Search found 47 matches

by dmo
Mon Dec 11, 2017 5:06 pm
Forum: Rostock MAX v3
Topic: Duet HE280 Probe i2c interface
Replies: 44
Views: 4164

Re: Duet HE280 Probe i2c interface

... The Z probe box turns red and shows a value of 1000, I'm guessing that means it's triggered. I am using 1.17e. I still haven't figured out the thermistor wire for sure. I think it goes to the positive lead from reading the SeeMeCnc instructions but it's vague.I'm thinking I should install the R...
by dmo
Mon Dec 04, 2017 7:29 pm
Forum: The Lounge
Topic: Artemis(✓) or Rostock MAX v4 (X)
Replies: 20
Views: 1767

Re: Artemis or Rostock MAX v4

So all of the printing specs seem the same on both except for the build height. How much print quality difference will there be? I'm leaning towards the Artemis because of the new rails but it seems like a steep price difference. I just had to jump in on this one. How much print quality difference ...
by dmo
Sun Nov 26, 2017 11:17 am
Forum: The Lounge
Topic: Artemis(✓) or Rostock MAX v4 (X)
Replies: 20
Views: 1767

Re: Artemis or Rostock MAX v4

So all of the printing specs seem the same on both except for the build height. How much print quality difference will there be? I'm leaning towards the Artemis because of the new rails but it seems like a steep price difference.
by dmo
Fri Mar 24, 2017 1:23 pm
Forum: Rostock MAX v3
Topic: Hot end goes to the bottom and stops.
Replies: 1
Views: 218

Re: Hot end goes to the bottom and stops.

Problem fixed. Turns out it's a Matter Control issue. I imported a gcode from a different slicer and it works perfect. It's been a while since I've used Matter Control and the RAMBO board so I probably just have a setting off.
by dmo
Thu Mar 23, 2017 11:44 pm
Forum: Rostock MAX v3
Topic: Hot end goes to the bottom and stops.
Replies: 1
Views: 218

Hot end goes to the bottom and stops.

I'm not sure if this is a HE280 issue or MC. Everything moves and calorbrates perfectly. I even used the calorbration wizard gcode. When I go to print the calorbration cube the HE goes to the bottom at the X tower, moves a bit and stops. After a while a red light starts flashing on the HE. I'm actua...
by dmo
Sun Mar 19, 2017 9:25 pm
Forum: Rostock MAX v3
Topic: Duet HE280 Probe i2c interface
Replies: 44
Views: 4164

Re: Duet HE280 Probe i2c interface

I'm using a Duet 8.5. I've been having the worst time with yours and mHackney's. I've double checked the wiring, looked for shorts, bad connections everything is right except for one thing I just noticed.You have the the thermistor going to the vin on the board and not the E1r(th). Everything on th...
by dmo
Sun Mar 19, 2017 9:17 pm
Forum: Rostock MAX v3
Topic: Duet HE280 Probe i2c interface
Replies: 44
Views: 4164

Re: Duet HE280 Probe i2c interface

I have no idea what you just wrote but I want it. so what you are saying is that I can use that with the Accel board and a E3D hotend on my MetalMax with a Duet WiFi board. Could you dumb down the post so I can do it? EDIT: Changed to use the Z-probe connections on the Duet and updated code & w...
by dmo
Fri Mar 10, 2017 2:46 pm
Forum: Rostock MAX v3
Topic: Duet HE280 Probe i2c interface
Replies: 44
Views: 4164

Re: Duet HE280 Probe i2c interface

I'm using a Duet 8.5. I've been having the worst time with yours and mHackney's. I've double checked the wiring, looked for shorts, bad connections everything is right except for one thing I just noticed.You have the the thermistor going to the vin on the board and not the E1r(th). Everything on the...
by dmo
Sun Feb 26, 2017 11:02 am
Forum: Rostock MAX v3
Topic: Duet HE280 Probe i2c interface
Replies: 44
Views: 4164

Re: Duet HE280 Probe i2c interface

Have you considered connecting the Teensy to the 4 pin Z probe connector instead of to the E0 endstop connector? You could use the Mod pin on the Z probe connector to do the reset. Selecting probe type 3 in the M558 command will drive that signal low, then select type 5 before you probe to drive it...
by dmo
Fri Aug 05, 2016 3:44 pm
Forum: Duet
Topic: EzStruder Over Heating With Duet
Replies: 4
Views: 571

Re: EzStruder Over Heating With Duet

If the extruder motors are rated at 1.5A then I suggest you set the current to about 1.3A to that they run cooler. You can put a command to turn the unused extruder motor off in the tfree#.g tool change file, where # is the tool number. I don't recommend using I0 in the M906 command unless you real...
by dmo
Fri Jul 29, 2016 6:03 pm
Forum: Duet
Topic: EzStruder Over Heating With Duet
Replies: 4
Views: 571

Re: EzStruder Over Heating With Duet

1. What is the rated current of the stepper motor? Is there a part number label on the motor that would help you to look it up? Try turning the current down to 80% of the rated current. 2. You can use M18 to turn motors off selectively, see http://reprap.org/wiki/Gcodes#M18:_Disable_all_stepper_mot...
by dmo
Fri Jul 29, 2016 5:15 pm
Forum: Duet
Topic: Duet setup - instructions in progress
Replies: 346
Views: 27972

Re: Duet setup - instructions in progress

dc42 wrote:I am out of ideas. I think it's time for you to request a replacement board from your supplier.

Just want to follow up. Everyone was great at getting me a new board. Everything works perfect with the new one. Had it hooked up and running in 30 minutes. The IR probe also works great.
by dmo
Fri Jul 29, 2016 5:08 pm
Forum: Duet
Topic: EzStruder Over Heating With Duet
Replies: 4
Views: 571

EzStruder Over Heating With Duet

I'm trying to figure out why my extruders are over heating with the Duet board. I've been following other's for the motor current of 1500. I'm not sure what the current should be for a stock EZstruder. If I lower the current will I need to adjust other setting to compensate? Also I've been trying to...
by dmo
Sun Jul 10, 2016 11:16 pm
Forum: Duet
Topic: Duet setup - instructions in progress
Replies: 346
Views: 27972

Re: Duet setup - instructions in progress

dc42 wrote:I am out of ideas. I think it's time for you to request a replacement board from your supplier.

Thank you for all of your help on this. I'll send another message to Filistruder. I think he copied you on the last one. The Wfi board sounds pretty exciting.
by dmo
Sat Jul 09, 2016 6:22 pm
Forum: Duet
Topic: Duet setup - instructions in progress
Replies: 346
Views: 27972

Re: Duet setup - instructions in progress

dc42 wrote:So the motor is open circuit then? No wonder it doesn't move.

Oh, the motor, I was testing the pins on the board. The motors have continuity on 1&2, 3&4, the pins on the Duet board does not.
by dmo
Sat Jul 09, 2016 5:16 pm
Forum: Duet
Topic: Duet setup - instructions in progress
Replies: 346
Views: 27972

Re: Duet setup - instructions in progress

Still nothing. I checked the pins and there's no continuity between the pairs. Please explain. Do you mean that you DO get continuity within each pair (between pins 1&2, and between pins 3&4)? Or no continuity anywhere? No continuity. I checked the other pairs as well and there is no contin...
by dmo
Sat Jul 09, 2016 4:58 pm
Forum: Duet
Topic: Duet setup - instructions in progress
Replies: 346
Views: 27972

Re: Duet setup - instructions in progress

PS - I couldn't think of an electrical fault with the board that would affect all the motors - but it has just occurred to me that there IS a fault that would affect the first 4 motors. So please try this: 1. With power off, connect a stepper motor to the E1 (second extruder) connector. This could ...
by dmo
Sat Jul 09, 2016 1:58 pm
Forum: Duet
Topic: Duet setup - instructions in progress
Replies: 346
Views: 27972

Re: Duet setup - instructions in progress

PS - I couldn't think of an electrical fault with the board that would affect all the motors - but it has just occurred to me that there IS a fault that would affect the first 4 motors. So please try this: 1. With power off, connect a stepper motor to the E1 (second extruder) connector. This could ...
by dmo
Sat Jul 09, 2016 9:54 am
Forum: Duet
Topic: Duet setup - instructions in progress
Replies: 346
Views: 27972

Re: Duet setup - instructions in progress

What the G91 should do is avoid the "Attempt to move the motors of a delta printer to absolute positions" message when you send the G1 S2 X10 command. If you are not getting that message and the X motor still isn't moving and the currents are set nonzero, then it does sound like a motor w...
by dmo
Fri Jul 08, 2016 8:52 am
Forum: Duet
Topic: Duet setup - instructions in progress
Replies: 346
Views: 27972

Re: Duet setup - instructions in progress

Have you unplugged a motor with the board powered up? I don't know if it's the same on the Duet, but it's my understanding (at least with the Rambo) that the driver chips don't survive that. g. No, I always unplug the PSU, and USB before doing anything on the board. I'm very careful in the way I ha...
by dmo
Fri Jul 08, 2016 8:22 am
Forum: Duet
Topic: Duet setup - instructions in progress
Replies: 346
Views: 27972

Re: Duet setup - instructions in progress

What the G91 should do is avoid the "Attempt to move the motors of a delta printer to absolute positions" message when you send the G1 S2 X10 command. If you are not getting that message and the X motor still isn't moving and the currents are set nonzero, then it does sound like a motor w...
by dmo
Thu Jul 07, 2016 2:40 pm
Forum: Duet
Topic: Duet setup - instructions in progress
Replies: 346
Views: 27972

Re: Duet setup - instructions in progress

Hi dmo. I actually had a similar issue when converting to the Duet. I had to completely rewire (or swap wires) the connection from each motor to the board. I don't remember what the exact combination or appropriate connections are right off the top of my head, but I can check for you when I get bac...
by dmo
Thu Jul 07, 2016 1:35 pm
Forum: Duet
Topic: Duet setup - instructions in progress
Replies: 346
Views: 27972

Re: Duet setup - instructions in progress

Ok, I'm ready to give up. One last thing. How can I check that the stepper drivers aren't shorted? That's the only thing I can think of.
by dmo
Wed Jul 06, 2016 11:50 am
Forum: Duet
Topic: Duet setup - instructions in progress
Replies: 346
Views: 27972

Re: Duet setup - instructions in progress

Thanks for the suggestions. I tried all of those. When I get to the G1 S2 X10 F500 a blue message box appears "Attempt to move the motors of a delta printer to absolute positions" but nothing happens. You must have forgotten to send G91 first. Just remembered what happened when I did the ...
by dmo
Wed Jul 06, 2016 9:46 am
Forum: Duet
Topic: Duet setup - instructions in progress
Replies: 346
Views: 27972

Re: Duet setup - instructions in progress

Thanks for the suggestions. I tried all of those. When I get to the G1 S2 X10 F500 a blue message box appears "Attempt to move the motors of a delta printer to absolute positions" but nothing happens. You must have forgotten to send G91 first. I'm pretty sure I did send it, but I'll try i...

Go to advanced search