Search found 4579 matches

by geneb
Wed Apr 18, 2018 7:49 am
Forum: Troubleshooting
Topic: Duet WiFi with E3V6 dragging on plate
Replies: 36
Views: 1915

Re: Duet WiFi with E3V6 dragging on plate

Unless you take your glass off or rotate it, there's usually no reason to re-run the map.

g.
by geneb
Tue Apr 17, 2018 8:10 am
Forum: Artemis
Topic: Enable strain gauge Z probe?
Replies: 17
Views: 504

Re: Enable strain gauge Z probe?

Understand that there's a difference between auto-level and auto-calibration. Broadly speaking the terms can be interchangeable, but when you're into the weeds like this, it's important to know which is which. What G32 does is auto-calibration. The series of probes it does allows a solver to ensure ...
by geneb
Mon Apr 16, 2018 9:13 am
Forum: Rostock MAX v3
Topic: Autoleveling issue
Replies: 1
Views: 79

Re: Autoleveling issue

I would check the connector to make sure that the pins are fully seated in the connector shell and that the connector is fully seated on the RAMBo. What you're describing sounds like a wiring issue.

g.
by geneb
Mon Apr 16, 2018 9:10 am
Forum: Troubleshooting
Topic: Sudden stop during 1st layer, 0 deg -> Killed
Replies: 24
Views: 484

Re: Sudden stop during 1st layer, 0 deg -> Killed

Have you tried setting the Z height through the control panel?

g.
by geneb
Fri Apr 13, 2018 7:51 am
Forum: Artemis
Topic: Heater issues
Replies: 8
Views: 141

Re: Heater issues

You do an M303 Heater 1 Temp 210 M303 H1 S210 Followed by an M303 Write the parameters down Then check config.g and config-override.g Under M307 command you should see the parameters you wrote down. (just a tweak to the above) Tack an M501 to the bottom of your config.g file so that it will load co...
by geneb
Tue Apr 10, 2018 8:26 am
Forum: Rostock MAX v2
Topic: Hot end won't turn off
Replies: 11
Views: 391

Re: Hot end won't turn off

D'oh. :D

g.
by geneb
Tue Apr 10, 2018 8:25 am
Forum: Artemis
Topic: ABS recommendations
Replies: 2
Views: 105

Re: ABS recommendations

I'll second the AquaNet tip - the heated bed performance is a lot better with the Artemis since the heat spreader gives a much more even heat. Just be aware that the vinyl decal on the heat spreader will darken at higher temps. (Unless you've got one of the black anodized beds, then you don't have a...
by geneb
Mon Apr 09, 2018 9:12 am
Forum: Troubleshooting
Topic: Duet WiFi with E3V6 dragging on plate
Replies: 36
Views: 1915

Re: Duet WiFi with E3V6 dragging on plate

Again, M500 doesn't have anything to do with calibration. All it does is output any differences between config.g and the in-ram configuration out to a file called config-override.g. This entry lists what exactly is stored when M500 is executed: https://duet3d.dozuki.com/Wiki/Gcode#Section_M500_Store...
by geneb
Mon Apr 09, 2018 8:56 am
Forum: Rostock MAX v2
Topic: Hot end won't turn off
Replies: 11
Views: 391

Re: Hot end won't turn off

You could also buy the SE300 heater block. That takes the new cartridge thermistor and is a drop-in replacement for the older style HE280 heater block.

g.
by geneb
Mon Apr 09, 2018 8:45 am
Forum: Rostock MAX v2
Topic: Replace nozzle "old" style
Replies: 7
Views: 412

Re: Replace nozzle "old" style

TIL!

BTW, are you familiar with the adventures of Luke Vaxhacker and Dec Vadic? :D

g. (former owner of a VAX 8250)
by geneb
Sun Apr 08, 2018 11:07 am
Forum: Artemis
Topic: T-Slot Roll in for 10 Series 1/4 w 4mm or 5mm
Replies: 8
Views: 223

Re: T-Slot Roll in for 10 Series 1/4 w 4mm or 5mm

I don't know the answer to the RAMBo question, sorry.

The crimpers (PA-09 AND -21) will end up in a drawer with the other dozen+ normal & aerospace crimp tools I have. ;)

g.
by geneb
Sun Apr 08, 2018 10:40 am
Forum: Troubleshooting
Topic: Duet WiFi with E3V6 dragging on plate
Replies: 36
Views: 1915

Re: Duet WiFi with E3V6 dragging on plate

M500 doesn't calibrate anything, it just writes changed things to config-override.g.

g.
by geneb
Sun Apr 08, 2018 10:33 am
Forum: Rostock MAX v2
Topic: Hot end won't turn off
Replies: 11
Views: 391

Re: Hot end won't turn off

The thermistor hasn't been discontinued, it's just sold out.

They should have stock on them shortly.

g.
by geneb
Fri Apr 06, 2018 9:46 am
Forum: Artemis
Topic: T-Slot Roll in for 10 Series 1/4 w 4mm or 5mm
Replies: 8
Views: 223

Re: T-Slot Roll in for 10 Series 1/4 w 4mm or 5mm

No image is appearing.

g.
by geneb
Thu Apr 05, 2018 8:50 am
Forum: Artemis
Topic: Duet Tuning.
Replies: 14
Views: 471

Re: Duet Tuning.

Since you just cost me $44 for a new crimping tool *shakes fist*, I'm going to cost you $52 for a very excellent set of magnifiers: https://www.amazon.com/gp/product/B012M3IV80 :D :D :D These have a focal length of around 420mm, which means you're working at arms length, not 2" from your face. ...
by geneb
Thu Apr 05, 2018 8:39 am
Forum: New Member introduction
Topic: Oldie but Newbie
Replies: 1
Views: 80

Re: Oldie but Newbie

\o/
by geneb
Thu Apr 05, 2018 8:36 am
Forum: Troubleshooting
Topic: Duet WiFi with E3V6 dragging on plate
Replies: 36
Views: 1915

Re: Duet WiFi with E3V6 dragging on plate

I do this myself - my start gcode includes a G32 right after the G28. :)

g.
by geneb
Thu Apr 05, 2018 8:33 am
Forum: New Member introduction
Topic: New to 3D printing and need help
Replies: 7
Views: 269

Re: New to 3D printing and need help

Those may be the old arms, I'm not sure. I _think_ those arms are measured from hole center to hole center, not end to end.

g.
by geneb
Wed Apr 04, 2018 7:59 am
Forum: Artemis
Topic: T-Slot Roll in for 10 Series 1/4 w 4mm or 5mm
Replies: 8
Views: 223

Re: T-Slot Roll in for 10 Series 1/4 w 4mm or 5mm

Nice! You could throw a heat-set insert into it as well.

g.
by geneb
Wed Apr 04, 2018 7:57 am
Forum: The Lounge
Topic: Question on tape covered melamine source
Replies: 4
Views: 305

Re: Question on tape covered melamine source

They apply the tape before they cut it, it doesn't ship that way. You can buy rolls of masking tape wide enough to cover your material.

g.
by geneb
Wed Apr 04, 2018 7:55 am
Forum: Artemis
Topic: Duet Tuning.
Replies: 14
Views: 471

Re: Duet Tuning.

Holy Overkill, Batman! :D

Go here, http://www.hansenhobbies.com/products/c ... in_lp_1x4/ and grab a male 1x4 housing (2nd item down).

They also sell a ratcheting crimp tool that works wonderfully.

g.
by geneb
Wed Apr 04, 2018 7:47 am
Forum: New Member introduction
Topic: New to 3D printing and need help
Replies: 7
Views: 269

Re: New to 3D printing and need help

Can you post a photo of the machine? That might help date it.

g.
by geneb
Tue Apr 03, 2018 8:37 am
Forum: Troubleshooting
Topic: Cura 3.2.1 printer selection for Rostock V3.2
Replies: 3
Views: 175

Re: Cura 3.2.1 printer selection for Rostock V3.2

You're welcome!

g.
by geneb
Mon Apr 02, 2018 8:58 am
Forum: Troubleshooting
Topic: Cura 3.2.1 printer selection for Rostock V3.2
Replies: 3
Views: 175

Re: Cura 3.2.1 printer selection for Rostock V3.2

Here's the cure to those ills: https://seemecnc.dozuki.com/Guide/Setti ... 87?lang=en :)

FYI, when version Cura 3.3 is released it will include selections for SeeMeCNC's printers.

g.
by geneb
Mon Apr 02, 2018 8:55 am
Forum: Troubleshooting
Topic: Sudden stop during 1st layer, 0 deg -> Killed
Replies: 24
Views: 484

Re: Sudden stop during 1st layer, 0 deg -> Killed

Until you figure out the SD card issue, you can print gcode you sliced in the current Cura using MC. You could also use this as excuse to set up OctoPrint and use that to print files uploaded from Cura. ;)

g.

Go to advanced search