Unless you take your glass off or rotate it, there's usually no reason to re-run the map.
g.
Search found 4579 matches
- Wed Apr 18, 2018 7:49 am
- Forum: Troubleshooting
- Topic: Duet WiFi with E3V6 dragging on plate
- Replies: 36
- Views: 1900
- Tue Apr 17, 2018 8:10 am
- Forum: Artemis
- Topic: Enable strain gauge Z probe?
- Replies: 17
- Views: 490
Re: Enable strain gauge Z probe?
Understand that there's a difference between auto-level and auto-calibration. Broadly speaking the terms can be interchangeable, but when you're into the weeds like this, it's important to know which is which. What G32 does is auto-calibration. The series of probes it does allows a solver to ensure ...
- Mon Apr 16, 2018 9:13 am
- Forum: Rostock MAX v3
- Topic: Autoleveling issue
- Replies: 1
- Views: 66
Re: Autoleveling issue
I would check the connector to make sure that the pins are fully seated in the connector shell and that the connector is fully seated on the RAMBo. What you're describing sounds like a wiring issue.
g.
g.
- Mon Apr 16, 2018 9:10 am
- Forum: Troubleshooting
- Topic: Sudden stop during 1st layer, 0 deg -> Killed
- Replies: 24
- Views: 477
Re: Sudden stop during 1st layer, 0 deg -> Killed
Have you tried setting the Z height through the control panel?
g.
g.
- Fri Apr 13, 2018 7:51 am
- Forum: Artemis
- Topic: Heater issues
- Replies: 8
- Views: 134
Re: Heater issues
You do an M303 Heater 1 Temp 210 M303 H1 S210 Followed by an M303 Write the parameters down Then check config.g and config-override.g Under M307 command you should see the parameters you wrote down. (just a tweak to the above) Tack an M501 to the bottom of your config.g file so that it will load co...
- Tue Apr 10, 2018 8:26 am
- Forum: Rostock MAX v2
- Topic: Hot end won't turn off
- Replies: 10
- Views: 361
Re: Hot end won't turn off
D'oh. 
g.

g.
- Tue Apr 10, 2018 8:25 am
- Forum: Artemis
- Topic: ABS recommendations
- Replies: 2
- Views: 103
Re: ABS recommendations
I'll second the AquaNet tip - the heated bed performance is a lot better with the Artemis since the heat spreader gives a much more even heat. Just be aware that the vinyl decal on the heat spreader will darken at higher temps. (Unless you've got one of the black anodized beds, then you don't have a...
- Mon Apr 09, 2018 9:12 am
- Forum: Troubleshooting
- Topic: Duet WiFi with E3V6 dragging on plate
- Replies: 36
- Views: 1900
Re: Duet WiFi with E3V6 dragging on plate
Again, M500 doesn't have anything to do with calibration. All it does is output any differences between config.g and the in-ram configuration out to a file called config-override.g. This entry lists what exactly is stored when M500 is executed: https://duet3d.dozuki.com/Wiki/Gcode#Section_M500_Store...
- Mon Apr 09, 2018 8:56 am
- Forum: Rostock MAX v2
- Topic: Hot end won't turn off
- Replies: 10
- Views: 361
Re: Hot end won't turn off
You could also buy the SE300 heater block. That takes the new cartridge thermistor and is a drop-in replacement for the older style HE280 heater block.
g.
g.
- Mon Apr 09, 2018 8:45 am
- Forum: Rostock MAX v2
- Topic: Replace nozzle "old" style
- Replies: 7
- Views: 406
Re: Replace nozzle "old" style
TIL!
BTW, are you familiar with the adventures of Luke Vaxhacker and Dec Vadic?
g. (former owner of a VAX 8250)
BTW, are you familiar with the adventures of Luke Vaxhacker and Dec Vadic?

g. (former owner of a VAX 8250)
- Sun Apr 08, 2018 11:07 am
- Forum: Artemis
- Topic: T-Slot Roll in for 10 Series 1/4 w 4mm or 5mm
- Replies: 8
- Views: 217
Re: T-Slot Roll in for 10 Series 1/4 w 4mm or 5mm
I don't know the answer to the RAMBo question, sorry.
The crimpers (PA-09 AND -21) will end up in a drawer with the other dozen+ normal & aerospace crimp tools I have.
g.
The crimpers (PA-09 AND -21) will end up in a drawer with the other dozen+ normal & aerospace crimp tools I have.

g.
- Sun Apr 08, 2018 10:40 am
- Forum: Troubleshooting
- Topic: Duet WiFi with E3V6 dragging on plate
- Replies: 36
- Views: 1900
Re: Duet WiFi with E3V6 dragging on plate
M500 doesn't calibrate anything, it just writes changed things to config-override.g.
g.
g.
- Sun Apr 08, 2018 10:33 am
- Forum: Rostock MAX v2
- Topic: Hot end won't turn off
- Replies: 10
- Views: 361
Re: Hot end won't turn off
The thermistor hasn't been discontinued, it's just sold out.
They should have stock on them shortly.
g.
They should have stock on them shortly.
g.
- Fri Apr 06, 2018 9:46 am
- Forum: Artemis
- Topic: T-Slot Roll in for 10 Series 1/4 w 4mm or 5mm
- Replies: 8
- Views: 217
Re: T-Slot Roll in for 10 Series 1/4 w 4mm or 5mm
No image is appearing.
g.
g.
- Thu Apr 05, 2018 8:50 am
- Forum: Artemis
- Topic: Duet Tuning.
- Replies: 14
- Views: 458
Re: Duet Tuning.
Since you just cost me $44 for a new crimping tool *shakes fist*, I'm going to cost you $52 for a very excellent set of magnifiers: https://www.amazon.com/gp/product/B012M3IV80 :D :D :D These have a focal length of around 420mm, which means you're working at arms length, not 2" from your face. ...
- Thu Apr 05, 2018 8:39 am
- Forum: New Member introduction
- Topic: Oldie but Newbie
- Replies: 1
- Views: 77
- Thu Apr 05, 2018 8:36 am
- Forum: Troubleshooting
- Topic: Duet WiFi with E3V6 dragging on plate
- Replies: 36
- Views: 1900
Re: Duet WiFi with E3V6 dragging on plate
I do this myself - my start gcode includes a G32 right after the G28.
g.

g.
- Thu Apr 05, 2018 8:33 am
- Forum: New Member introduction
- Topic: New to 3D printing and need help
- Replies: 7
- Views: 263
Re: New to 3D printing and need help
Those may be the old arms, I'm not sure. I _think_ those arms are measured from hole center to hole center, not end to end.
g.
g.
- Wed Apr 04, 2018 7:59 am
- Forum: Artemis
- Topic: T-Slot Roll in for 10 Series 1/4 w 4mm or 5mm
- Replies: 8
- Views: 217
Re: T-Slot Roll in for 10 Series 1/4 w 4mm or 5mm
Nice! You could throw a heat-set insert into it as well.
g.
g.
- Wed Apr 04, 2018 7:57 am
- Forum: The Lounge
- Topic: Question on tape covered melamine source
- Replies: 4
- Views: 290
Re: Question on tape covered melamine source
They apply the tape before they cut it, it doesn't ship that way. You can buy rolls of masking tape wide enough to cover your material.
g.
g.
- Wed Apr 04, 2018 7:55 am
- Forum: Artemis
- Topic: Duet Tuning.
- Replies: 14
- Views: 458
Re: Duet Tuning.
Holy Overkill, Batman! 
Go here, http://www.hansenhobbies.com/products/c ... in_lp_1x4/ and grab a male 1x4 housing (2nd item down).
They also sell a ratcheting crimp tool that works wonderfully.
g.

Go here, http://www.hansenhobbies.com/products/c ... in_lp_1x4/ and grab a male 1x4 housing (2nd item down).
They also sell a ratcheting crimp tool that works wonderfully.
g.
- Wed Apr 04, 2018 7:47 am
- Forum: New Member introduction
- Topic: New to 3D printing and need help
- Replies: 7
- Views: 263
Re: New to 3D printing and need help
Can you post a photo of the machine? That might help date it.
g.
g.
- Tue Apr 03, 2018 8:37 am
- Forum: Troubleshooting
- Topic: Cura 3.2.1 printer selection for Rostock V3.2
- Replies: 3
- Views: 171
Re: Cura 3.2.1 printer selection for Rostock V3.2
You're welcome!
g.
g.
- Mon Apr 02, 2018 8:58 am
- Forum: Troubleshooting
- Topic: Cura 3.2.1 printer selection for Rostock V3.2
- Replies: 3
- Views: 171
Re: Cura 3.2.1 printer selection for Rostock V3.2
Here's the cure to those ills: https://seemecnc.dozuki.com/Guide/Setti ... 87?lang=en 
FYI, when version Cura 3.3 is released it will include selections for SeeMeCNC's printers.
g.

FYI, when version Cura 3.3 is released it will include selections for SeeMeCNC's printers.
g.
- Mon Apr 02, 2018 8:55 am
- Forum: Troubleshooting
- Topic: Sudden stop during 1st layer, 0 deg -> Killed
- Replies: 24
- Views: 477
Re: Sudden stop during 1st layer, 0 deg -> Killed
Until you figure out the SD card issue, you can print gcode you sliced in the current Cura using MC. You could also use this as excuse to set up OctoPrint and use that to print files uploaded from Cura. 
g.

g.