Search found 4729 matches

by geneb
Fri Dec 14, 2018 9:00 am
Forum: Rostock MAX v2
Topic: Max V2 upgrade to HE280
Replies: 3
Views: 45

Re: Max V2 upgrade to HE280

Here's the HE280 upgrade instructions https://seemecnc.dozuki.com/Guide/Rostock+Max+v1-v2+HE280+Hotend+Upgrade/49?lang=en, these may help you decide what you want to do regarding the whip. Personally, I'd buy the whip because it's a damn sight easier than dealing with getting the shrink tube over th...
by geneb
Fri Dec 14, 2018 8:55 am
Forum: Rostock MAX v3.2
Topic: Rostock MAX v3.2 reviews
Replies: 20
Views: 275

Re: Rostock MAX v3.2 reviews

The PCB-style heater that the v3.2 uses may be able to hit 100C, but I've never personally tried anything higher than 90C. If your bed-heat need is driven by a requirement to print ABS, you should enclose the printer and that will help offset any problems associated with a lower bed temp. An enclosu...
by geneb
Fri Dec 14, 2018 8:50 am
Forum: Rostock MAX
Topic: Anyone else still rocking the original Rostock Max?
Replies: 2
Views: 25

Re: Anyone else still rocking the original Rostock Max?

I actually started the retirement process for Orange Menace on Wednesday. It had been updated to a Hotends.com j-head and a Duet Wifi. That controller is now destined for my v3 to make it a v3.2.

g.
by geneb
Thu Dec 13, 2018 8:40 am
Forum: Troubleshooting
Topic: Orion upgrade questions
Replies: 3
Views: 56

Re: Orion upgrade questions

If memory serves it's around 6.8 ohms as tested at the crimp points where the resistor leads are joined together. If you upgrade to the HE280 hot end, you'll get auto-calibration. The HE280 has a sensor on the board that allows the whole hot end to be used as a Z probe. You can see what that upgrade...
by geneb
Thu Dec 13, 2018 8:34 am
Forum: Rostock MAX v3.2
Topic: Rostock MAX v3.2 reviews
Replies: 20
Views: 275

Re: Rostock MAX v3.2 reviews

The SE300 can hit at least 280C. The Jet liner isn't applicable to the SE300 - that's only needed for the HE280 hot end. The filament path in the SE300 is all metal, unlike the HE280, thus the liner requirement. Note that the HE280 hot end is not used with the Rostock MAX 3.2, it's only in the v3. I...
by geneb
Thu Dec 13, 2018 8:29 am
Forum: Mods and Upgrades
Topic: SE300 Pin Outs & LED Power
Replies: 2
Views: 43

Re: SE300 Pin Outs & LED Power

Email support, I'm sure they can tell you.

g.
by geneb
Tue Dec 11, 2018 8:31 am
Forum: Rostock MAX v3
Topic: Cura 3.6 preloaded Rostock profile
Replies: 3
Views: 67

Re: Cura 3.6 preloaded Rostock profile

I've used the presets in Cura with both my 3.2 and Artemis. You still need to import the SE300 profiles though. :)

g.
by geneb
Tue Dec 11, 2018 8:30 am
Forum: Troubleshooting
Topic: Orion upgrade questions
Replies: 3
Views: 56

Re: Orion upgrade questions

If your Orion uses the older heating resistors (one on each "side" of the round heater block), there's no real gotchas with the firmware. However, if you have an Orion with the HE280 hot end that allows the Orion to auto-calibrate, you need to stick with the SeeMeCNC supplied firmware - th...
by geneb
Mon Dec 10, 2018 9:23 am
Forum: Rostock MAX v3
Topic: Cura 3.6 preloaded Rostock profile
Replies: 3
Views: 67

Re: Cura 3.6 preloaded Rostock profile

You can download the hotend-specific profiles from SeeMeCNC's git repository - there's Cura profiles for both the SE300 and HE280 hot ends. The 3.2 profile should work reasonably well as-is, but you'll need to make sure the travel speeds are under 250mm/sec if you only have a v3. (The RAMBo can't ha...
by geneb
Sun Dec 09, 2018 2:58 pm
Forum: Rostock MAX v3.2
Topic: Rostock MAX v3.2 reviews
Replies: 20
Views: 275

Re: Rostock MAX v3.2 reviews

Naomi is pretty awesome. If it weren't for the basement dwelling incels of the world, she'd be getting the kudos she's earned.

g.
by geneb
Sat Dec 08, 2018 10:10 am
Forum: Rostock MAX v3.2
Topic: Rostock MAX v3.2 reviews
Replies: 20
Views: 275

Re: Rostock MAX v3.2 reviews

SeeMeCNC is a pretty small company with pretty large capabilities. Every injection molded part on one of their printers was built from molds machined on-site and shot on injection molding machines that are also on-site. You're not going to find that in any 3D printer built inside the USA. I would re...
by geneb
Fri Dec 07, 2018 8:16 am
Forum: Troubleshooting
Topic: Layer Shifting
Replies: 38
Views: 662

Re: Layer Shifting

If it's not able to tighten flush, there's something in the way.

g.
by geneb
Thu Dec 06, 2018 8:18 am
Forum: What are YOU making?
Topic: Coming soon from 713Maker.com
Replies: 69
Views: 10249

Re: Coming soon from 713Maker.com

Very nice! If you add some shiny brass accents (screws, etc), you'd have a Valkyrie on your hands. ;)

g.
by geneb
Wed Dec 05, 2018 8:33 am
Forum: Troubleshooting
Topic: Layer Shifting
Replies: 38
Views: 662

Re: Layer Shifting

Is the nozzle lifting before it makes a travel move?

You might also check the wiring of all three steppers to make sure a pin isn't crawling out of the connector shell.
g.
by geneb
Wed Dec 05, 2018 8:31 am
Forum: Rostock MAX v3.2
Topic: Rostock MAX v3.2 reviews
Replies: 20
Views: 275

Re: Rostock MAX v3.2 reviews

I have Rostock MAX models going back to 2013 and none have failed due to a mechanical issue, with the exception of the pre-ball joint arms. (The u-joints would sometimes gall the stainless steel axles and begin to bind.) The ball & socket arms have eliminated that issue. The cycle of tweaking an...
by geneb
Tue Dec 04, 2018 9:47 am
Forum: Rostock MAX v3.2
Topic: Rostock MAX v3.2 reviews
Replies: 20
Views: 275

Re: Rostock MAX v3.2 reviews

What would you like to know about it?

g.
by geneb
Tue Dec 04, 2018 9:46 am
Forum: Artemis
Topic: Artemis + Y-Adapter + Simplify3D
Replies: 6
Views: 169

Re: Artemis + Y-Adapter + Simplify3D

The only time you /ever/ need to upgrade the Artemis firmware is if Duet3D publishes a new build that has a bug fix or new feature that you want or need. Unlike the RAMBo firmware, every single aspect of how the Artemis firmware works is controlled by the config.g, config-override.g, and other "...
by geneb
Tue Dec 04, 2018 9:01 am
Forum: Rostock MAX v3.2
Topic: V3.2 Carbon Fiber Rod upgrade
Replies: 8
Views: 283

Re: V3.2 Carbon Fiber Rod upgrade

The carbon fiber arms work on both the v3.2 (or 3!) and the Artemis.

g.
by geneb
Tue Dec 04, 2018 8:59 am
Forum: Rostock MAX v3.2
Topic: Duet Z-Probe Problems
Replies: 3
Views: 77

Re: Duet Z-Probe Problems

You should really only need to run the First Probe and Bed Mapping macros to fully calibrate your machine.

g.
by geneb
Mon Dec 03, 2018 7:45 am
Forum: What are YOU making?
Topic: Coming soon from 713Maker.com
Replies: 69
Views: 10249

Re: Coming soon from 713Maker.com

You can't post that without pictures, man. That's just mean. ;)

g.
by geneb
Mon Dec 03, 2018 7:42 am
Forum: Rostock MAX v3.2
Topic: Duet Z-Probe Problems
Replies: 3
Views: 77

Re: Duet Z-Probe Problems

If the hot-end fan is running, it can cause this. It shouldn't affect how the z-probe operates when doing calibration.

g.
by geneb
Sat Dec 01, 2018 11:09 am
Forum: Rostock MAX v3
Topic: Hotend fan issue?
Replies: 2
Views: 82

Re: Hotend fan issue?

You probably have something shorted out - it likely could have happened when you changed nozzles.

g.
by geneb
Fri Nov 30, 2018 7:28 am
Forum: Troubleshooting
Topic: Layer Shifting
Replies: 38
Views: 662

Re: Layer Shifting

400mm/sec is only valid for Duet-equipped machines. Dial it back to around 200mm/sec.

g.
by geneb
Fri Nov 30, 2018 7:27 am
Forum: Rostock MAX v3
Topic: What are the benefits of upgrading my Rostock Max V3 to a V3.2
Replies: 15
Views: 1088

Re: What are the benefits of upgrading my Rostock Max V3 to a V3.2

I would contact support about that.

g.
by geneb
Thu Nov 29, 2018 8:32 am
Forum: Troubleshooting
Topic: Layer Shifting
Replies: 38
Views: 662

Re: Layer Shifting

What I would do is try the HE280 profile for Cura. You can get all the pre-built Cura profiles here: https://github.com/seemecnc/slicing-pro ... master.zip. The HE280 is very similar in performance to the E3Dv6, so it should work with no tweaking.

g.

Go to advanced search