Search found 443 matches

by dc42
Sat Sep 14, 2019 5:58 pm
Forum: KISSlicer
Topic: V4 / Duet2 / KISSlicer / DUAL EXTRUSION Y-bowden FEED and RETRACT?
Replies: 2
Views: 749

Re: V4 / Duet2 / KISSlicer / DUAL EXTRUSION Y-bowden FEED and RETRACT?

You can do the retract/load either in the slicer tool change scripts, or in the Duet tool change files. If you do it in the Duet tool change files, it should work for all slicers.
by dc42
Sat Sep 14, 2019 5:55 pm
Forum: Troubleshooting
Topic: Display Upgrade (issue) - Firmware Upgraded - (Resolved)
Replies: 3
Views: 159

Re: Display Upgrade

See https://miscsolutions.wordpress.com/paneldue/. However, I suspect the load/unload commands are just macros, so I suggest you first compare the contents of the /macros folder on the SD card of your V3.2 with the same folder on your V4.
by dc42
Fri Sep 13, 2019 11:56 am
Forum: Rostock MAX v4
Topic: Ghosting on vertical surfaces
Replies: 13
Views: 522

Re: Ghosting on vertical surfaces

Dynamic Acceleration Adjustment can help with ringing (the cause of ghosting) on some machines. See https://duet3d.dozuki.com/Wiki/Gcode#Section_M593_Configure_Dynamic_Acceleration_Adjustment. There are also some threads about it on the Duet3D forum. But it's better to reduce ringing by mechanical m...
by dc42
Fri Sep 13, 2019 11:51 am
Forum: Artemis
Topic: sudden under-voltage barrage.
Replies: 4
Views: 640

Re: sudden under-voltage barrage.

I don't know what PSUs SeeMeCNC supplies with the Artemis, but it it has a 115V/230V selector switch and your mains is 115V, check that the switch isn't set to 230V.
by dc42
Fri Sep 13, 2019 11:49 am
Forum: Other Machines
Topic: Free Leapfrog CreatrHS - What should I do with it?
Replies: 4
Views: 749

Re: Free Leapfrog CreatrHS - What should I do with it?

A Duet could power that Z motor directly.
by dc42
Fri Sep 13, 2019 3:23 am
Forum: Duet
Topic: Duet 3 now shipping
Replies: 0
Views: 327

Duet 3 now shipping

In case you missed it, we've started shipping Duet 3 main boards. The Duet 3 MB6HC has: Six high current stepper motor drivers, good to about 6A peak/4A RMS One high current output (intended for bed heater) and three medium current outputs (intended for hot end heaters) Three 4-wire can outputs and ...
by dc42
Mon Jul 08, 2019 3:12 pm
Forum: Troubleshooting
Topic: Max v2 issue with peaks and valleys in bed map[NEW DATA]
Replies: 33
Views: 1439

Re: Max v2 issue with peaks and valleys in bed map

Try moving to X0 Y0, then to X100 Y0, then measure the Z probe trigger height a few times. Then move to X<max> Y0, then X100 Y0, and re-measure the trigger height. That will show up the backlash.
by dc42
Tue Jul 02, 2019 8:36 am
Forum: Troubleshooting
Topic: Max v2 issue with peaks and valleys in bed map[NEW DATA]
Replies: 33
Views: 1439

Re: Max v2 issue with peaks and valleys in bed map

Ridges along the X axis that turn into valleys at the other end is a classic sign of backlash in the mechanics. They appear because RRF probes along the X axis in opposite directions in alternate passes. With backlash, the exact nozzle height at a particular point depends on the direction in which y...
by dc42
Tue Jun 25, 2019 4:18 pm
Forum: Troubleshooting
Topic: Best upgrade investment?
Replies: 10
Views: 808

Re: Best upgrade investment?

I use a 330mm diameter x 5mm thick aluminium bed plate with a 300mm diameter AC mains heater on my delta, and that works well. So a 280mm diameter heater should work for you, as long as the bed plate is thick enough to spread the heat well. My delta uses a 24V 5A PSU. With the bed heater being AC ma...
by dc42
Wed May 22, 2019 2:13 am
Forum: Rostock MAX v3.2
Topic: V3 to 3.2 : DUET v. SMCNC connectors?
Replies: 2
Views: 705

Re: V3 to 3.2 : DUET v. SMCNC connectors?

SMCNC sold out on DUETs so I shopped elsewhere. DUET connectors are warned against in V3.2 assembly walkthrough: When inserting the wires in the white Molex KK connectors, make sure you're using the connectors we sent you in the kit, NOT the ones included in the Duet box! I'm guessing this is becau...
by dc42
Fri May 10, 2019 3:51 pm
Forum: Rostock MAX v3
Topic: V3 conversion to WASP LDM Clay extruder process
Replies: 11
Views: 1358

Re: V3 conversion to WASP LDM Clay extruder process

DUET WiFi option: I use my cell phone to hotspot for WiFi; that's how I'm typing now, and I'll be on our closed WiFi-LAN in our shop where I get full (cell)bars through concrete. Somewhere in the gazillion forum posts on the DUET WiFi board I recall reading that the WiFi was unstable? Is this true,...
by dc42
Fri May 10, 2019 3:48 pm
Forum: Rostock MAX v3
Topic: V3 conversion to WASP LDM Clay extruder process
Replies: 11
Views: 1358

Re: V3 conversion to WASP LDM Clay extruder process

If you go with the Duet, you'll end up with a much better printer. That being said, I have no idea how you'd integrate a BL Touch with a Duet controller. Using BLTouch with Duet is covered in the wiki at https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_BLTouch. However, on a delta I advi...
by dc42
Fri Apr 12, 2019 2:53 am
Forum: Troubleshooting
Topic: WiFi dropout - how to reconnect?
Replies: 16
Views: 867

Re: WiFi dropout - how to reconnect?

Duet Web Control displays the version numbers on the Settings page. You can also get the main firmware version using M115 and the WiFi firmware version from the M122 diagnostic report.
by dc42
Thu Apr 11, 2019 5:50 pm
Forum: Troubleshooting
Topic: WiFi dropout - how to reconnect?
Replies: 16
Views: 867

Re: WiFi dropout - how to reconnect?

Which main and WiFi firmwares are you running? 2.02 main and 1.23 WiFi are recommended. Main firmware 2.02 retries automatically if the WiFi connection is lost.
by dc42
Sun Apr 07, 2019 12:54 pm
Forum: Troubleshooting
Topic: Quickie: V4 how to keep the live Z adjustment all the time?
Replies: 5
Views: 525

Re: Quickie: V4 how to keep the live Z adjustment all the time?

The other way to change the Z=0 height is to alter the Z parameter (trigger height) in the G31 command in config.g The advantage of doing it this way is that it will be unaffected by running auto calibration. Increasing the Z parameter (or if it is negative - as with nozzle-contact probes - making i...
by dc42
Thu Apr 04, 2019 3:16 am
Forum: Troubleshooting
Topic: [Solved] V4 touchscreen not doing anything
Replies: 2
Views: 283

Re: V4 touchscreen not doing anything

I am assuming that the touch screen on the V4 is a standard PanelDue. Is the status at the top right of the screen "Connecting"? If so then its failing to establish a connection to the Duet. Common causes are: - Mismatched band rates. Both should be set to 57600. On the touch screen it is selected o...
by dc42
Mon Mar 25, 2019 3:10 am
Forum: Rostock MAX v2
Topic: [SOLVED] Frustrated! Issues with vertical dimensional accuracy and layer shifting on first 5mm of layers
Replies: 4
Views: 584

Re: Frustrated! Issues with vertical dimensional accuracy and layer shifting on first 5mm of layers

A long shot, but are you using steel cored belts? The steel cores fracture, which causes this type of problem.
by dc42
Tue Mar 19, 2019 3:45 am
Forum: Rostock MAX v3.2
Topic: Sampling Filament Compression Force
Replies: 6
Views: 1951

Re: Sampling Filament Compression Force

I don't think any work would need to be done in Cura. If you can come up with a suitable sensor, I'm sure we can support it in Duet 3, and maybe in Duet 2 also. Btw we already have a design for a load cell amplifier interface to the Duet.
by dc42
Tue Mar 12, 2019 6:03 pm
Forum: Rostock MAX v3.2
Topic: Sampling Filament Compression Force
Replies: 6
Views: 1951

Re: Sampling Filament Compression Force

What you need is a load cell or similar sensor that measures the force that is stopping the Bowden tube popping out of the collets at each end. The strain gauge built into the HE300 isn't suitable because, like the the Duet3D Smart Effector is is based on, it is designed to detect changes in force r...
by dc42
Mon Feb 11, 2019 2:56 am
Forum: Rostock MAX v2
Topic: V2 (mid 2016) to V3.2 (current) upgrade?
Replies: 32
Views: 4728

Re: V2 (mid 2016) to V3.2 (current) upgrade?

Don't type in Run, that's part of the instruction to you. The command to type in starts with 'ls'.
by dc42
Tue Jan 15, 2019 2:42 pm
Forum: Troubleshooting
Topic: Max v.3.2 dimensions off in one direction
Replies: 2
Views: 361

Re: Max v.3.2 dimensions off in one direction

If the scaling error is linear then you can use the M579 command in config.g to correct it, see https://duet3d.dozuki.com/Wiki/GCode#Se ... esian_axes. However, scaling errors are often caused by factors that don't cause uniform scaling; so I suggest you try larger test cubes too.
by dc42
Wed Dec 05, 2018 4:19 pm
Forum: Rostock MAX v3.2
Topic: V3 to V3.2 - Stepper Motors?
Replies: 6
Views: 1189

Re: V3 to V3.2 - Stepper Motors?

I covered the benefits of 0.9deg motors including before and after prints in my blog at https://miscsolutions.wordpress.com/201 ... a-printer/. This was on my own Kossel derivative, not on a SeeMeCNC printer, so your mileage may vary.
by dc42
Wed Dec 05, 2018 4:08 pm
Forum: Troubleshooting
Topic: RESOLVED: Z probe issues after recalibration
Replies: 11
Views: 1432

Re: RESOLVED: Z probe issues after recalibration

I am having the same issue. Had to replace duet board when it failed. Afterwards, the printer prints large and then trying to calibrate it has made it do all sorts of goofy things, including ramming against the Y and X pillars. Also the center seems offset. That's almost certainly due to incorrect ...
by dc42
Sun Nov 25, 2018 4:49 pm
Forum: Rostock MAX v3.2
Topic: V3.2 Carbon Fiber Rod upgrade
Replies: 9
Views: 1947

Re: V3.2 Carbon Fiber Rod upgrade

As well as deleting config-override.g, increase the dive height (H parameter in the M558 command) to e.g. 30 until you have it calibrated. That allows more tolerance for the homed height and delta radius not being set accurately. Changing the rod length will have changed the homed height.

Go to advanced search