Search found 201 matches

by rootboy
Mon Aug 20, 2018 2:14 am
Forum: Troubleshooting
Topic: Extruded filament has gaps, is not consistent.
Replies: 1
Views: 80

Re: Extruded filament has gaps, is not consistent.

Loose hob gear on the extruder? Although I would expect to see it get worse at higher speeds if that was the issue. But, I'd check it anyways.
by rootboy
Mon Aug 20, 2018 2:12 am
Forum: Troubleshooting
Topic: Bed Adhesion Issue
Replies: 2
Views: 86

Re: Bed Adhesion Issue

And don't be afraid to squish the first layer down a bit (lower your Z height).
by rootboy
Mon Aug 20, 2018 2:09 am
Forum: Troubleshooting
Topic: TPU Fail or no?
Replies: 1
Views: 93

Re: TPU Fail or no?

I did notice this material drewls a lot at that temp, but lower and it would not extrude. That's a sign of moisture in your filament. Try upping the drying temp or the drying time. Just be sure to keep the oven under TPU's Glass Transition temp (AKA, melting point). We use a Dremel 3D Digilab 3D45 ...
by rootboy
Mon Aug 20, 2018 1:31 am
Forum: Troubleshooting
Topic: RMV2 - Control knob half-works
Replies: 3
Views: 171

Re: RMV2 - Control knob half-works

Sounds to me like it has the wrong DEF's for the Atmega I/O pins. But I'd start with the EEPROM settings. IIRC, Gene has a nice section in the manual on how to do it. Anyone ever experienced this level of hell I've been going through since purchase? :( Oh, how I feel your pain... :) About all that i...
by rootboy
Mon Aug 20, 2018 1:14 am
Forum: Troubleshooting
Topic: heat break stuck
Replies: 14
Views: 461

Re: heat break stuck

Silly question, but is your hotend fan working?
by rootboy
Mon Aug 20, 2018 1:12 am
Forum: Troubleshooting
Topic: Stepper motors just stopped working?
Replies: 7
Views: 128

Re: Stepper motors just stopped working?

Sounds like something wonky in the config. Have you tried controlling it from different software?
by rootboy
Mon Aug 20, 2018 1:10 am
Forum: Troubleshooting
Topic: Print starting before Hotend heats
Replies: 8
Views: 117

Re: Print starting before Hotend heats

You could try sending it a M116 command first (M116 - Wait for all temperatures in a +/- 1 degree range)

And what do you have "#define PRINTER_FLAG1_ALLOW_COLD_EXTRUSION" set to? In my Repetier it shows 128. It's in the "Printer.h" file.
by rootboy
Sat Jun 23, 2018 12:34 am
Forum: Troubleshooting
Topic: first probe problem v3.2
Replies: 1
Views: 220

Re: first probe problem v3.2

I read through your troubleshooting steps on the Duet site, and I noticed that your SD card is addressed to "0", and that you got it to work. But the macros that you are trying to use access SD card "1". You don't have a SD card "1", so edit your macros to point to SD c...
by rootboy
Sat Jun 23, 2018 12:04 am
Forum: Troubleshooting
Topic: Orion Prints not coming out square
Replies: 2
Views: 184

Re: Orion Prints not coming out square

Check your platform for play. Are you using a printed platform? If so, consider replacing it with a machined or injection molded one. My V2 would print out a 100mm calibration block with the center measuring 10mm, the Z end measuring 10.2mm, and the Y end measuring 9.8mm. Replacing the platform with...
by rootboy
Fri Jun 22, 2018 11:59 pm
Forum: Troubleshooting
Topic: Display lights but no characters, just squares
Replies: 4
Views: 572

Re: Display lights but no characters, just squares

Square blocks sounds like a problem with your contrast control. Check that first.
by rootboy
Fri Jun 22, 2018 11:57 pm
Forum: Troubleshooting
Topic: EZR Struders clicking/bowden connectors move slighly
Replies: 1
Views: 195

Re: EZR Struders clicking/bowden connectors move slighly

I really don't miss my EZStruder, I yanked mine ages ago. But in the interests of being helpful, would a dab of epoxy keep it in place? I can't recall if you will ever need to pull that apart to work on it, if not then glue it in and forget it. But I would upgrade to a better extruder. I'm testing o...
by rootboy
Fri Jun 22, 2018 11:33 pm
Forum: Troubleshooting
Topic: Max V2 works, but this connector can't be right
Replies: 3
Views: 291

Re: Max V2 works, but this connector can't be right

You can replace the plug (the burnt part), but I'm sure that the socket was damage as well. I would replace both and you should be good to go. And I gave away my Rambo board after my upgrade to my Duet, so I don't know offhand what this terminal feeds. But I would have to guess that this is the heat...
by rootboy
Fri Jun 22, 2018 11:09 pm
Forum: Troubleshooting
Topic: Filiment stuck at hotend
Replies: 6
Views: 234

Re: Filiment stuck at hotend

Or, as in my case, I managed to not notice that I had my fan leads swapped on the Duet board until PLA started getting stuck in the cold end of the hot end. It was pretty obvious what the problem was when I pulled the filament out and saw the it had gobbed up in the cold end. So, check your fan, it ...
by rootboy
Fri Jun 22, 2018 11:02 pm
Forum: Troubleshooting
Topic: Filament Feeding Problem
Replies: 5
Views: 268

Re: Filament Feeding Problem

You didn't happen to change the nozzle size with the new hotend and not update your settings?
by rootboy
Fri Jun 22, 2018 11:00 pm
Forum: Troubleshooting
Topic: Duet Wifi web console issues
Replies: 6
Views: 417

Re: Duet Wifi web console issues

I had random to severe dropout issues until I disconnected my USB cable. Now it hardly ever drops out.
by rootboy
Thu Jun 21, 2018 9:19 pm
Forum: Troubleshooting
Topic: mesh calibration issues
Replies: 10
Views: 292

Re: mesh calibration issues

SeeMeCNC has their own version of the Smart Effector now, and that may fit your ball and socket arms better. The Duet3D one is designed to be used with magnetic joints. Good to know, thanks! After knocking one of the plungers loose (the Z axis), the map has improved immensely. What I am thinking ab...
by rootboy
Thu Jun 21, 2018 9:12 pm
Forum: Troubleshooting
Topic: mesh calibration issues
Replies: 10
Views: 292

Re: mesh calibration issues

Anytime! :)

I de-attached one of the plungers and things are looking much better...
by rootboy
Thu Jun 21, 2018 4:24 am
Forum: Troubleshooting
Topic: mesh calibration issues
Replies: 10
Views: 292

Re: mesh calibration issues

I just signed up there the other day, so no reason. :) But I thought it would be a good way to showcase a solution here that I wasn't even aware of until a few weeks ago. :) After I got medieval with the plate the other day, my alignment is much better with my FSRs, still not great however. I will p...
by rootboy
Sun Jun 17, 2018 9:53 am
Forum: Troubleshooting
Topic: mesh calibration issues
Replies: 10
Views: 292

Re: mesh calibration issues

Observe your hotend as it probes each point. Do you see the hotend sliding horizontally any? Or does it make a quick tap and moves on to the next one? If you see it sliding, then it's your FSR mount causing the problem. 713Maker makes aluminum mounts for the JohnSL FSRs. This is what I use on mine. ...
by rootboy
Sat Apr 28, 2018 4:11 pm
Forum: Troubleshooting
Topic: Print quality woes
Replies: 15
Views: 1735

Re: Print quality woes

Nice setup! And I'm glad to hear that you got it fixed! :)
by rootboy
Wed Apr 25, 2018 7:48 am
Forum: Troubleshooting
Topic: Cant seem to Calibrate it right.
Replies: 20
Views: 856

Re: Cant seem to Calibrate it right.

Thanks Gene! :)
by rootboy
Tue Apr 24, 2018 11:13 pm
Forum: Troubleshooting
Topic: Cant seem to Calibrate it right.
Replies: 20
Views: 856

Re: Cant seem to Calibrate it right.

Oh yeah, this is what it looked like before:

Cal map 3.png
by rootboy
Tue Apr 24, 2018 10:23 pm
Forum: Troubleshooting
Topic: Cant seem to Calibrate it right.
Replies: 20
Views: 856

Re: Cant seem to Calibrate it right.

Not too bad...

Cal map 4.png
by rootboy
Tue Apr 24, 2018 10:11 pm
Forum: Troubleshooting
Topic: Cant seem to Calibrate it right.
Replies: 20
Views: 856

Re: Cant seem to Calibrate it right.

I had looked for FSR mounts but didn't come up with anything, so I used the three wedges that came with the plate. And I found what was wrong with my "problem child" sensor, I had it mounted too far to one side and not on the center. It might not fix it entirely, but at the very least it's...
by rootboy
Tue Apr 24, 2018 12:22 am
Forum: Troubleshooting
Topic: Cant seem to Calibrate it right.
Replies: 20
Views: 856

Re: Cant seem to Calibrate it right.

Things are worse after trying to adjust my FSRs, which makes me wonder how reliable this system is going to be long-term. I'll probably try new FSRs too, but I can see how one corner sticking will end up making things worse than not calibrating at all.

Go to advanced search