Search found 17 matches

by jreyes
Tue Nov 22, 2016 8:55 pm
Forum: FAIL HAPPENS ! ! !
Topic: Couple issues of prints
Replies: 3
Views: 1544

Re: Couple issues of prints

Thanks for your the reply's

I will go to each steps and see troubleshoot it and get back to you
by jreyes
Fri Nov 18, 2016 7:11 pm
Forum: FAIL HAPPENS ! ! !
Topic: Couple issues of prints
Replies: 3
Views: 1544

Couple issues of prints

Hasn’t been going well for me for this month. For some reason I can’t get a good print.
The green one is a good print before messing with the hotend. Now it print ok but some prints are coming out really bad. The white one is example.

20161118_180252.jpg

20161118_180241.jpg

20161118_180226.jpg
by jreyes
Wed Nov 09, 2016 10:12 pm
Forum: Troubleshooting
Topic: Issues with J-head V6 Hotend
Replies: 11
Views: 1212

Re: Issues with J-head V6 Hotend

This is with other hotend. It only printed the layer you see and than it stop. I try it with different models stl but does the same. It one of those bad days for me.

20161109_210314.jpg

20161109_210244.jpg
by jreyes
Wed Nov 09, 2016 6:13 pm
Forum: Troubleshooting
Topic: Issues with J-head V6 Hotend
Replies: 11
Views: 1212

Re: Issues with J-head V6 Hotend

At the moment I haven't made no settings to the printer. I try method I found online using Nylon Didn't work I disassemble it and put it jar and added actone for day. It clean inside. I put it back still have issues melting the filament. I remove hotend and install new one hotend. Look like it still...
by jreyes
Mon Nov 07, 2016 6:25 pm
Forum: Troubleshooting
Topic: Issues with J-head V6 Hotend
Replies: 11
Views: 1212

Re: Issues with J-head V6 Hotend

I just got back from work. I will do some cleaning from inside.

Mac The Knife
I set it to 240C but I had the same issue. I did that to see if made a different but no :cry:

Printed on Friday. 225c 20 Infill
good.jpg


Printed on Saturday. 240 20 infill but it weak.
bad.jpg
by jreyes
Mon Nov 07, 2016 11:16 am
Forum: Troubleshooting
Topic: Issues with J-head V6 Hotend
Replies: 11
Views: 1212

Re: Issues with J-head V6 Hotend

Nozzle is set to 225 sorry I made mistake on my post. I will try the cleaning nozzle bore and see if it fix the issue.

Thanks
by jreyes
Mon Nov 07, 2016 9:30 am
Forum: Troubleshooting
Topic: Issues with J-head V6 Hotend
Replies: 11
Views: 1212

Issues with J-head V6 Hotend

Rostock max v2 J-head V6 Hotend 1.75mm Nozzle : 125 Bed: 99 ABS I been printing fine until yesterday I notice it wasn't printing well. I print about 60 hours or more into it and was working great. I clean Nozzle tip, Use thin wire to clean inside of it and check the wire . Seem like it having issue ...
by jreyes
Mon Apr 11, 2016 6:56 pm
Forum: Mods and Upgrades
Topic: BondTech QR Extruder Tip #1 - Calibration
Replies: 52
Views: 15869

Re: BondTech QR Extruder Tip #1 - Calibration

I recheck the wires from Rambo and stepper. How do I invert the stepper direction on E1 This how I wire them http://s18.postimg.org/60lf0znr9/20160411_172324.jpg http://s18.postimg.org/3kjln55ol/20160411_172645.jpg http://s15.postimg.org/bg5fqa913/20160410_161949.jpg http://s23.postimg.org/qju6godqv...
by jreyes
Sun Apr 10, 2016 10:13 pm
Forum: Mods and Upgrades
Topic: BondTech QR Extruder Tip #1 - Calibration
Replies: 52
Views: 15869

Re: BondTech QR Extruder Tip #1 - Calibration

Let me check Wires and I get back to you Xenocrates. May reply late due to night time.

Thank you for your help and assist Xenocrates
by jreyes
Sun Apr 10, 2016 6:26 pm
Forum: Mods and Upgrades
Topic: BondTech QR Extruder Tip #1 - Calibration
Replies: 52
Views: 15869

Re: BondTech QR Extruder Tip #1 - Calibration

Xenocrates wrote:Was it changed through mattercontrol or on the LCD? It seems like the LCD doesn't update properly. just to confirm, the previous entry there was ~95?


I use Repetier Host to make changes and entry was 90.
by jreyes
Sun Apr 10, 2016 5:52 pm
Forum: Mods and Upgrades
Topic: BondTech QR Extruder Tip #1 - Calibration
Replies: 52
Views: 15869

Re: BondTech QR Extruder Tip #1 - Calibration

If you have a Rambo, you don't have a config.g. Open up the EEPROM, and change the E.1 steps/mm parameter. Ok I have the Rambo. I went to EEPROM change the the E.1 steps to 490 to Calibration so on. Send the command G1 E100 F1500. but doesn't feed. Seem like it feeding backwards nor feeding at all.
by jreyes
Sun Apr 10, 2016 10:34 am
Forum: Mods and Upgrades
Topic: BondTech QR Extruder Tip #1 - Calibration
Replies: 52
Views: 15869

Re: Installing the BondTech QR Extruder

Hey mhackney

I have quick question I purchase bondtech and already install it on rostock max v2. On the configuration. Where do you go to look for config.g
Thanks
by jreyes
Mon May 11, 2015 10:30 pm
Forum: FAIL HAPPENS ! ! !
Topic: Issue printing items
Replies: 5
Views: 1326

Re: Issue printing items

Host software using is the MatterControl ABS Hotend 228 Heatbed 80 Using glue stick first but didn’t work dry up fast. Using hair spray on the glass first. Room temp is around 60-70 Just so you know the glue stick glue is supposed to dry up on the bed before it is used. So "Dry up fast" i...
by jreyes
Mon May 11, 2015 5:25 pm
Forum: FAIL HAPPENS ! ! !
Topic: Issue printing items
Replies: 5
Views: 1326

Re: Issue printing items

Host software using is the MatterControl
ABS
Hotend 228
Heatbed 80
Using glue stick first but didn’t work dry up fast. Using hair spray on the glass first.
Room temp is around 60-70
by jreyes
Sun May 10, 2015 6:37 pm
Forum: FAIL HAPPENS ! ! !
Topic: Issue printing items
Replies: 5
Views: 1326

Issue printing items

I been trying to get some good items printing out but having issue. I don't know where to start. I don't wanna go back and do adjustment and mess it up more. Any tips or something I can try. http://ww2.jreyes.us/wp-content/uploads/2015/05/20150510_170158-e1431296833745.jpg http://ww2.jreyes.us/wp-co...
by jreyes
Sat Apr 25, 2015 10:26 pm
Forum: Troubleshooting
Topic: Error on PID Autotune
Replies: 6
Views: 1028

Re: Error on PID Autotune

No just stay in 25.5 on NOZ. I don't see hot end heating up.
by jreyes
Sat Apr 25, 2015 6:55 pm
Forum: Troubleshooting
Topic: Error on PID Autotune
Replies: 6
Views: 1028

Error on PID Autotune

Following the Rostock MAX v2 Assembly Guide. Im in the PID Auto tune” routine. When I type the command M303 S200 it starts the PID Autotune start In about 10-15 mins error say Error: PID Autotune failed! timeout. On the board I see LED2 and LED4 light Red I don't know if means something. I check the...

Go to advanced search