Search found 14 matches

by LAGR
Sat May 06, 2017 8:13 pm
Forum: Duet
Topic: Shorted layer fan
Replies: 4
Views: 726

Re: Shorted layer fan

I ended up using flush cutters to cut off the old fets, tinned the pads, and used a wooden toothpick to hold down the fet and tapped the legs one by one to solder them. It worked but I certainly wouldn't recommend it.
by LAGR
Mon May 01, 2017 3:27 pm
Forum: Duet
Topic: Shorted layer fan
Replies: 4
Views: 726

Re: Shorted layer fan

The always on works so I guess it's time to figure out how to desoldered the mosfets.
by LAGR
Thu Apr 27, 2017 3:28 am
Forum: Duet
Topic: Shorted layer fan
Replies: 4
Views: 726

Shorted layer fan

So last night i was finally getting around to wiring up my layer fan and apparently i was working too late because I managed to not notice a short in my wiring. Long story short in the troubleshooting process I connected this shorted fan to all three of my pwm fan control headers. None of my fan hea...
by LAGR
Mon Feb 13, 2017 2:01 pm
Forum: Duet
Topic: RostockMAX V3 to Duet WiFi conversion instructions
Replies: 68
Views: 6154

Re: RostockMAX V3 to Duet WiFi conversion instructions

Thank you for continually saving my ass :P
by LAGR
Mon Feb 13, 2017 11:02 am
Forum: Duet
Topic: RostockMAX V3 to Duet WiFi conversion instructions
Replies: 68
Views: 6154

Re: RostockMAX V3 to Duet WiFi conversion instructions

It might be time to admit that I just burned the $30 and switch to FSRs, I'm so done trying to troubleshoot this. Any chance you did a write up as good as this one for FSRs on a duet?
by LAGR
Mon Feb 13, 2017 8:38 am
Forum: Duet
Topic: RostockMAX V3 to Duet WiFi conversion instructions
Replies: 68
Views: 6154

Re: RostockMAX V3 to Duet WiFi conversion instructions

So I'm also having a few issues and I was wondering if anyone has any ideas. I'm getting the issue where my probe will skip across the bed because it's not triggering consistently. I've tried sensitivity settings between 5 and 70 and messed with the f value (speed on the probe movement if I understa...
by LAGR
Mon Nov 28, 2016 1:34 pm
Forum: Rostock MAX v2
Topic: Complete upgrade - result: Printer does nothing!!! Please help!
Replies: 23
Views: 1792

Re: Complete upgrade - result: Printer does nothing!!! Please help!

I'd like to piggyback on to this, I just installed probe board and i'm getting the same boot loop. I've double checked all my wiring, tried swapping the thermistor leads and double checked my firmware changes and can't find any issues so i'm pretty much out of ideas. This is what my terminal shows i...
by LAGR
Fri Aug 07, 2015 1:14 am
Forum: Rostock MAX v2
Topic: Trying to do first print, prints look blobby and thin
Replies: 7
Views: 780

Re: Trying to do first print, prints look blobby and thin

yeah it definitely was, i've been doing a few prints and they're turning out fine (not great but I also haven't done much calibration so it's entirely my fault). I got kinda scared about bumping the extruder to 240 because of it only being rated to go to 247 so I'll just wait till my prometheus is o...
by LAGR
Tue Aug 04, 2015 1:33 pm
Forum: Rostock MAX v2
Topic: Trying to do first print, prints look blobby and thin
Replies: 7
Views: 780

Re: Trying to do first print, prints look blobby and thin

My local home depot has makerbot abs, I might run over and see if they have any natural filament Edit: home dept only had PLA so I went to a local component electronics store (Vetco if you're in the seattle area go there, they're awesome) and it turned out that my blac ABS just wasnt extruding prope...
by LAGR
Tue Aug 04, 2015 1:32 pm
Forum: Rostock MAX v2
Topic: Trying to do first print, prints look blobby and thin
Replies: 7
Views: 780

Re: Trying to do first print, prints look blobby and thin

Black ABS (from sainsmart)
HOTEND 235
Bed 80
Speeds (whatever the defaults are in matter control I'll be home in like half an hour to check)

I have a Prometheus v2 in the mail because I've been hearing an all metal hotend should be your first upgrade
by LAGR
Tue Aug 04, 2015 1:17 pm
Forum: Rostock MAX v2
Topic: Trying to do first print, prints look blobby and thin
Replies: 7
Views: 780

Re: Trying to do first print, prints look blobby and thin

I've tried lowering the z incrementally down to the point where it was just tracing the shape in the glue and it didn't seem to help, I'll try the adjusting in the firmware
by LAGR
Tue Aug 04, 2015 1:11 pm
Forum: Rostock MAX v2
Topic: Trying to do first print, prints look blobby and thin
Replies: 7
Views: 780

Trying to do first print, prints look blobby and thin

I've been trying to fit the fan shroud but I just cant seem to get a solid first layer. My first layer keeps looking weird and blobby, any ideas?

https://www.dropbox.com/s/yi9n8qbg62ffs ... 4.jpg?dl=0
by LAGR
Mon Aug 03, 2015 2:24 pm
Forum: Rostock MAX v2
Topic: Stuck in a boot loop
Replies: 3
Views: 692

Re: Stuck in a boot loop

I had to flip my lcd "B" cable, thanks for the help :)
by LAGR
Mon Aug 03, 2015 10:18 am
Forum: Rostock MAX v2
Topic: Stuck in a boot loop
Replies: 3
Views: 692

Stuck in a boot loop

Whenever I flash over repetier my printer gets stuck in a weird boot loop. it'll start up then attempt to home the towers then estop and reboot.

Any help is appreciated

https://www.youtube.com/watch?v=GQZlVIxgPlc

Go to advanced search