sun May 26, 2013 2:45 pm
Forum: What are YOU making?
Topic: Rostock Max Hollow Calibration Pyramid Challenge!
Replies: 117
Views: 35640

Re: Rostock Max Hollow Calibration Pyramid Challenge!

My Pyramid I just printed today..

kiss 180c
Bill

Go to advanced search