Search found 1337 matches

by Mac The Knife
Tue Oct 23, 2018 12:06 pm
Forum: Troubleshooting
Topic: Stop during Calibration
Replies: 1
Views: 5

Re: Stop during Calibration

Check that the wiring harness is still securely seated in the connector on the hotend,,,,, assuming you "upgraded" to the 280 hotend.
by Mac The Knife
Thu Oct 11, 2018 7:50 am
Forum: New Member introduction
Topic: Fresh off the block
Replies: 2
Views: 188

Re: Fresh off the block

At the least it needs to be dried out,,,,, abs absorbs water. 4 to 6 hours in an oven set at 180 F would do wonders. For the initial setting up, calibrating, etc. I would buy a fresh spool.
by Mac The Knife
Wed Oct 10, 2018 10:19 am
Forum: Other
Topic: CURA
Replies: 7
Views: 177

Re: CURA

Cura is the recommended slicer for Artemis, so we should probably have a thread for it. I have been using 3.4.1 - which is a bit later than the version mentioned in the Artemis docs. Today I got an automated notice that 3.5 is available - and an invitation to download it. Anyone try this yet, eithe...
by Mac The Knife
Mon Sep 24, 2018 8:06 am
Forum: Artemis
Topic: When (& how) to update firmware.
Replies: 4
Views: 217

Re: When (& how) to update firmware.

A good rule of thumb is, if it ain't broke, don't fix it.

Myself, in the beginning, I would update, just to update. Now? Only if I'm trying to solve a problem.
by Mac The Knife
Sat Sep 15, 2018 11:08 am
Forum: Troubleshooting
Topic: Rostock Max v3 Stops Moving after a while
Replies: 12
Views: 359

Re: Rostock Max v3 Stops Moving after a while

I wonder if it would fit inside an Eris? Too many projects, not enough time,,,,
by Mac The Knife
Wed Sep 12, 2018 12:51 pm
Forum: Troubleshooting
Topic: Rostock Max v3 Stops Moving after a while
Replies: 12
Views: 359

Re: Rostock Max v3 Stops Moving after a while

Are you printing off of the SD card, or over the USB cable?
by Mac The Knife
Mon Sep 10, 2018 8:02 am
Forum: Troubleshooting
Topic: HE280 Rev B Hotend issues
Replies: 2
Views: 116

Re: HE280 Rev B Hotend issues

You state that the old hotend heater doesn not come on automatically,,,, Does it come on when the RamBo calls for heat?

When Mosfets fail, they normally fail "On", causing the heater to be on all the time.
by Mac The Knife
Tue Aug 28, 2018 12:09 pm
Forum: Troubleshooting
Topic: heat break stuck
Replies: 18
Views: 981

Re: heat break stuck

warm the hotend to around 200 C, then re tighten the nozzle before you print.
the aluminum heat block expands more than the nozzle, and heat break, which causes the nozzle to loosen and leak.
by Mac The Knife
Fri Aug 17, 2018 8:56 am
Forum: Rostock MAX v2
Topic: V2 (mid 2016) to V3.2 (current) upgrade?
Replies: 22
Views: 1208

Re: V2 (mid 2016) to V3.2 (current) upgrade?

They have all appeared to flock to facebook,,,,,, Not a very good repository for specific problems and solutions.
by Mac The Knife
Mon Jul 16, 2018 7:57 am
Forum: Troubleshooting
Topic: Retraction: high pitched motor
Replies: 1
Views: 125

Re: Retraction: high pitched motor

Let's start with what are your current retraction settings?
by Mac The Knife
Tue Jul 03, 2018 7:26 am
Forum: Troubleshooting
Topic: Print failure when printing vertical columns?
Replies: 12
Views: 536

Re: Print failure when printing vertical columns?

I would try printing with a brim attached to the print,,, possibly as high as 3 layer thick.
by Mac The Knife
Thu Jun 28, 2018 7:16 pm
Forum: Troubleshooting
Topic: Hotend never reaches Temp
Replies: 12
Views: 438

Re: Hotend never reaches Temp

Gene has a video on youtube showing how to replace the resistors with a heater cartridge in the hotend. Myself, I installed two,,,,, to keep the hater block balanced.
by Mac The Knife
Thu Jun 28, 2018 7:40 am
Forum: Troubleshooting
Topic: Hotend never reaches Temp
Replies: 12
Views: 438

Re: Hotend never reaches Temp

I was going to post that that you need to tighten the power supply connections at the RamBo, but you say you've already done that.
by Mac The Knife
Thu Jun 14, 2018 12:13 pm
Forum: Troubleshooting
Topic: Filament Feeding Problem
Replies: 5
Views: 347

Re: Filament Feeding Problem

A new hotend? And after you installed a new hotend you started to have a problem?
by Mac The Knife
Sat Jun 09, 2018 10:46 am
Forum: Troubleshooting
Topic: can not connect to printer
Replies: 4
Views: 283

Re: can not connect to printer

It appears that there is more traffic by SeeMeCNC people on their Facebook page than there is here. You might get a faster response there.
by Mac The Knife
Fri Jun 01, 2018 1:11 pm
Forum: What are YOU making?
Topic: Coming soon from 713Maker.com
Replies: 65
Views: 9169

Re: Coming soon from 713Maker.com

Nice looking storefront. Except for the "Currently out of stock" items!!!!!
by Mac The Knife
Fri Jun 01, 2018 11:32 am
Forum: What are YOU making?
Topic: Coming soon from 713Maker.com
Replies: 65
Views: 9169

Re: Coming soon from 713Maker.com

I sent a request in for a bed platform for my Folgertech FT-5 R2, a month ago, and haven't heard anything back.
by Mac The Knife
Wed May 30, 2018 7:26 am
Forum: Nuts and Bolts
Topic: What is in your tool chest?
Replies: 3
Views: 1932

Re: What is in your tool chest?

I bought the IWISS 28B, Ratcheting crimpers off of Amazon. They work really well. http://a.co/jiewv7g
by Mac The Knife
Fri May 25, 2018 8:02 am
Forum: Troubleshooting
Topic: ERIS - Clicking Sound, No Filament Coming Out, Unload Doesn't Work :(
Replies: 8
Views: 430

Re: ERIS - Clicking Sound, No Filament Coming Out, Unload Doesn't Work :(

I've had to trim the end of the ptfe back a little bit so that the connector would have fresh material to bite into, otherwise I would have a hockey puck form causing my jam. I use a heat break from my V2 hotend, and a razor blade to trim the tube square so it seals.
by Mac The Knife
Wed May 16, 2018 7:39 am
Forum: What are YOU making?
Topic: Tiny Track - FPV RC
Replies: 3
Views: 472

Re: Tiny Track - FPV RC

No, there isn't, but installing a new hotend isn't hard,,, That is if you're installing a stock hotend.
by Mac The Knife
Fri Apr 27, 2018 8:32 am
Forum: GCode & Test Prints
Topic: GCode for Cyclops Dual Extruders
Replies: 6
Views: 1847

Re: GCode for Cyclops Dual Extruders

Even better, your question is looks to be better suited in the Ramps section of the forum,,,, viewforum.php?f=30
by Mac The Knife
Wed Apr 18, 2018 12:28 pm
Forum: RailCore
Topic: Duet 2 Maestro
Replies: 7
Views: 875

Re: Duet 2 Maestro

My take away from watching that clip is that it will not perform the same as the Duet 2, and tailored more for the OEMs,,, But I nominate you to get back with us on your impressions. The Duet 3 on the other hand,,,,,
by Mac The Knife
Wed Apr 18, 2018 12:17 pm
Forum: The Build Zone
Topic: Converting MAX v3 to ATX PSU
Replies: 6
Views: 760

Re: Converting MAX v3 to ATX PSU

My opinion would be that it would be easier to change the fan in the existing power supply.
by Mac The Knife
Thu Apr 05, 2018 8:18 am
Forum: New Member introduction
Topic: New to 3D printing and need help
Replies: 10
Views: 803

Re: New to 3D printing and need help

For print leveling to work, the controller needs to have a sensor to notify it that the nozzle has touched the bed. What you show does not have a sensor. The Arms the previous owner put on appear to be by Trick Laser. He shows 300 mm for the arms he currently sells,,,, You have the old style, but th...
by Mac The Knife
Wed Apr 04, 2018 7:24 am
Forum: New Member introduction
Topic: New to 3D printing and need help
Replies: 10
Views: 803

Re: New to 3D printing and need help

Unless the previous owner added a sensor of some sorts, print leveling will not work,,, and you would have to adjust it manually. Post some pictures, it may help identify what you got there.

Go to advanced search