Search found 616 matches

by IMBoring25
Sun Aug 19, 2018 10:59 am
Forum: Troubleshooting
Topic: Not connecting to round circles
Replies: 1
Views: 115

Re: Not connecting to round circles

I see a few places that make it look like you might be having difficulty restarting extrusion after retractions. Which hot end are you using and what are your retraction settings?
by IMBoring25
Mon Jul 09, 2018 11:06 pm
Forum: Troubleshooting
Topic: Duet WiFi - Rostock V2
Replies: 13
Views: 640

Re: Duet WiFi - Rostock V2

1) Not aware of anything but I'm not familiar with your specific PSU. I'm running all Meanwells now. Putting the side covers back on would probably help. 2) See https://reprap.org/wiki/G-code (the g-code reference) for M106 and add the command you come up with for your preferred behavior to your con...
by IMBoring25
Sun Jun 17, 2018 11:07 am
Forum: Troubleshooting
Topic: temperature
Replies: 2
Views: 210

Re: temperature

I melted a PETG dashcam mount and haven't had a problem with its ABS replacement. YMMV.
by IMBoring25
Tue May 08, 2018 10:29 pm
Forum: Troubleshooting
Topic: Messy print
Replies: 7
Views: 431

Re: Messy print

1) He's talking about the accuracy of the first-layer height, not its absolute value in mm. That comment was about the quality of your leveling, not your slicer settings. 2) In case it becomes relevant in the future, typical layer heights are on the order of 0.2 and 0.3 mm. Whole-number mm layer hei...
by IMBoring25
Mon Apr 16, 2018 3:52 pm
Forum: Hacker Series - H2
Topic: Software/hardware parameter limititing print size
Replies: 4
Views: 2124

Re: Software/hardware parameter limititing print size

That doesn't mean it's not a problem with wall thickness or STL quality.
by IMBoring25
Tue Apr 10, 2018 7:50 pm
Forum: Heated Bed How-To's
Topic: Onyx Temp Rating
Replies: 11
Views: 1139

Re: Onyx Temp Rating

I fiddled with polycarbonate a little. Even at a 150 bed in an enclosure around 35 it would only stick for a layer or two before completely peeling up. It may just not like Kapton, but that was my experience.
by IMBoring25
Sun Apr 08, 2018 10:05 pm
Forum: Hacker Series - H2
Topic: Software/hardware parameter limititing print size
Replies: 4
Views: 2124

Re: Software/hardware parameter limititing print size

That doesn't look like the behavior I'd expect from hitting the firmware limit on printable radius. Does the STL get thinner there, potentially thinner than the nozzle? Are you sure the STL is manifold?
by IMBoring25
Mon Mar 19, 2018 10:23 am
Forum: Troubleshooting
Topic: My printer has gotten an attitude.
Replies: 34
Views: 1664

Re: My printer has gotten an attitude.

As long as they're perfectly swapped the only impact should be that you'll need to mirror any asymmetrical parts for them to turn out right.
by IMBoring25
Tue Feb 13, 2018 7:12 pm
Forum: Artemis
Topic: Hot End Chattering/Bouncing Against Bed, Not Much Extruded (Bad config.g?)
Replies: 25
Views: 1583

Re: Hot End Chattering/Bouncing Against Bed, Not Much Extruded (Bad config.g?)

If you can get the first-part cost reasonably low, an accessible technology with little economy of scale to be realized has its own benefits, as there's basically no penalty for making one-off or incremental changes, so each machine can be as unique as desired. The choices of the names Darwin and Me...
by IMBoring25
Sat Jan 20, 2018 9:06 pm
Forum: Artemis
Topic: Big default "baby steps" - Duet
Replies: 3
Views: 431

Re: Big default "baby steps" - Duet

Add M290 with your desired step in mm as an S parameter. http://reprap.org/wiki/G-code I'll let someone who's with autolevel handle (1). Some PID tune their beds. I've been happy with my results without even using PID. An SSR gets the high bed power currents off the circuit board and gives the optio...
by IMBoring25
Sat Jan 20, 2018 9:37 am
Forum: Rostock MAX v3
Topic: Trouble installing an E3D v6
Replies: 6
Views: 716

Re: Trouble installing an E3D v6

Did you change the thermistor settings in the firmware for the nonstandard hot end and retune PID? You may need to change the max PID drive upwards since the standard E3D heater is only 25W. Is the fan turning (and turning the correct way)? Is it a genuine E3D? There are a lot of clones out there an...
by IMBoring25
Fri Dec 29, 2017 7:37 pm
Forum: Rostock MAX v3
Topic: Dead board??
Replies: 1
Views: 321

Re: Dead board??

You can't visually inspect a fuse. They can lose continuity with a break that isn't visible to the naked (or even aided) eye.
by IMBoring25
Sun Dec 24, 2017 5:32 pm
Forum: Rostock MAX v3
Topic: Fan Speed
Replies: 1
Views: 427

Re: Fan Speed

If you're talking about Slic3r, the fan speed settings work with the other cooling settings. Not sure how many of these make it into the MatterControl interface, but they're all there if you download from slic3r.org: The full fan logic for parts of the print that are neither first X layers nor bridg...
by IMBoring25
Mon Dec 11, 2017 7:38 pm
Forum: Troubleshooting
Topic: Poor layer quality on multi-part prints
Replies: 10
Views: 1363

Re: Poor layer quality on multi-part prints

It's the axis steps per mm that shouldn't change from 80. Extruder steps per mm should be determined experimentally during calibration because there are many variables. 80 should not be correct for the extruder, which should be calibrated experimentally. You probably have problems elsewhere that hap...
by IMBoring25
Sun Dec 10, 2017 9:02 pm
Forum: Troubleshooting
Topic: def has started to appear frequently destroying prints
Replies: 17
Views: 1829

Re: def has started to appear frequently destroying prints

Check the heated bed fuse with a multimeter. If that checks bad, replace it. If it checks good, begin standard diagnostics... Voltage at the board, voltage at the bed...
by IMBoring25
Mon Dec 04, 2017 11:02 pm
Forum: Troubleshooting
Topic: Duet WiFi with E3V6 dragging on plate
Replies: 36
Views: 2820

Re: Duet WiFi with E3V6 dragging on plate

Dragging lightly across the build plate sounds perfect if you're at Z=0. Other than the probing, a real print will never command the nozzle closer to the bed than the first-layer height.
by IMBoring25
Mon Nov 27, 2017 7:11 pm
Forum: Troubleshooting
Topic: Layers shifting to the Z tower
Replies: 7
Views: 676

Re: Layers shifting to the Z tower

More likely than X and Y both skipping the same amount is a problem with Z. Which way it shifts will also depend on whether the cheapskate is trying to go up or down when it doesn't.
by IMBoring25
Fri Nov 24, 2017 6:09 pm
Forum: Troubleshooting
Topic: Upgraded E3Dv6 hot end not heating above 247C
Replies: 5
Views: 562

Re: Upgraded E3Dv6 hot end not heating above 247C

To understand the issue, we really need something more specific than "not heating above..."

Is it rejecting the setpoint and failing back to a 247 setpoint? Or is it accepting the setpoint and just not succeeding in reaching it?
by IMBoring25
Sat Nov 18, 2017 11:58 am
Forum: Troubleshooting
Topic: Rostock Doesn't Home After Printing w/ Cura - Pic
Replies: 5
Views: 664

Re: Rostock Doesn't Home After Printing w/ Cura - Pic

Some people use one software to slice and another to interface with the machine, even if one of the software packages supports both, due to compatibility issues, features, or personal preference, so just using Cura doesn't necessarily mean you were using it for everything. I have about 10 minutes us...
by IMBoring25
Sat Nov 18, 2017 1:25 am
Forum: Troubleshooting
Topic: Rostock Doesn't Home After Printing w/ Cura - Pic
Replies: 5
Views: 664

Re: Rostock Doesn't Home After Printing w/ Cura - Pic

G-code flavor is correct if you have the stock electronics.

How are you loading the gcode to the machine? I found the upload function in Repetier Host had a couple of checkboxes for including start and end gcode that I have to clear to keep it from doing goofy things.
by IMBoring25
Mon Nov 13, 2017 1:16 am
Forum: Rostock MAX v2
Topic: Replacing the hotend on my Max V2
Replies: 7
Views: 1064

Re: Replacing the hotend on my Max V2

My recollection is it's .5mm but I don't have the manual in front of me. If the filament has been sitting out all this time it might have absorbed too much moisture. There are various ways to try to dehydrate it. I've not had mine in a controlled environment and the opaque ABS is fine but the transp...
by IMBoring25
Sun Nov 12, 2017 2:24 am
Forum: Troubleshooting
Topic: RostockV2 hot end won't heat past 145C
Replies: 7
Views: 699

Re: RostockV2 hot end won't heat past 145C

It's not a wrong resistor issue. These same resistors were working correctly before. Something has gone wrong.

The hot end in question is the stock v2 hot end. I don't see that you've ever said what machine you have but it would probably be a downgrade.
by IMBoring25
Sat Nov 11, 2017 6:37 pm
Forum: Troubleshooting
Topic: RostockV2 hot end won't heat past 145C
Replies: 7
Views: 699

Re: RostockV2 hot end won't heat past 145C

It does sound like the increased resistance just isn't letting enough current through to overcome the heat loss to the atmosphere and pass 145. I'd check resistance at the resistor leads to rule out a problem with the wiring going down to the board. Check the leads of one resistor and the leads of t...
by IMBoring25
Fri Nov 10, 2017 1:15 am
Forum: Slic3r
Topic: setting up Slic3r for dual extrusion with shared hotend
Replies: 2
Views: 566

Re: setting up Slic3r for dual extrusion with shared hotend

Your question at the RepRap forums is a lot more specific and thus possible to answer. I am still using 1.2.9, but I would expect the dev version hasn't changed in this respect. If you hover over the Start GCode field, one of the notes is (paraphrased) that including M104 commands in your start gcod...
by IMBoring25
Fri Nov 10, 2017 1:03 am
Forum: Troubleshooting
Topic: Is my Rostock Max2 possessed by demons?
Replies: 22
Views: 1495

Re: Is my Rostock Max2 possessed by demons?

Everything that happens after it "suddenly freaks out" is because the effector is no longer where the electronics think it is. Deltas do goofy things when they don't know where in the build volume they are. What slicer are you using? I have read something about Simplify3D making excessive ...

Go to advanced search